DOI QR코드

DOI QR Code

Effect of Resistance Spot Welding Parameters on AA1100 Aluminum Alloy and SGACD Zinc coated Lap Joint Properties

  • Chantasri, Sakchai (Department of Industrial Engineering, Faculty of Engineering, Rajamangala University of Technology Thanyaburi) ;
  • Poonnayom, Pramote (Department of Industrial Engineering, Faculty of Engineering, Rajamangala University of Technology Thanyaburi) ;
  • Kaewwichit, Jesada (Department of Industrial Engineering, Faculty of Engineering, Rajamangala University of Technology Thanyaburi) ;
  • Roybang, Waraporn (Department of Industrial Engineering, Faculty of Engineering, Rajamangala University of Technology Thanyaburi) ;
  • Kimapong, Kittipong (Department of Industrial Engineering, Faculty of Engineering, Rajamangala University of Technology Thanyaburi)
  • 투고 : 2015.03.23
  • 심사 : 2015.05.21
  • 발행 : 2015.06.30

초록

This article is aimed to study the effects of resistance spot welding (RSW) on the lap joint properties between AA1100 aluminum alloy and SGACD zinc coated steel and its properties. The summarized experimental results are as follows. The summarized experimental results are as follows. The optimum welding parameters that produced maximum tensile shear strength of 2200 N was a welding current of 95 kA, a holding time of 10 cycles, and a welding pressure of 0.10 MPa. Increasing of welding current, increased the tensile shear strength of the joint and also increased the amount of aluminum dispersion at the joint interface. The lap joint of steel over the aluminum (Type I) showed the higher joint tensile shear strength than a lap joint of aluminum over the steel (Type II). The indentation depth and the ratio of the indentation depth to the plate thickness decreased when the welding current was increased in the type I lap joint and also decreased when the welding current was decreased in the type II lap joint. The interface structure showed the formation of the brittle $FeAl_3$ intermetallic compound that deteriorated the joint strength.

키워드

참고문헌

  1. Qiu, R., Shi, H., Zhang, K., Tu, Y., Iwamoto, C. and Satonaka, S., "Interfacial characterization of joint between mild steel and aluminum alloy welded by resistance spot welding," Materials Characterization, Vol. 61, pp. 684-688, 2010. https://doi.org/10.1016/j.matchar.2010.03.015
  2. Su, Y, Hua, X, Wu, Y., "Quatitative characterization of porosity in Fe-Al dissimilar materials lap joint made by gas metal arc welding with different current modes," Journal of Materials Processing Technology, Vol. 214, pp. 81-86, 2012.
  3. Zhang, H., Liu J., "Microstructure characteristics and mechanical property of aluminum alloy/stainless steel lap joint fabricated by MIG welding-brazing process," Materials Science and Engineering A.,Vol. 528, pp. 6179-6185, 2011. https://doi.org/10.1016/j.msea.2011.04.039
  4. Dehmolaei, R., Shamanian, M., Kermanpur A., "Microstructural characterization of dissimilar welds between alloy 800 and HP heat-resistant steel," Materials Characterization, Vol. 59, pp. 1447-1454, 2008. https://doi.org/10.1016/j.matchar.2008.01.013
  5. S. Kobayashi and T. Yakou, "Control of Interme tallic Compound Layers at Interface between Steel and Aluminum by diffusion-treatment," Materials Science and Engineering: A, Vol. 338, pp. 44-53, 2002. https://doi.org/10.1016/S0921-5093(02)00053-9
  6. Vural, M., Akkus, A. and Eryurek, B., "Effect of Welding nugget diameter on the fatigue strength of the resistance spot welded joints of different steel sheets," J. of Materials Processing Technology, Vol. 176, pp. 127-132, 2006. https://doi.org/10.1016/j.jmatprotec.2006.02.026
  7. Sun, X., Stephens, E.V., Khaleel, M.A., Shao, H. and Kimchi, M., "Resistance Spot Welding of Aluminum Alloy to Steel with Transition Materials - From Process to Performance - Part I: Experimental Study," Welding Journal, Vol. 84, No. 6, pp. 188-195, 2004.
  8. Qiu, R, Iwamoto, C. and Satonaka, S., "Interfacial microstructure and strength of steel/aluminum alloy joints welded by resistance spot welding with cover plate," J. of Materials Processing Technology, Vol. 209, pp. 4186-4193, 2009. https://doi.org/10.1016/j.jmatprotec.2008.11.003
  9. Qiu, R, Iwamoto, C. and Satonaka, S., "The Influence of reaction layer on the strength of aluminum/steel joint welded by resistance spot welding," Materials Characterization, Vol. 60, pp. 156-159, 2009. https://doi.org/10.1016/j.matchar.2008.07.005
  10. Qiu, R., Shi, H., Zhang, K., Tu, Y., Iwamoto, C. and Satonaka, S., "Interfacial characterization of joint between mild steel and aluminum alloy welded by resistance spot welding," Materials Characterization, Vol. 61, pp. 684-688, 2010. https://doi.org/10.1016/j.matchar.2010.03.015
  11. Qiu, R, Satonaka, S. and Iwamoto, C., "Effect of interfacial reaction layer on tensile strength of resistance spot welded joints between aluminum alloy and steels," Materials and design, Vol. 30, pp. 3686-3689, 2009. https://doi.org/10.1016/j.matdes.2009.02.012
  12. JIS Z3139 (1978), Method of Macro Test for Section of Spot Welded Joint, JIS Handbook of Welding, Tokyo, Japanese Industrial Standard Association, 1997.
  13. Kobayashi, S., Yakou, T., "Control of Intermetallic Compound Layers at Interface between Steel and Aluminum by Diffusion-treatment," Materials Science and Engineering A, Vol. 338, pp. 44-53, 2002. https://doi.org/10.1016/S0921-5093(02)00053-9

피인용 문헌

  1. Tensile and Fatigue Behaviour of AA6022-T4 to IF Steel Resistance Spot Welds vol.5, 2017, https://doi.org/10.1016/j.prostr.2017.07.207