DOI QR코드

DOI QR Code

Non-uniform shrinkage in simply-supported composite steel-concrete slabs

  • Al-Deen, Safat (School of Engineering and Information Technology, UNSW Canberra at the Australian Defence Force Academy) ;
  • Ranzi, Gianluca (School of Civil Engineering, The University of Sydney) ;
  • Uy, Brian (Centre for Infrastructure Engineering & Safety, School of Civil and Environmental Engineering, UNSW Australia)
  • 투고 : 2012.05.24
  • 심사 : 2014.06.11
  • 발행 : 2015.02.25

초록

This paper presents the results of four long-term experiments carried out to investigate the time-dependent behaviour of composite floor slabs with particular attention devoted to the development of non-uniform shrinkage through the slab thickness. This is produced by the presence of the steel deck which prevents moisture egress to occur from the underside of the slab. To observe the influence of different drying conditions on the development of shrinkage, the four 3.3 m long specimens consisted of two composite slabs cast on Stramit Condeck $HP^{(R)}$ steel deck and two reinforced concrete slabs, with the latter ones having both faces exposed for drying. During the long-term tests, the samples were maintained in a simply-supported configuration subjected to their own self-weight, creep and shrinkage for four months. Separate concrete samples were prepared and used to measure the development of shrinkage through the slab thickness over time for different drying conditions. A theoretical model was used to predict the time-dependent behaviour of the composite and reinforced concrete slabs. This approach was able to account for the occurrence of non-uniform shrinkage and comparisons between numerical results and experimental measurements showed good agreement. This work highlights the importance of considering the shrinkage gradient in predicting shrinkage deformations of composite slabs. Further comparisons with experimental results are required to properly validate the adequacy of the proposed approach for its use in routine design.

