DOI QR코드

DOI QR Code

Brass fillers in friction composite materials: Tribological and brake squeal characterization for suitable effect evaluation

  • 투고 : 2014.10.31
  • 심사 : 2015.03.23
  • 발행 : 2015.10.25

초록

In this paper, brake pad performance of two organic matrix composites namely, Sample 1 (contains no brass filler) and Sample 2 (contains 1.5% brass filler), is studied based on tribological and squeal noise behavior. In the first stage, a pin-on-disc tribometer is used to evaluate the frictional behavior of the two pads. On the following stage, these pads are tested on squeal noise occurrence using a drag-type brake dynamometer. From the two type of tests, the results show that; (i) brass fillers play a dual role; firstly as reinforcing element of the brake pad providing primary contact sites, and secondly as solid lubricant by contributing to the formation of a layer of granular material providing velocity accommodation between the pad and the disc; (ii) brass fillers contribute to friction force stabilization and smooth sliding behavior; (iii) the presence of small weight quantity of brass filler strongly contributes to squeal occurrences; (iv) there is close correlation between pin-on-disc tribometer and brake dynamometer tests in terms of tribological aspect.

키워드

참고문헌

  1. Bijwe, J., Kumar, M., Gurunath, P.V., Desplanques, Y. and Degallaix, G. (2008), "Optimization of brass contents for best combination of tribo-performance and thermal conductivity of non-asbestos organic (NAO) friction composites", Wear, 265(5-6), 699-712. https://doi.org/10.1016/j.wear.2007.12.016
  2. Cho, M.H., Kim, S.J., Kim, D. and Jang, H. (2005), "Effects of ingredients on tribological characteristics of a brake lining: an experimental case study", Wear, 58(2), 1682-1687.
  3. Eddoumy, F., Kasem, H., Dhieb, H., Gerardus Buijnsters, J., Dufrenoy, F., Celis, J. and Desplanques, Y. (2015), "Role of constituents of friction materials on their sliding behavior between room temperature and $400^{\circ}C$", Mater. Des., 65, 179-186. https://doi.org/10.1016/j.matdes.2014.08.048
  4. Eriksson, M. and Jacobson, S. (2001), "Friction behaviour and squeal generation of disc brakes at low speeds", Proceedings of the Institution of Mechanical Engineers Part D: J. Automob. Eng., 215(12), 1245-1256. https://doi.org/10.1243/0954407011528789
  5. Hentati, N., Najjar, D., Kchaou, M., Cristol, A.-L., Elleuch, R. and Desplanques, Y. (2012), "Experimental study of brake lining molding parameters", Proceeding of the Europe's Braking Conference & Exhibition EUROBRAKE 2012, Dresden, Germany, April.
  6. Jang, H., Lee, J. and Fash, J.W. (2001), "Compositional effects of the brake friction material on creep groan phenomena", Wear, 251(1-12), 1477-1483. https://doi.org/10.1016/S0043-1648(01)00786-4
  7. Jang, H., Koa, K., Kim, S.J., Basch, R.H. and Fash, J.W. (2004), "The effect of metal fibers on the friction performance of automotive brake friction materials", Wear, 256(3-4), 406-414. https://doi.org/10.1016/S0043-1648(03)00445-9
  8. Jayashree, B., Gurunath, P.V., Desplanques, Y. and Degallaix, G. (2008), "Optimization of brass contents for best combination of tribo-performance and thermal conductivity of non-asbestos organic (NAO) friction composites", Wear, 265(5-6), 699-712. https://doi.org/10.1016/j.wear.2007.12.016
  9. Kim, S.S., Hee, H.H., Min, W.S. and Jang, H. (2011), "Friction and vibration of automotive brake pads containing different abrasive particles", Wear, 271(18), 1194-1202. https://doi.org/10.1016/j.wear.2011.05.037
  10. Kumar, M. and Bijwe, J. (2008), "Role of different metallic fillers in non-asbestos organic (NAO) friction composite for controlling sensitivity of coefficient of friction to load and speed", Tribol. Int., 43(5-6), 965-974. https://doi.org/10.1016/j.triboint.2009.12.062
  11. Kumar, M. and Bijwe, J. (2010), "Studies on reduced scale tribometer to investigate the effects of metal additives on friction coefficient-Temperature sensitivity in brake materials", Wear, 269(11-12), 838-846. https://doi.org/10.1016/j.wear.2010.08.012
