DOI QR코드

DOI QR Code

Numerical study on overall thermal performance in SAH duct with compound roughness of V-shaped ribs and dimples

V 형 rib과 dimple로 구성된 SAH 덕트에서의 총괄 열성능에 대한 수치적 연구

  • Kumar, Anil (School of Mechanical Engineering, Kyungpook National University) ;
  • Kim, Man-Hoe (School of Mechanical Engineering, Kyungpook National University)
  • Received : 2015.07.13
  • Accepted : 2015.08.25
  • Published : 2015.08.30

Abstract

This paper presents the thermal hydraulic performance of a three dimensional rib-roughened solar air heater (SAH) duct with the one principal wall subjected to uniform heat flux. The SAH duct has aspect ratio of 12.0 and the Reynolds number ranges from 2000 to 12000. The roughness has relative rib height of 0.045, ratio of dimple depth to print diameter of 0.5 and rib pitch ratio of 8.0. The flow attack angle is varied from $35^{\circ}$ to $70^{\circ}$. Various turbulent flow models are used for the heat transfer and fluid flow analysis and their results are compared with the experimental results for smooth surfaces. The computational fluid dynamics (CFD) results based on the renormalization k-epsilon model are in better outcomes compared with the experimental data. This model is used to calculate heat transfer and fluid flow in SAH duct with the compound roughness of V-shaped ribs and dimples. The overall thermal performance based on equal pumping power is found to be the highest (2.18) for flow attack angle of $55^{\circ}$. The thermo-hydraulic performance for V-pattern shaped ribs combined with dimple ribs is higher than that for dimple rib shape and V-pattern rib shape air duct.

