DOI QR코드

DOI QR Code

MBF 20으로 브레이징한 STS304 콤팩트 열교환기 접합부의 미세조직에 미치는 가열속도의 영향

Effect of Heating Rates on Microstructures in Brazing Joints of STS304 Compact Heat Exchanger using MBF 20

  • Kim, Jun-Tae (Dept. of Applied Hybrid Materials, Pusan National University) ;
  • Heo, Hoe-jun (Dept. of Material Science and Engineering, Pusan National University) ;
  • Kim, Hyeon-Jun (DongHwa Entec Co., Ltd. R&D Center) ;
  • Kang, Chung-Yun (Dept. of Material Science and Engineering, Pusan National University)
  • 투고 : 2015.12.04
  • 심사 : 2016.01.27
  • 발행 : 2016.04.30

초록

Effect of heating rate on microstructure of brazed joints with STS 304 Printed Circuit Heat Exchanger (PCHE),which was manufactured as large-scale($1170(L){\times}520(W)){\times}100(T)$, mm), have been studied to compare bonding phenomenon. The specimens using MBF 20 was bonded at $1080^{\circ}C$ for 1hr with $0.38^{\circ}C/min$ and $20^{\circ}C/min$ heating rate, respectively. In case of a heating rate of $20^{\circ}C/min$, overflow of filler metal was observed at the edge of a brazed joints showing the height of filler metal was decreased from $100{\mu}m$ to $68{\mu}m$. At the center of the joints, CrB and high Ni contents of ${\gamma}$-Ni was existed. For the joints brazed at a heating rate of $0.38^{\circ}C/min$, the height of filler was decreased from $100{\mu}m$ to $86{\mu}m$ showing the overflow of filler was not appeared. At the center of the joints, only ${\gamma}$-Ni was detected gradating the Ni contents from center. This phenomenon was driven from a diffusion amount of Boron in filler metal. With a fast heating rate $20^{\circ}C/min$, diffusion amount of B was so small that liquid state of filler metal and base metal were reacted. But, for a slow heating rate $0.38^{\circ}C/min$, solid state of filler metal due to low diffusion amount of B reacted with base metal as a solid diffusion bonding.

키워드

참고문헌

  1. Ae-Jeong Jeon et al., J. Welding and Jopining, 32(4) (2014), 384-392 (in Korean)
  2. Li, Qi, et al., RENEW SUST ENERG REV, 15(9) (2011), 4855-4875 https://doi.org/10.1016/j.rser.2011.07.066
  3. Takeda Takeshi, et al., NUCL ENG DES, 168(1) (1997), 11-21 https://doi.org/10.1016/S0029-5493(96)01361-1
  4. 조흥곤, 기계산업 452 단일호 (2015), 64-72 (in Korean)
  5. Sabharwall Piyush, et al., J. Thermal Sci. Eng. Appl., 5(1) (2013), 011009 https://doi.org/10.1115/1.4007578
  6. Jiang, Wenchun, Jianming Gong, and Shan-Tung Tu., MATER DESIGN, 31(1) (2010), 648-653 https://doi.org/10.1016/j.matdes.2009.04.039
  7. Jeong-Woo Yu, et al., Journal of KWJS, 30(6) (2012), 106-112 (in Korean)
  8. Ngo, Tri Lam, et al., EXP THERM FLUID SCI, 30(8) (2006), 811-819 https://doi.org/10.1016/j.expthermflusci.2006.03.010
  9. Nikitin, Konstantin, Yasuyoshi Kato, and Lam Ngo., INT J REFRIG, 29(5) (2006), 807-814 https://doi.org/10.1016/j.ijrefrig.2005.11.005
  10. Gale, W. F. and D. A. Butts., SCI TECHNOL WELD JOI, 9(4) (2004), 283-300. https://doi.org/10.1179/136217104225021724
  11. Yong-Won Lee and Jong-Hoon Kim., Korean Journal of Materials Research, 17(3) (2007), 179-183 https://doi.org/10.3740/MRSK.2007.17.3.179
  12. Chung-Yun Kang, et al., Journal of KWS, 17(2) (1999), 1-8 (in Korean)
  13. Chung-Yun Kang, et al., Journal of KWS, 21(3) (2003), 21-3 (in Korean)
  14. J. Lemus-Ruiiz et al., J MATER PROCESS TECH, 223 (2015), 16-21 https://doi.org/10.1016/j.jmatprotec.2015.03.038
  15. Wenchun Jiang, Jianming Gong, MATER DESIGN, 32(2) (2011), 736-742 https://doi.org/10.1016/j.matdes.2010.07.032
  16. R K Roy, H Bapari, A K Panda, A Mitra, SCI TECHNOL WELD JOI, 18(3) (2013), 216-221 https://doi.org/10.1179/1362171812Y.0000000081
  17. Ruiz-Vargas, J, et al., J MATER PROCESS TECH, 213(1) (2013), 20-29 https://doi.org/10.1016/j.jmatprotec.2012.07.016