DOI QR코드

DOI QR Code

Investigating the fatigue failure characteristics of A283 Grade C steel using magnetic flux detection

  • Arifin, A. (Department of Mechanical & Materials Engineering, Faculty of Engineering and Built Enviroments, Universiti Kebangsaan Malaysia) ;
  • Jusoh, W.Z.W. (Department of Mechanical & Materials Engineering, Faculty of Engineering and Built Enviroments, Universiti Kebangsaan Malaysia) ;
  • Abdullah, S. (Department of Mechanical & Materials Engineering, Faculty of Engineering and Built Enviroments, Universiti Kebangsaan Malaysia) ;
  • Jamaluddin, N. (Department of Mechanical & Materials Engineering, Faculty of Engineering and Built Enviroments, Universiti Kebangsaan Malaysia) ;
  • Ariffin, A.K. (Department of Mechanical & Materials Engineering, Faculty of Engineering and Built Enviroments, Universiti Kebangsaan Malaysia)
  • 투고 : 2014.12.26
  • 심사 : 2015.02.04
  • 발행 : 2015.09.25

초록

The Metal Magnetic Memory (MMM) method is a non-destructive testing method based on an analysis of the self-magnetic leakage field distribution on the surface of a component. It is used for determining the stress concentration zones or any irregularities on the surface or inside the components fabricated from ferrous-based materials. Thus, this paper presents the MMM signal behaviour due to the application of fatigue loading. A series of MMM data measurements were performed to obtain the magnetic leakage signal characteristics at the elastic, pre-crack and crack propagation regions that might be caused by residual stresses when cyclic loadings were applied onto the A283 Grade C steel specimens. It was found that the MMM method was able to detect the defects that occurred in the specimens. In addition, a justification of the Self Magnetic Flux Leakage patterns is discussed for demonstrating the effectiveness of this method in assessing the A283 Grade C steel under cyclic loadings.