  12. Kumar, M., Boidin, X., Desplanques, Y. and Bijwe, J. (2011), "Influence of various metallic fillers in friction materials on hot-spot appearance during stop braking", Wear, 270(5-6), 371-381. https://doi.org/10.1016/j.wear.2010.11.009
  13. Massi, F., Berthier, Y. and Baillet, L. (2008), "Contact surface topography and system dynamics of brake squeal", Wear, 265(11-12), 1784-1792. https://doi.org/10.1016/j.wear.2008.04.049
  14. Mat Lazim, A.R., Abdul Hamid, M.K. and Abu Bakar, A.R. (2012), "The effects of pad surface topography on disc brake squeal", Appl. Mech. Mater., 165, 58-62. https://doi.org/10.4028/www.scientific.net/AMM.165.58
  15. Mat Lazim, A.R., Abu Bakar, A.R., Abdul Hamid, M.K., Kchaou, M. and Elleuch, R. (2013), "The effect of road grit particles on tribological and vibrational aspects of commercial brake pads", Proceeding of the Europe's Braking Conference & Exhibition EUROBRAKE 2013, Dresden, Germany, June.
  16. Mat Lazim, A.R., Abu Bakar, A.R. and Kchaou, M. (2014), "The study of disc brake noise on three different types of friction materials", Appl. Mech. Mater., 663, 113-118. https://doi.org/10.4028/www.scientific.net/AMM.663.113
  17. Mini, K.M., Mahadevan, L., Lubin, M. and Girish, K. (2012), "Effect of volume fraction on stability analysis of glass fibre reinforced composite plate", Steel Comp. Struct., Int. J., 12(2), 117-127. https://doi.org/10.12989/scs.2012.12.2.117
  18. Peng, Y., Stacy Van, D. and Rani, F.E. (2015), "An investigation into the mechanics of fiber reinforced composite disk springs", Steel Comp. Struct., Int. J., 18(3), 775-791. https://doi.org/10.12989/scs.2015.18.3.775
  19. Sherif, H. (2004), "Investigation on effect of surface topography of pad/disc assembly on squeal generation", Wear, 257(7-8), 687-695. https://doi.org/10.1016/j.wear.2004.03.015
  20. Woldman, M., VanderHeide, E., Schipper, D.J., Tinga, T. and Masen, M.A. (2012), "Investigating the influence of sand particle properties on abrasive wear behavior", Wear, 294-295, 419-426. https://doi.org/10.1016/j.wear.2012.07.017
  21. Xian, J. and Xiaomei, L. (2004), "Friction and wear characteristics of polymer-matrix friction materials reinforced by brass fibers", J. Mater. Eng. Perform., 13(5), 642-651. https://doi.org/10.1361/10599490420061
  22. Zhao, Y., Lu, Y. and Wright, M.A. (2006), "Sensitivity series and friction surface analysis of nonmetallic friction materials", Mater. Des., 27(10), 833-838. https://doi.org/10.1016/j.matdes.2005.04.005
  23. Zhu, Z., Xu, L., Chen, G. and Li, Y. (2010), "Optimization on tribological properties of aramid fibre and CaSO4 whisker reinforced non-metallic friction material with analytic hierarchy process and preference ranking organization method for enrichment evaluations", Mater. Des., 31(1), 551-555. https://doi.org/10.1016/j.matdes.2009.07.015

피인용 문헌

  1. Squealing characteristics of worn brake pads due to silica sand embedment into their friction layers vol.358-359, 2016, https://doi.org/10.1016/j.wear.2016.04.006
  2. Experimental investigation of the squeal characteristics in railway disc brakes 2018, https://doi.org/10.1177/1350650117754002
  3. Impact of brass contents on thermal, friction and wear properties of brake linings composites vol.19, pp.1, 2018, https://doi.org/10.1051/meca/2016083
  4. A Novel Numerical Method for Considering Friction During Pre-stressing Construction of Cable-Supported Structures pp.2093-6311, 2018, https://doi.org/10.1007/s13296-018-0078-y
  5. Effect of the Friction Block Shape of Railway Brakes on the Vibration and Noise under Dry and Wet Conditions pp.1547-397X, 2019, https://doi.org/10.1080/10402004.2018.1545954
  6. Effect of size and shape of copper alloys particles on the mechanical and tribological behavior of friction materials vol.21, pp.6, 2015, https://doi.org/10.1051/meca/2020079