Current Photovoltaic Research

  • 제4권1호
  • /
  • Pages.12-15
  • /
  • 2016
  • /
  • 2288-3274(pISSN)
  • /
  • 2508-125X(eISSN)
한국태양광발전학회 (Korea Photovoltaic Society)
권호 표지
DOI QR코드

DOI QR Code

Investigation of Firing Conditions for Optimizing Aluminum-Doped p+-layer of Crystalline Silicon Solar Cells

  • Lee, Sang Hee (Green Strategic Energy Research Institute, Department of Electronics Engineering, Sejong University) ;
  • Lee, Doo Won (Green Strategic Energy Research Institute, Department of Electronics Engineering, Sejong University) ;
  • Shin, Eun Gu (Green Strategic Energy Research Institute, Department of Electronics Engineering, Sejong University) ;
  • Lee, Soo Hong (Green Strategic Energy Research Institute, Department of Electronics Engineering, Sejong University)
  • 투고 : 2016.02.23
  • 심사 : 2016.02.29
  • 발행 : 2016.03.31
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Screen printing technique followed by firing has commonly been used as metallization for both laboratory and industrial based solar cells. In the solar cell industry, the firing process is usually conducted in a belt furnace and needs to be optimized for fabricating high efficiency solar cells. The printed-Al layer on the silicon is rapidly heated at over $800^{\circ}C$ which forms a layer of back surface field (BSF) between Si-Al interfaces. The BSF layer forms $p-p^+$ structure on the rear side of cells and lower rear surface recombination velocity (SRV). To have low SRV, deep $p^+$ layer and uniform junction formation are required. In this experiment, firing process was carried out by using conventional tube furnace with $N_2$ gas atmosphere to optimize $V_{oc}$ of laboratory cells. To measure the thickness of BSF layer, selective etching was conducted by using a solution composed of hydrogen fluoride, nitric acid and acetic acid. The $V_{oc}$ and pseudo efficiency were measured by Suns-$V_{oc}$ to compare cell properties with varied firing condition.

키워드

참고문헌

  1. Meemongkolkiat V, Nakayashiki K, Kim DS, Kopecek R, Rohatgi A, "Factors limiting the formation of uniform and thick aluminum back-surface field and its potential", Journal of the Electrochemical Society, Vol. 153, Issue 1, 2006, pages G53-G58. https://doi.org/10.1149/1.2129106
  2. Hilali MM, Nakayashiki K, Khadilkar C, Reedy RC, Rohatgi A, Shaikh A, et al., "Effect of Ag particle size in thick-film Ag paste on the electrical and physical properties of screen printed contacts and silicon solar cells", Journal of the Electrochemical Society, Vol. 153, Issue 1, 2006, pages A5-A11. https://doi.org/10.1149/1.2126579
  3. Gatz S, Hannebauer H, Hesse R, Werner F, Schmidt A, Dullweber T, et al., "19.4%‐efficient large‐area fully screen‐printed silicon solar cells", physica status solidi (RRL)-Rapid Research Letters, Vol. 5, Issue 4, 2011, pages 147-149. https://doi.org/10.1002/pssr.201105045
  4. Loelgen P, Leguijt C, Eikelboom J, Steeman R, Sinke W, Verhoef L, et al., editors, "Aluminium back-surface field doping profiles with surface recombination velocities below 200 cm/s", IEEE Photovoltaic Specialists Conference, 1993.
  5. Rauer M, Woehl R, Ruhle K, Schmiga C, Hermle M, Horteis M, et al., "Aluminum alloying in local contact areas on dielectrically passivated rear surfaces of silicon solar cells", IEEE Electron Device Letters, Vol. 32, Issue 7, 2011, pages 916-918. https://doi.org/10.1109/LED.2011.2143385
  6. Gatz S, Bothe K, Muller J, Dullweber T, Brendel R, "Analysis of local Al-doped back surface fields for high efficiency screenprinted solar cells", Energy Procedia, Vol. 8, 2011, pages 318-323. https://doi.org/10.1016/j.egypro.2011.06.143
  7. Rohatgi A, Narasimha S, Ebong AU, Doshi P, "Understanding and implementation of rapid thermal technologies for high-efficiency silicon solar cells", IEEE Transactions on Electron Devices, Vol. 46, Issue 10, 1999, pages 1970-1977. https://doi.org/10.1109/16.791984
  8. Narasimha S, Rohatgi A, Weeber A, "An optimized rapid aluminum back surface field technique for silicon solar cells", IEEE Transactions on Electron Devices, Vol. 46, Issue 7, 1999, pages 1363-1370. https://doi.org/10.1109/16.772477
  9. Rauer M, Schmiga C, Hermle M, Glunz SW, "Effectively surface‐passivated aluminium‐doped p+ emitters for n‐type silicon solar cells", physica status solidi (a), Vol. 207, Issue 5, 2010, pages 1249-1251. https://doi.org/10.1002/pssa.200925507
  10. Rauer M, Schmiga C, Krause J, Woehl R, Hermle M, Glunz SW, "Further analysis of aluminum alloying for the formation of p+ regions in silicon solar cells", Energy Procedia, Vol. 8, 2011, pages 200-206.
  11. Krause J, Woehl R, Rauer M, Schmiga C, Wilde J, Biro D, "Microstructural and electrical properties of different-sized aluminum-alloyed contacts and their layer system on silicon surfaces", Solar Energy Materials and Solar Cells, Vol. 95, Issue 8, pages 2151-2160. https://doi.org/10.1016/j.solmat.2011.03.017
  12. Sinton R, Cuevas A, editors, "A quasi-steady-state open-circuit voltage method for solar cell characterization", 16th European Photovoltaic Solar Energy Conference, 2000.
  13. Park SE, "A study on interfacial reaction in aluminum metallization process for crystalline silicon solar cells", Dessertation Thesis, Korea University, Korea, 2012.