Earthquakes and Structures

  • 제8권3호
  • /
  • Pages.665-679
  • /
  • 2015
  • /
  • 2092-7614(pISSN)
  • /
  • 2092-7622(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Effect of loading velocity on the seismic behavior of RC joints

  • Wang, Licheng (State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology) ;
  • Fan, Guoxi (State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology) ;
  • Song, Yupu (State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology)
  • 투고 : 2014.01.14
  • 심사 : 2014.07.13
  • 발행 : 2015.03.25
⟨ 이전 논문 다음 논문 ⟩

초록

The strain rate of reinforced concrete (RC) structures stimulated by earthquake action has been generally recognized as in the range from $10^{-4}/s$ to $10^{-1}/s$. Because both concrete and steel reinforcement are rate-sensitive materials, the RC beam-column joints are bound to behave differently under different strain rates. This paper describes an investigation of seismic behavior of RC beam-column joints which are subjected to large cyclic displacements on the beam ends with three loading velocities, i.e., 0.4 mm/s, 4 mm/s and 40 mm/s respectively. The levels of strain rate on the joint core region are correspondingly estimated to be $10^{-5}/s$, $10^{-4}/s$, and $10^{-2}/s$. It is aimed to better understand the effect of strain rates on seismic behavior of beam-column joints, such as the carrying capacity and failure modes as well as the energy dissipation. From the experiments, it is observed that with the increase of loading velocity or strain rate, damage in the joint core region decreases but damage in the plastic hinge regions of adjacent beams increases. The energy absorbed in the hysteresis loops under higher loading velocity is larger than that under quasi-static loading. It is also found that the yielding load of the joint is almost independent of the loading velocity, and there is a marginal increase of the ultimate carrying capacity when the loading velocity is increased for the ranges studied in this work. However, under higher loading velocity the residual carrying capacity after peak load drops more rapidly. Additionally, the axial compression ratio has little effect on the shear carrying capacity of the beam-column joints, but with the increase of loading velocity, the crack width of concrete in the joint zone becomes narrower. The shear carrying capacity of the joint at higher loading velocity is higher than that calculated with the quasi-static method proposed by the design code. When the dynamic strengths of materials, i.e., concrete and reinforcement, are directly substituted into the design model of current code, it tends to be insufficiently safe.

