대한기계학회논문집A (Transactions of the Korean Society of Mechanical Engineers A)

  • 제39권12호
  • /
  • Pages.1207-1212
  • /
  • 2015
  • /
  • 1226-4873(pISSN)
  • /
  • 2288-5226(eISSN)
대한기계학회 (The Korean Society of Mechanical Engineers)
권호 표지
DOI QR코드

DOI QR Code

P-S-N선도를 이용한 진동리퍼 기어박스-생크 용접부의 피로수명 평가

Evaluation of Fatigue Life of Welded Joint of Gear Box-Shank in Vibro Ripper Using P-S-N Curve

  • 투고 : 2015.03.31
  • 심사 : 2015.10.14
  • 발행 : 2015.12.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

진동리퍼는 암반의 파쇄와 리핑 작업을 동시에 하기 위해서 개발된 장비이며 기존의 암반 파쇄용 유압 브레이커와 작동 원리가 다르다 진동리퍼의 기진력을 투스로 전달하는 기어박스-생크 용접부는 매우 중요한 부분이며 진동리퍼의 기계적 건전성의 예측이 필수적이다. 본 연구는 생크소재 및 용접재료의 변화에 따른 접부의 피로수명 예측을 목적으로 하고 있다. 생크의 재료는 Hadox-hituf, AR 400을 사용하였고 접금속은 CSF-71T, CSF-81T를 사용하였다. 피로시험은 응력비 R=0에서 각 재료조건에 대해서 수행하였다. P-S-N 선도는 JSME-S002 규정에 맞춰 파괴확률 10%, 50%, 90%에 대해서 나타냈으며 수명 예측 식을 도출하였다.

A vibro ripper utilizes high-frequency vibration for rock fragmentation. This concept is different from those used by other existing breakers. The gearbox-shank welded joint of a vibro ripper is a very important part. Because it delivers the vibromotive force to the tooth, it is important to predict its soundness. This study was conducted to predict the fatigue life under welding conditions. The shank materials were Hardox-Hituf and AR400, and the filler metals were CSF-71T and CSF-81T. Fatigue tests were conducted under each set of conditions. P-S-N curves are presented based on the statistical testing method recommended by JSME-S002, and a comparison is made of the results under each set of conditions. The life was estimated using a P-S-N curve.

키워드

참고문헌

  1. Lee, J.H., Ih, J.G., Park, S.H., Ha, T.G. and Lim, J.H., 2001, "Vibro-acoustic Design and Development of a Low-noise Hydraulic Breaker," Journal of the Korean Society for Noise and Vibration Engineering, Vol. 11, No. 5, pp. 148-155.
  2. Park, G.B., Park, C.H., Park, Y.S. and Choi, D.H., 2011, "Optimal Design of Minimizing Weight of Housing of Hydraulic Breaker," Trans. Korean Soc. Mech. Eng. A, Vol.35, No.2, pp. 207-212. https://doi.org/10.3795/KSME-A.2011.35.2.207
  3. Balasubramanian, V. and Guha, B., 1999, "Influence of Weld Size Fatigue Crack Growth Characteristics of Flux Cored are Welded Cruciform Joints," Materials Science and Engineering: A, Vol. 265, Issues 1-2, pp.7-17. https://doi.org/10.1016/S0921-5093(99)00007-6
  4. Lee, Y. B., 2012, "A Study on Characteristics of Fatigue Life in LOP Cruciform Fillet Welding Zone," Journal of the Korean Institute of Gas, Vol. 16, No. 3, pp.29-34. https://doi.org/10.7842/kigas.2012.16.3.029
  5. Chang, K. H. and Lee, C. H., 2007, "Residual Stresses and Fracture Mechanics Analysis of a Crack in Welds of High Strength Steels," Engineering Fracture Mechanics, Vol. 74, Issue 6, pp. 980-994. https://doi.org/10.1016/j.engfracmech.2006.08.012
  6. JSME S002, 1994, "Standard Method Statistical Ftigue Testing," Journal of the Japan Society of Mechanical Engineers, pp. 10-42.
  7. Oh, K. K., Kim, J. H., Kim, Y. W., Park, J. Y., Yang, G. S., Park, J. W. and Kim, S. H., 2014, "Fatigue Characteristics on Welded Joint of Gear Box-Shank in Vibro Ripper for Rock Crash," Journal of the Korean Society of Safety, Vol. 29, No. 6, pp. 28-33. https://doi.org/10.14346/JKOSOS.2014.29.6.028