Keywords

References

  1. A. Kumar, M.-H. Kim. Numerical optimization of solar air heaters having different types of roughness shapes on the heated plate - Technical note, Energy, Vol. 72, pp.731-738, 2014. https://doi.org/10.1016/j.energy.2014.05.100
  2. A. Kumar, R.P. Saini, J.S. Saini. A review of thermo-hydraulic performance of artificially roughened solar air heaters, Renewable and Sustainable Energy Review, Vol. 37, pp. 100-122, 2014. https://doi.org/10.1016/j.rser.2014.04.063
  3. A. Kumar, R.P. Saini, J.S. Saini. Heat and fluid flow characteristics of roughened solar air heater duct-A review, Renewable Energy, Vol. 47, pp. 77-94, 2012. https://doi.org/10.1016/j.renene.2012.04.001
  4. A. Kumar, R.P. Saini, J.S. Saini. Effect of roughness width ratio in discrete Multi v-shaped rib roughness on thermo-hydraulic performance of solar air heater, Heat and Mass Transfer, Vol. 51, pp. 209-220, 2015. https://doi.org/10.1007/s00231-014-1407-0
  5. A. Pundir, A. Kumar, Technical feasibility study for power generation from a potential mini hydro site nearby Shoolini University, Advances Energy Research, Vol. 4, pp. 85-95, 2014.
  6. A. Kumar. Analysis of heat transfer and fluid flow in different shaped roughness elements on the absorber plate solar air heater duct, Energy Procedia, Vol. 57, pp. 2102-2111, 2014. https://doi.org/10.1016/j.egypro.2014.10.176
  7. J.C. Han, L.R. Glicksman, W.M. Rohsenow. An investigation of heat transfer and friction for rib-roughened surfaces. Int. J. of Heat and Mass Transfer, Vol. 21, pp. 1143-1156, 1978. https://doi.org/10.1016/0017-9310(78)90113-8
  8. J.S. Park, J.C. Han, Y.Huang. Heat transfer performance comparisons of five different rectangular channels with parallel angled ribs. Int. J. of Heat and Mass Transfer, Vol. 35, pp. 2891-2903, 1992. https://doi.org/10.1016/0017-9310(92)90309-G
  9. S.C. Lau, R.D. Mcmillin, J.C. Han. Turbulent heat transfer and friction in a square channel with discrete rib turbulators. Journal of Turbomachinery, Vol. 113, pp. 360-367, 1991. https://doi.org/10.1115/1.2927884
  10. Y.M. Zhang, W.Z. Gu, J.C. Han. Heat transfer and friction in rectangular channels with ribbed or ribbed-grooved walls. Journal of Heat Transfer, Vol. 116, pp. 58-65, 1994. https://doi.org/10.1115/1.2910884
  11. K. Prasad, S.C. Mullick. Heat transfer characteristics of a solar air heater used for drying purposes. Applied Energy, Vol. 13, pp. 83-93, 1983. https://doi.org/10.1016/0306-2619(83)90001-6
  12. B.N. Prasad, J.S. Saini, Effect of artificial roughness on heat transfer and friction factor in a solar air heater. Solar Energy, Vol. 41, pp. 555-560, 1988. https://doi.org/10.1016/0038-092X(88)90058-8
  13. M.M. Sahu, J.L. Bhagoria, Augmentation of heat transfer coefficient by using $90^{\circ}$ broken transverse ribs on absorber plate of Solar air heater, Renewable Energy, Vol. 30, pp. 2075-2063, 2005. https://doi.org/10.1016/j.renene.2004.05.014
  14. R. Kiml, S. Mochizuki, A. Murata, Effects of rib arrangements on heat transfer and flow behaviour in a rectangular rib roughened passage Journal of Heat Transfer, Vol. 123, pp. 675-681, 2001. https://doi.org/10.1115/1.1378019
  15. D. Gupta, S.C. Solanki, J.S. Saini, Thermohydraulic performance of solar air heaters with roughened absorber plates, Solar Energy, Vol. 61, pp. 33-42, 1997. https://doi.org/10.1016/S0038-092X(97)00005-4
  16. H.H. Cho, Y.Y. Kim, D.H. Rhee, S.Y. Lee, S.J. Wu. The effect of gap position in discrete ribs on local heat/mass transfer in a square duct, Journal of Enhanced Heat Transfer, Vol. 10, pp. 287-300, 2003. https://doi.org/10.1615/JEnhHeatTransf.v10.i3.40
  17. K.R. Aharwal, B.K. Gandhi, J.S. Saini, Experimental investigation on heat-transfer enhancement due to a gap in an inclined continuous rib arrangement in a rectangular duct of solar air heater, Renewable Energy, Vol. 33, pp. 585-596, 2008. https://doi.org/10.1016/j.renene.2007.03.023
  18. J.C. Han, Y.M. Zhang, C.P. Lee, Influence of surface heat flux ratio on heat transfer augmentation in square channels with parallel, crossed and v-shaped angled ribs. Journal of Turbomachinery, Vol. 114, pp. 872-880, 1992. https://doi.org/10.1115/1.2928042
  19. R.T. Kukreja, S.C. Lau, R.D. McMillin, Local Heat/Mass transfer distribution in a square channel with full and V-shaped ribs. Int. J. of Heat and Mass Transfer, Vol. 36, pp. 2013-2020, 1993. https://doi.org/10.1016/S0017-9310(05)80132-2
  20. M.E. Taslim, T. Li. D.M. Krecher, Experimental heat transfer and friction in channel roughened with angled, v-shaped and discrete ribs on two opposite walls, Journal of Turbomachinery, Vol. 118, pp. 20-28, 1996. https://doi.org/10.1115/1.2836602
  21. L.M. Wright, W.L. Fu, J.C. Han, Thermal performance of angled, V-shaped and W-shaped rib turbulators in rotating rectangular cooling channels (AR=4:1), Journal of Turbomachinery, Vol. 126, pp. 604-614, 2004. https://doi.org/10.1115/1.1791286
  22. A.M.E. Momin, J.S. Saini, S.C. Solanki, Heat transfer and friction in solar air heater duct with v-shaped rib roughness on absorber plate. In.t. J of Heat and Mass Transfer, Vol. 45, pp. 3383-3396. 2002. https://doi.org/10.1016/S0017-9310(02)00046-7
  23. R.P. Saini, J. Verma, Heat transfer and friction factor correlations for a duct having dimple-shaped artificial roughness for solar air heaters. Energy, Vol. 133, pp. 1277-1287, 2008.
  24. A. Chaube, P.K. Sahoo, S.C. Solanki. Analysis of heat transfer augmentation and flow characteristics of a solar air heater. Renewable Energy, Vol. 31, pp. 317-331, 2006. https://doi.org/10.1016/j.renene.2005.01.012
  25. S. Kumar, R.P. Saini. CFD based performance analysis of a solar air heater duct provided with artificial roughness, Renewable Energy, Vol. 34, pp. 1285-1291, 2009. https://doi.org/10.1016/j.renene.2008.09.015
  26. R. Mehrdad, R. Arman, Prediction of turbulent flow and heat transfer in channels with array of detached and alternative attached-detached ribs, Int. J. of Numerical Methods for Heat & Fluid Flow, Vol. 19, pp. 266-284, 2009. https://doi.org/10.1108/09615530910938281
  27. S.V. Karmare, A.N. Tikekar. Analysis of fluid flow and heat transfer in a grit roughened surface solar air heater using CFD. Solar Energy, Vol. 84, pp. 409-417, 2010. https://doi.org/10.1016/j.solener.2009.12.011
  28. M. Oronzio, N. Sergio, R. Daniele. Numerical investigation of air forced convection in channels with differently shaped transverse ribs, Int. J. of Numerical Methods for Heat & Fluid Flow, Vol. 21, pp. 618-639, 2011. https://doi.org/10.1108/09615531111135864
  29. A.K. Sharma, N.S. Thakur. CFD based fluid flow and heat transfer analysis of a v-shaped roughened surface solar air heater. Int. J. of Engineering Science and Technology, Vol. 4, pp. 2115-2121, 2012.
  30. A. S. Yadav, J.L. Bhagoria, A numerical investigation of square sectioned transverse rib roughened solar air heater, Int. J. of Thermal Sciences, Vol. 79, pp. 111-131, 2014. https://doi.org/10.1016/j.ijthermalsci.2014.01.008
  31. M.J. Lewis. Optimizing the thermo-hydraulic performance of rough surfaces. Int. J. of Heat and Mass Transfer, Vol. 18, pp. 1243-1248, 1975. https://doi.org/10.1016/0017-9310(75)90232-X

Cited by

  1. Heat transfer enhancement in solar air channel with broken multiple V-type baffle vol.8, 2016, https://doi.org/10.1016/j.csite.2016.07.001
  2. Experimental study of enhancement of heat transfer and pressure drop in a solar air channel with discretized broken V-pattern baffle vol.101, 2017, https://doi.org/10.1016/j.renene.2016.09.033
  3. Numerical and experimental investigation of enhancement of heat transfer in dimpled rib heat exchanger tube 2017, https://doi.org/10.1007/s00231-017-2080-x
  4. Effect of square wings in multiple square perforated twisted tapes on fluid flow and heat transfer of heat exchanger tube vol.10, 2017, https://doi.org/10.1016/j.csite.2017.03.002
  5. A detailed review on various V-shaped ribs roughened solar air heater vol.55, pp.12, 2019, https://doi.org/10.1007/s00231-019-02656-4
  6. Empirical correlations development for heat transfer and friction factor of a solar rectangular air passage with spherical-shaped turbulence promoters vol.139, pp.2, 2015, https://doi.org/10.1007/s10973-019-08551-8