키워드

참고문헌

  1. C33, A. (2004), Standard Specification for Concrete Aggregates; ASTM International, West Conshohocken, PA, USA.
  2. Changliang, S., Shiyun, D., Binshi, X. and Peng, H. (2010), "Stress concentration degree affects spontaneous magnetic signals of ferromagnetic steel under dynamic tension load", NDT & E International, 43(1), 8-12. https://doi.org/10.1016/j.ndteint.2009.08.002
  3. Dong, L., Xu, B., Dong, S., Chen, Q. and Dan, W. (2008), "Monitoring fatigue crack propagation of ferromagnetic materials with spontaneous abnormal magnetic signals", Int. J. Fatig., 30(9), 1599-1605. https://doi.org/10.1016/j.ijfatigue.2007.11.009
  4. Dong, L., Xu, B., Dong, S., Song, L., Chen, Q. and Wang, D. (2009), "Stress dependence of the spontaneous stray field signals of ferromagnetic steel", NDT & E International, 42(4), 323-327. https://doi.org/10.1016/j.ndteint.2008.12.005
  5. Dong, L., Xu, B., Dong, S. and Chen, Q. (2010), "Characterisation of stress concentration of ferromagnetic materials by metal magnetic memory testing", Nondestruct. Test. Eva., 25(2), 145-151. https://doi.org/10.1080/10589750902795366
  6. Dong, L.H., Xu, B.S., Wang, H.P. and Xue, N. (2012), "A physical model for self-emitting magnetic Signals during fatigue crack propagation", Appl. Mech. Mater., 190-191, 415-418. https://doi.org/10.4028/www.scientific.net/AMM.190-191.415
  7. Dubov, A.A. (1995), "Diagnostics of boiler tubes with usage of metal magnetic memory", Moscow: Energoatomizdat.
  8. Dubov, A. (2006), "Principle features of metal magnetic memory method and inspection tools as compared to known magnetic NDT methods", Can. Inst. Non-Destruct. Eva. (CINDE) J., 27(3), 16.
  9. Dubov, A. and Kolokolnikov, S. (2013), "The metal magnetic memory method application for online monitoring of damage development in steel pipes and welded joints specimens", Welding in the World, 57(1), 123-136. https://doi.org/10.1007/s40194-012-0011-5
  10. International, A. and Materials, A.S. for T.&. (2004), "Annual book of ASTM Standards", American Society for Testing & Materials.
  11. Jiles, D. (1998), Introduction to Magnetism and Magnetic Materials, CRC Press.
  12. Leng, J., Xu, M., Zhao, S. and Zhang, J. (2009), "Fatigue damage evaluation on ferromagnetic materials using magnetic memory method", Proceedings of 2009 International Conference on Measuring Technology and Mechatronics Automation, pp. 784-786.
  13. Li, J. and Xu, M. (2012), "Influence of uniaxial plastic deformation on surface magnetic field in steel", Meccanica, 47(1), 135-139. https://doi.org/10.1007/s11012-011-9424-2
  14. Li, J.W., Xu, M.Q., Leng, J.C. and Xu, M.X. (2010), "The characteristics of the magnetic memory signals under different states for Q235 defect samples", Adv. Mater. Res., 97-101, 500-503. https://doi.org/10.4028/www.scientific.net/AMR.97-101.500
  15. Lindgren, M. and Lepisto, T. (2001), "Effect of prestraining on Barkhausen noise vs. stress relation", NDT & E International, 34(5), 337-344. https://doi.org/10.1016/S0963-8695(00)00073-6
  16. Liu, C.K., Zhang, B., Chen, X., Ren, J.L., Tao, C.H. and He, Y.H. (2010), "Research on fatigue damage of ferromagnetic material by metal magnetic memory methods", Adv. Mater. Res., 97-101, 4501-4504. https://doi.org/10.4028/www.scientific.net/AMR.97-101.4501
  17. Wang, Z.D., Yao, K., Deng, B. and Ding, K.Q. (2010a), "Quantitative study of metal magnetic memory signal versus local stress concentration", NDT & E International, 43(6), 513-518. https://doi.org/10.1016/j.ndteint.2010.05.007
  18. Wang, Z.D., Yao, K., Deng, B. and Ding, K.Q. (2010b), "Theoretical studies of metal magnetic memory technique on magnetic flux leakage signals", NDT & E International, 43(4), 354-359. https://doi.org/10.1016/j.ndteint.2009.12.006
  19. Wang, H.P., Dong, L.H., Dong, S.Y., Xue, N. and Xu, B.S. (2012), "Characterization of stress concentration degree based on 2-dementional magnetic memory signals", Appl. Mech. Mater., 268-270, 396-400. https://doi.org/10.4028/www.scientific.net/AMM.268-270.396
  20. Wang, Z.D., Gu, Y. and Wang, Y.S. (2012), "A review of three magnetic NDT technologies", Journal of Magn. Magn. Mater., 324(4), 382-388. https://doi.org/10.1016/j.jmmm.2011.08.048
  21. Xing, H.Y., Wu, D.B. and Xu, M.Q. (2010), "Material fatigue behavior and its mechanism based on MMM technology", Adv. Mater. Res., 146-147, 408-411. https://doi.org/10.4028/www.scientific.net/AMR.146-147.408
  22. Yang, L.J., Liu, B., Chen, L.J. and Gao, S.W. (2013), "The quantitative interpretation by measurement using the magnetic memory method (MMM)-based on density functional theory", NDT & E International, 55, 15-20. https://doi.org/10.1016/j.ndteint.2013.01.002
  23. Yuan, J.J. and Zhang, W.M. (2011), "The surface weak magnetic signals of low carbon steel under cyclic loads", Adv. Mater. Res., 298, 197-202. https://doi.org/10.4028/www.scientific.net/AMR.298.197
  24. Zhang, Y.L., Gou, R.B., Li, J.M., Shen, G.T. and Zeng, Y.J. (2012), "Characteristics of metal magnetic memory signals of different steels in high cycle fatigue tests", Fatigue Fract. Eng. Mater. Struct., 35(7), 595-605. https://doi.org/10.1111/j.1460-2695.2012.01651.x