한국재료학회지 (Korean Journal of Materials Research)

  • 제25권8호
  • /
  • Pages.417-422
  • /
  • 2015
  • /
  • 1225-0562(pISSN)
  • /
  • 2287-7258(eISSN)
한국재료학회 (Materials Research Society of Korea)
권호 표지
DOI QR코드

DOI QR Code

아공석강의 충격인성 및 연성-취성 천이온도에 미치는 펄라이트 층상간격의 영향

Effect of Pearlite Interlamellar Spacing on Impact Toughness and Ductile-Brittle Transition Temperature of Hypoeutectoid Steels

  • 이상인 (서울과학기술대학교 신소재공학과) ;
  • 강준영 (서울과학기술대학교 신소재공학과) ;
  • 황병철 (서울과학기술대학교 신소재공학과)
  • Lee, Sang-In (Department of Materials Science and Engineering Seoul National University of Science and Technology) ;
  • Kang, Jun-Young (Department of Materials Science and Engineering Seoul National University of Science and Technology) ;
  • Hwang, Byoungchul (Department of Materials Science and Engineering Seoul National University of Science and Technology)
  • 투고 : 2015.07.17
  • 심사 : 2015.07.29
  • 발행 : 2015.08.27
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

In this study, low-carbon hypoeutectoid steels with different ferrite-pearlite microstructures were fabricated by varying transformation temperature. The microstructural factors such as pearlite fraction and interlamellar spacing, and cementite thickness were quantitatively measured and then Charpy impact tests conducted on the specimens in order to investigate the correlation of the microstructural factors with impact toughness and ductile-brittle transition temperature. The microstructural analysis results showed that the pearlite interlamellar spacing and cementite thickness decreases while the pearlite fraction increases as the transformation temperature decreases. Although the specimens with higher pearlite fractions have low absorbed energy, on the other hand, the absorbed energy is higher in room temperature than in low temperature. The upper-shelf energy slightly increases with decreasing the pearlite interlamellar spacing. However, the ductile-brittle transition temperature is hardly affected by the pearlite interlamellar spacing because there is an optimum interlamellar spacing dependent on lamellar ferrite and cementite thickness and because the increase in pearlite fraction and the decrease in interlamellar spacing with decreasing transformation temperature have a contradictory role on absorbed energy.

키워드

참고문헌

  1. C. M. Bae, C. S. Lee and W. J. Nam, Mater. Sci. Technol., 18(11), 1317 (2002). https://doi.org/10.1179/026708302225007556
  2. F. P. L. Kavishe and T. J. Baker, Mater. Sci. Technol., 2(8), 816 (1986). https://doi.org/10.1179/mst.1986.2.8.816
  3. B. E. O'Donnelly, R. L. Reuben and T. N. Baker, Met. Technol., 11(1), 45 (1984). https://doi.org/10.1179/030716984803274837
  4. F. B. Pickering and B. Garbarz, Scripta Metall., 21(3), 249 (1987). https://doi.org/10.1016/0036-9748(87)90207-9
  5. K. K. Ray and D. Mondal, Acta Metall. Mater., 39(10), 2201 (1991). https://doi.org/10.1016/0956-7151(91)90002-I
  6. C. M. Bae, W. J. Nam and C. S. Lee, Scripta Mater., 41(6), 605 (1999). https://doi.org/10.1016/S1359-6462(99)00200-6
  7. H. J. Sim, Y. B. Lee and W. J. Nam, J. Mater. Sci., 39(5), 1849 (2004). https://doi.org/10.1023/B:JMSC.0000016201.77933.c2
  8. J. M. Hyzak and I. M. Bernstein, Metall. Trans. A, 7A(8), 1217 (1976).
  9. K. Nakase and I. M. Bernstein, Metall. Trans. A, 19A(11), 2819 (1988).
  10. D. A. Porter, K. E. Easterling and M. Y. Sherif : Phase Transformations in Metals and Alloys, (Revised Reprint). CRC press, (2009).
  11. D. Cheetham and N. Ridley, Met. Sci., 9(9), 411 (1975).
  12. J. P. Houin, A. Simon and G. Beck, Trans. ISIJ, 21(10), 726 (1981). https://doi.org/10.2355/isijinternational1966.21.726
  13. T. Gladman, I. D. Mcivor and F. B. Pickering, J. Iron Steel Inst., 210(12), 916 (1972).
  14. Y. Ohmori and R. W. K. Honeyconbe, Trans. ISIJ, 11, 1160 (1971).
  15. K. W. Burns and F. B. Pickering, J. Iron Steel Inst., 202(11), 899 (1964).
  16. J. A. Rinebolt and W. J. Harris, Jr., Trans. A. S. M., 43, 1175 (1951).