키워드

과제정보

연구 과제 주관 기관 : Central Universities

참고문헌

  1. Asprone, D., Frascadore, R. and Ludovico, M.D. (2012), "Influence of strain rate on the seismic response of RC structures", Eng. Struct., 35(2), 29-36. https://doi.org/10.1016/j.engstruct.2011.10.025
  2. Bischoff, P.H. and Perry, S.H. (1991), "Compression behavior concrete at high strain rate", Mater. Struct., 24(11), 425-445. https://doi.org/10.1007/BF02472016
  3. Boyce, B.L. and Dilmore, M.F. (2009), "The dynamic tensile behavior of tough, ultrahigh-strength steels at strain-rates from 0.0002s-1 to 200s-1", Int. J. Impact Eng., 36(2), 263-271. https://doi.org/10.1016/j.ijimpeng.2007.11.006
  4. CEB-FIP Model Code (1990, 1991), Comite Euro-International du Beton.
  5. Cusatis, G. (2011), "Strain-rate effects on concrete behavior", Int. J. Impact Eng., 38(4), 162-170. https://doi.org/10.1016/j.ijimpeng.2010.10.030
  6. Fu, J.P. (2002), "Seismic behavior and design of joints in a reinforced concrete frame", Ph.D. Dissertation, Chongqing University.
  7. GB50010 (2010), Code for design of concrete structures, Construction Ministry of China.
  8. Ghobarah, A. and Biddah, A., (1999), "Dynamic analysis of reinforced concrete frames including joint shear deformation", Eng. Struct., 21(11), 971-987. https://doi.org/10.1016/S0141-0296(98)00052-2
  9. Hakuto, S., Park, R. and Tanaka, H. (2000), "Seismic load test on interior and exterior beam-column joints with substandard reinforcing details", ACI Struct. J., 97(1), 11-24.
  10. Hasan, A.S.M.Z., Hamid, R. and Ariffin, A.K. (2010), "Stress-strain behavior of normal strength concrete subjected to high strain rate", Asian J. Appl. Sci., 3(2), 145-152. https://doi.org/10.3923/ajaps.2010.145.152
  11. Isaac, P., Darby, A., Ibell, T. and Evernden, M. (2013), "Influence of loading rate on failure mode of reinforced concrete members", Proc. ICE-Eng. Comput. Mech., 166(4), 194-203. https://doi.org/10.1680/eacm.12.00002
  12. Lee, W.S. and Lin, C.F. (1998), "Plastic deformation and fracture behaviour of Ti-6Al-4V alloy loaded with high strain rate under various temperatures", Mater. Sci. Eng., ASCE, 241(1-2), 48-59. https://doi.org/10.1016/S0921-5093(97)00471-1
  13. Lee, W.S., Shyu, J.C. and Chiou, S.T. (2000), "Effect of strain rate on the impact response and dislocation substructure of 6061-T6 aluminum alloy", Scripta Materialia, 42, 51-56.
  14. Li, M. and Li, H.N. (2012), "Effects of strain rate on reinforced concrete structure under seismic loading", Adv. Struct. Eng., 15(3), 461-475. https://doi.org/10.1260/1369-4332.15.3.461
  15. Li, B. and Tran, C.T.N. (2009), "Seismic behaviour of reinforced concrete beam-column joints with vertical distributed reinforcement", ACI Struct. J., 106(6), 790-799.
  16. Li, B., Tran, C.T.N. and Pan, T.C. (2009), "Experimental and numerical investigations on the seismic performance of lightly reinforced concrete joints", J. Struct. Eng., ASCE, 135(9), 1007-1018. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000040
  17. Lu, X., Urukap, T.H., Li, S. and Lin, F. (2012), "Seismic behavior of interior RC beam-column joints with additional bars under cyclic loading", Earthq. Struct., 3(1), 37-57. https://doi.org/10.12989/eas.2012.3.1.037
  18. Malvar, L.J. and Ross, C.A. (1998), "Review of strain rate effects of concrete in tension", ACI Mater. J., 95(6), 735-739.
  19. Manjoine, M.J. (1944), "Influence of rate of strain and temperature on yield stress of mild steel", J. Appl. Mech., 11, 211-218.
  20. Martinez, J.A.R., Rusinek, A. and Klepaczko, J.R. (2009), "Constitutive relation for steels approximating quasi-static and intermediate strain rates at large deformations", Mech. Res. Comun., 36(4), 419-427. https://doi.org/10.1016/j.mechrescom.2008.12.001
  21. Meas, K., Li, B. and Pham, T.P. (2014), "Experimental and Numerical Studies on the Seismic Performance of RC Interior Beam-Column Joints", Adv. Struct. Eng., 17(2), 233-247. https://doi.org/10.1260/1369-4332.17.2.233
  22. Mukai, T., Ishikawa, K. and Higashi, K. (1995), "Influence of strain rate on the mechanical properties in fine-grained aluminum alloy", Mater. Sci. Eng., ASCE, 204(1-2), 12-18. https://doi.org/10.1016/0921-5093(95)09929-8
  23. Shah, S.P., Wang, M.L. and Chung, L. (1987), "Model concrete beam-column joints subjected to cyclic loading at two rates", Mater. Struct., 20(2), 85-95. https://doi.org/10.1007/BF02472743
  24. Sharma, A., Eligehausen, R. and Reddy, G. (2011), "A new model to simulate joint shear behavior of poorly detailed beam-column connections in RC structures under seismic loads, Part I: exterior joints", Eng. Struct., 33(3), 1034-1051. https://doi.org/10.1016/j.engstruct.2010.12.026
  25. Sun, H.B., Yoshida, F. and Ohmori, M. (2003), "Effect of strain rate on Lüders band propagating velocity and Luders strain for annealed mild steel under uniaxial tension", Mater. Lett., 57(29), 4535-4539. https://doi.org/10.1016/S0167-577X(03)00358-6
  26. Takeda, J.I. (1984), "Dynamic fracture of concrete structures due to severe earthquakes and some consideration on countermeasures", Proceedings of the 8th World Conference on Earthquake Engineering, San Francisco, California, USA.
  27. Yadar, S. and Ramesh, K.T. (1995), "The mechanical properties of tungsten-based composites at very high strain rates", Mater. Sci. Eng., ASCE, 203(1-2), 140-153. https://doi.org/10.1016/0921-5093(95)09865-8

피인용 문헌

  1. Numerical analysis of hysteretic behavior for RAC structure under earthquake loading vol.18, pp.4, 2019, https://doi.org/10.1080/13467581.2019.1645671
  2. Dynamic Behavior of a Precast and Partial Steel Joint under Various Shear Span-to-Depth Ratios vol.14, pp.9, 2021, https://doi.org/10.3390/ma14092162