DOI QR코드

DOI QR Code

Influence of intake runner cross section design on the engine performance parameters of a four stroke, naturally aspirated carbureted SI engine

  • Received : 2015.02.10
  • Accepted : 2015.04.20
  • Published : 2015.06.30

Abstract

The current scenario of the transportation sector reflects the urgent need to address issues such as depletion of traditional fuel reserves and ever growing pollution levels. Researchers around the world are focussing on alternatives as well as optimisation of currently employed devices to reduce the pollution levels generated by the commonly used fuels. One such optimisation involves the study of air flow within the intake manifolds of SI engines. It is a well-known fact that alterations in the air manifolds of engines have a significant impact on the engine performance parameters, fuel consumption and emission levels. Previous works have demonstrated the impacts of runner lengths, diameter, plenum volume, taper angle of distribution manifolds and other factors on in-cylinder fluid motion and engine performance. However, a static setup provides an optimal configuration only at a specific engine speed. This paper aims to investigate the variations in the same parameters on a four stroke, naturally aspirated single cylinder SI engine through varying the cross section design over the intake runner with the aid of Computational Fluid Dynamics. The system consists of segments that form the intake runner with projections on the inside that allow various permutations of the intake runner segments. The various configurations provide the optimised fluid flow characteristics within the intake manifold at specific engine speed intervals. The variations such as turbulence, air fuel mixing are analysed using the three dimensional CFD software FLUENT. The results can be used further for developing an automated or manually adjustable intake manifold.

Keywords

References

  1. Ugur Kesgin, "Study on the design of inlet and exhaust system of a stationary internal combustion engine," Energy Conversion and Management, Vol. 46, Issues 13-14, pp. 2258-2287, August 2005, , ISSN 0196-8904, http://dx.doi.org/10.1016/j.enconman.2004.10.015.
  2. Mohamed Ali Jemni, Gueorgui Kantchev, Mohamed Salah Abid, "Influence of intake manifold design on in-cylinder flow and engine performances in a bus diesel engine converted to LPG gas fuelled, using CFD analyses and experimental investigations," Energy, Vol. 36, Issue 5, pp. 2701-2715, May 2011, ISSN 0360-5442, http://dx.doi.org/10.1016/j.energy.2011.02.011.
  3. A.S Green, T Moumtzis, "Case study: use of inlet manifold design techniques for combustion applications," Applied Thermal Engineering, Vol. 22, Issue 13, pp. 1519-1527, September 2002, ISSN 1359-4311, http://dx.doi.org/10.1016/S1359-4311(02)00070-4.
  4. Jimmy C.K. Tong, Ephraim M. Sparrow, John P. Abraham, "Geometric strategies for attainment of identical outflows through all of the exit ports of a distribution manifold in a manifold system," Applied Thermal Engineering, Vol. 29, Issues 17-18, pp. 3552-3560, December 2009, ISSN 1359-4311, http://dx.doi.org/10.1016/j.applthermaleng.2009.06.010.
  5. Junye Wang, "Theory of flow distribution in manifolds," Chemical Engineering Journal, Vol. 168, Issue 3, pp. 1331-1345, April 15, 2011, ISSN 1385-8947, http://dx.doi.org/10.1016/j.cej.2011.02.050.
  6. S. A. Sulaiman, S. H. M. Murad, I. Ibrahim and Z. A. Abdul Karim, STUDY OF FLOW IN AIR-INTAKE SYSTEM FOR A SINGLE-CYLINDER GO-KART ENGINE
  7. M.A. Ceviz, M. Akin, "Design of a new SI engine intake manifold with variable length plenum," Energy Conversion and Management, Vol. 51, Issue 11, pp. 2239-2244, November 2010, ISSN 0196-8904, http://dx.doi.org/10.1016/j.enconman.2010.03.018.
  8. Pulkrabek, Engineering Fundamentals of the Internal Combustion Engine
  9. Heywood, Internal Combustion Engine Fundamentals