KSCE Journal of Civil and Environmental Engineering Research (대한토목학회논문집)

Korean Society of Civil Engeneers (대한토목학회)
권호 표지
DOI QR코드

DOI QR Code

An Indeterminate Strut-Tie Model for Prestressed Concrete Beams

프리스트레스트 콘크리트 보의 부정정 스트럿-타이 모델

  • 채현수 (경북대학교 BK21플러스 친환경융합건설기술인력사업단) ;
  • 윤영묵 (경북대학교 토목공학과)
  • Received : 2014.12.13
  • Accepted : 2015.06.13
  • Published : 2015.08.01
Download PDF
⟨ Previous Next ⟩

Abstract

In this study, a statically simple indeterminate strut-tie model is proposed for the rational analysis and design of simply supported prestressed concrete beams by reflecting all characteristics of nonlinear structural behavior and load transfer mechanisms. In addition, a load distribution ratio that allows to transform the proposed indeterminate strut-tie model to a determinate model is also suggested to help structural designers conduct the structural analysis and design of simply supported prestressed concrete beams by using the strut-tie model method of current design codes. For verifying of the validity of the proposed model and load distribution ratio, the ultimate strengths of 47 simply supported prestressted concrete beams tested to failure were estimated and the results were compared with those by the strut-tie model methods of current design codes.

이 논문에서는 스트럿-타이 모델을 이용한 프리스트레스트 콘크리트 보의 해석 및 설계 시 프리스트레스트 콘크리트 보의 비선형 파괴거동 특성 및 복잡한 하중전달 메커니즘을 합리적인 방법으로 반영할 수 있는 단순한 형태의 부정정 스트럿-타이 모델을 제안하였다. 또한 현행 설계기준서의 스트럿-타이 모델 규정을 이 연구에서 제안한 부정정 스트럿-타이 모델에 접목시켜 프리스트레스트 콘크리트 보의 해석 및 설계를 수행할 수 있는 부정정 스트럿-타이 모델의 하중분배율을 제안하였다. 이 연구에서 제안한 부정정 스트럿-타이 모델 및 하중분배율의 적합성을 검증하기 위해 파괴실험이 수행된 47개의 프리스트레스트 콘크리트 보의 극한강도를 평가하였으며, 그 결과를 현행 설계기준서의 스트럿-타이 모델 방법에 의한 평가결과와 비교분석 하였다.

Keywords

References

  1. ACI Subcommittee 445 (2002). Examples for the design of structural concrete with strut-and-tie models, Special Publication SP-208, American Concrete Institute, Farmington Hills, Michigan, USA.
  2. ACI-ASCE Committee 445 (2010). Further examples for the design of structural concrete with strut-and-tie models; SP-273, American Concrete Institute, Farmington Hills, Michigan, USA.
  3. Alshegeir, A. and Ramirez, J. A. (1992). "Strut-tie approach in pretensioned deep beams." ACI Structural Journal, Vol. 89, No. 3, pp. 296-304.
  4. American Association of State Highway and Transportation Officials (2010). AASHTO LRFD bridge design specifications, 5th Edition, Washington D.C., USA.
  5. American Concrete Institute (2014). Building code requirements for structural concrete (ACI 318-14) and commentary, Farmington Hills, Michigan, USA.
  6. Canadian Standards Association (2004). Design of concrete structures for buildings, CSA A23.3-M04, Rexdale, Ontario, Canada.
  7. Chae, H. S. and Yun, Y. M. (2015). "Strut-tie models and load distribution ratios for reinforced concrete deep beams with shear span-to-effective depth ratio of less than 3.0 - (I) Models and Load Distribution Ratios." Journal of the Korean Concrete Institute, KCI, In Review (in Korean).
  8. Comite Euro-International du Beton (2010). CEP-FIP model code 2010, International Federation for Structural Concrete (fib), Lausanne, Switzerland.
  9. Foster, S. J. and Gilbert, R. I. (1998). "Experimental studies on high-strength concrete deep beams." ACI Structural Journal, Vol. 95, No. 4, pp. 382-390.
  10. Jeon, C. H. and Yun, Y. M. (2010). "Validity evaluation fo effective strength of concrete strut using strut-tie model analysis of structural concrete." Journal of the Korean Society of Civil Engineers, Vol. 30, No. 5, pp. 443-462 (in Korean).
  11. Kaufman, M. K. and Ramirez, J. A. (1988). "Re-evaluation of the ultimate shear behavior of high-strength concrete prestressed I-beams." ACI Sturctural Journal, Vol. 85, No. 3, pp. 295-303.
  12. Pang, X. B. and Hsu, T. T. C. (1995). "Behavior of reinforced concrete membrane elements in shear." ACI Structural Journal, Vol. 92, No. 6, pp. 665-679.
  13. Ramirez, J. A. (1994). "Strut-tie design of pretensioned concrete members." ACI Structural Journal, Vol. 91, No. 4, pp. 572-578.
  14. Saqan, E. I. and Frosch, R. J. (2009). "Influence of flexural reinforcement on shear strength of prestressed concrete beams." ACI Structural Journal, Vol. 106, No. 7, pp. 60-68.
  15. Shahawy, M. A. and Batchelor, B. D. (1996). "Shear behavior of full-scale prestressed concrete girders: Comparison Between AASHTO Specifications and LRFD Code." PCI Journal, Vol. 41, No. 3, pp. 48-62. https://doi.org/10.15554/pcij.05011996.48.62
  16. Shahawy, M. A. and Cai, C. S. (1999). "A new approach to shear design of prestressed concrete members." PCI Journal, Vol. 44, No. 4, pp. 92-117.
  17. Tan, K. H. and Mansur, M. A. (1992). "Partial prestressing in concrete corbels and deep beams." ACI Structural Journal, Vol. 89, No. 3, pp. 251-262.
  18. Tan, K. H., Tong, K. and Tang, C. Y. (2001). "Direct strut-and-tie model for prestressed deep beams." Journal of Structural Engineering, ASCE, Vol. 127, No. 9, pp. 1076-1084. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:9(1076)
  19. Yun, Y. M. (2005). "Effective strength of concrete strut in strut-tie model (I): Methods for Determining Effective Strength of Concrete Strut." Journal of the Korean Society of Civil Engineers, Vol. 25, No. 1, pp. 49-59 (in Korean).
  20. Yun, Y. M. and Lee, W. S. (2005). "Nonlinear strut-tie model analysis of pre-tensioned concrete deep beams." Journal of Advances in Structural Engineering, Vol. 8, No. 1, pp. 85-98. https://doi.org/10.1260/1369433053749616