키워드

참고문헌

  1. A-H Eldib, M.E., Maaly, H.M., Beshay, A.W. and Tolba, M.T. (2009), "Modelling and analysis of two-way composite slabs", J. Constr. Steel Res., 65(5), 1236-1248. https://doi.org/10.1016/j.jcsr.2009.01.002
  2. Abdullah, R. and Easterling, S.W. (2009), "New evaluation and modeling procedure for horizontal shear bond in composite slabs", J. Constr. Steel Res., 65(4), 891-899. https://doi.org/10.1016/j.jcsr.2008.10.009
  3. Airumyan, E., Belyaev, V., and Rumyancev, I. (1990), "Efficient embossment for corrugated steel sheeting", IABSE Symposium on Mixed Structures Including New Materials, Brussels, Belgium, September.
  4. Al-deen, S., Ranzi, G. and Vrcelj, Z. (2011a), "Full-scale long-term experiments of simply-supported composite beams with solid slabs", J. Constr. Steel Res., 67(3), 308-321. https://doi.org/10.1016/j.jcsr.2010.11.001
  5. Al-deen, S., Ranzi, G. and Vrcelj, Z. (2011b), "Full-scale long-term and ultimate experiments of simply-supported composite beams with steel deck", J. Constr. Steel Res., 67(10), 1658-1676. https://doi.org/10.1016/j.jcsr.2011.04.010
  6. Al-Deen, S., Ranzi, G. and Vrcelj, Z. (2012), "Long-term experiments of composite beams and connections", Mag. Concrete Res., 64(9), 849-861. https://doi.org/10.1680/macr.10.00189
  7. Alsamsam, I. (1991), "Serviceability criteria for composite floor systems", Ph.D. Thesis, The University of Minnesota, Minneapolis, MN, USA.
  8. AS3600 (2009), AS3600-2009 Concrete Structures, Standards Australia.
  9. Bazant, Z.P. (1972), "Prediction of concrete creep effects using age-adjusted effective modulus method", ACI J., 69(4), 212-217.
  10. Bazant, Z.P. and Oh, B.H. (1984), "Deformation of progressively cracking reinforced concrete beams", ACI J., 81(3), 268-278.
  11. Bradford, M.A. (2010), "Generic modelling of composite steel-concrete slabs subjected to shrinkage, creep and thermal strains including partial interaction", Eng. Struct., 32(5), 1459-1465. https://doi.org/10.1016/j.engstruct.2010.01.024
  12. Bradford, M.A. and Gilbert, R.I. (1991), "Time-dependent behaviour of simply-supported steel-concrete composite beams", Mag. Concrete Res., 43(157), 265-274. https://doi.org/10.1680/macr.1991.43.157.265
  13. CEB (1984), CEB Design manual on structural effects of time-dependent behaviour of concrete, Georgi Publishing, Saint-Saphorin, Switzerland.
  14. Chen, S. and Shi, X. (2011), "Shear bond mechanism of composite slabs - A universal FE approach", J. Constr. Steel Res., 67(10), 1475-1484. https://doi.org/10.1016/j.jcsr.2011.03.021
  15. Chen, S., Shi, X. and Qiu, Z. (2011), "Shear bond failure in composite slabs- a detailed experimental study", Steel Compos. Struct., Int. J., 11(3), 233-250. https://doi.org/10.12989/scs.2011.11.3.233
  16. Crisinel, M. and Marimon, F. (2004), "A new simplified method for the design of composite slabs", J. Constr. Steel Res., 60(3-5), 481-491. https://doi.org/10.1016/S0143-974X(03)00125-1
  17. Daniels, B.J. and Crisinel, M. (1993), "Composite slab behavior and strength analysis. Part II: Comparisons with test results and parametric analysis", J. Struct. Eng., 119(1), 36-49. https://doi.org/10.1061/(ASCE)0733-9445(1993)119:1(36)
  18. Easterling, W.S. and Young, C.S. (1992), "Strength of composite slabs", J. Struct. Eng., 118(9), 2370-2389. https://doi.org/10.1061/(ASCE)0733-9445(1992)118:9(2370)
  19. Fan, J., Nie, J., Li, Q. and Wang, H. (2010), "Long-term behavior of composite beams under positive and negative bending. I: Experimental study", J. Struct. Eng., 136(7), 849-857. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000175
  20. Gholamhoseini, A., Gilbert, R.I., Bradford, M.A. and Chang, Z.T. (2012), "Long-term deformation of composite concrete slabs", Concrete in Australia, 38(8), 25-32.
  21. Gilbert, R.I. and Ranzi, G. (2011), Time-Dependent Behaviour of Concrete Structures, Spon Press, London, UK.
  22. Gilbert, R.I., Bradford, M.A., Gholamhoseini, A. and Chang, Z.T. (2012), "Effects of shrinkage on the long-term stresses and deformations of composite concrete slabs", Eng. Struct., 40, 9-19. https://doi.org/10.1016/j.engstruct.2012.02.016
  23. Jeong, Y.-J., Kim, H.-Y. and Kim, S.-H. (2005), "Partial-interaction analysis with push-out tests", J. Constr. Steel Res., 61(9), 1318-1331. https://doi.org/10.1016/j.jcsr.2005.01.010
  24. Johnson, R.P. (1987), "Shrinkage induced curvature in composite beams with a cracked concrete flange", Struct. Eng., 65B(4), 72-76.
  25. Kim, H.-Y. and Jeong, Y.-J. (2010), "Ultimate strength of a steel-concrete composite bridge deck slab with profiled sheeting", Eng. Struct., 32(2), 534-546. https://doi.org/10.1016/j.engstruct.2009.10.014
  26. Lopes, E. and Simoes, R. (2008), "Experimental and analytical behaviour of composite slabs", Steel Compos. Struct., Int. J., 8(5), 361-388. https://doi.org/10.12989/scs.2008.8.5.361
  27. Marimuthu, V., Seetharaman, S., Arul Jayachandran, S., Chellappan, A., Bandyopadhyay, T.K. and Dutta, D. (2007), "Experimental studies on composite deck slabs to determine the shear-bond characteristic values of the embossed profiled sheet", J. Constr. Steel Res., 63(6), 791-803. https://doi.org/10.1016/j.jcsr.2006.07.009
  28. Onesteel (2012), http://www.onesteel.com/
  29. Patrick, M. and Bridge, R.Q. (1994), "Partial shear connection design of composite slabs", Eng. Struct., 16(5), 348-362. https://doi.org/10.1016/0141-0296(94)90028-0
  30. Patrick, M. and Poh, K.W. (1990), "Controlled test for composite slab design parameters", IABSE Symposium on Mixed Structures Including New Materials, Brussels, Belgium, September.
  31. Porter, M.L. (1985), "Analysus of two-way acting composite", J. Struct. Eng., 111(1), 1-18. https://doi.org/10.1061/(ASCE)0733-9445(1985)111:1(1)
  32. Porter, M.L. and Ekberg Jr., C.E. (1977), "Behavior of steel-deck-reinforced slabs", J. Struct. Div., ASCE, 103(3), 663-677.
  33. Ranzi, G. and Vrcelj, Z. (2009), "Closed form solutions for the long-term analysis of composite steel-concrete members subjected to non-uniform shrinkage distributions", Proceedings of the Sixth International Conference on Advances in Steel Structures, Hong Kong, December.
  34. Ranzi, G., Al-deen, S., Ambrogi, L. and Uy, B. (2013a), "Long-term behaviour of simply-supported post-tensioned composite slabs", J. Constr. Steel Res., 88, 172-180. https://doi.org/10.1016/j.jcsr.2013.05.010
  35. Ranzi, G., Leoni, G. and Zandonini, R. (2013b), "State of the art on the time-dependent behaviour of composite steel-concrete structures", J. Constr. Steel Res., 80, 252-263. https://doi.org/10.1016/j.jcsr.2012.08.005
  36. Roll, F. (1971), "Effects of differential shrinkage and creep on a composite steel-concrete structure", ACI Special Publication, SP-27(8), 187-214.
  37. Seres, N. and Dunai, L. (2011), "Experimental and numerical studies on concrete encased embossments of steel strips under shear action for composite slabs with profiled steel decking", Steel Compos. Struct., Int. J., 11(1), 39-58.
  38. Stark, J.W.B. and Brekelmans, J.W.P.M. (1990), "Plastic design of continuous composite slabs", J. Constr. Steel Res., 15(1-2), 23-47. https://doi.org/10.1016/0143-974X(90)90041-E
  39. Stramit (2012), www.stramit.com.au
  40. Uy, B. (1997), "Long-term service load behaviour of simply-supported profiled composite slabs", Structures and Buildings, Proceedings of the Institution of Civil Engineers, 122(2), 193-208. https://doi.org/10.1680/istbu.1997.29309
  41. Veljkovic, M. (1996), "Behaviour and resistance of composite slabs", Ph.D. Theiss, Lulea University of Technology, Lulea, Sweden.
  42. Veljkovic, M. (1998), "Influence of load arrangement on composite slab behaviour and recommendations for design", J. Constr. Steel Res., 45(2), 149-178. https://doi.org/10.1016/S0143-974X(97)00055-2
  43. Wright, H.D., Vitek, J.L. and Rakib, S.N. (1992), "Long-term creep and shrinkage in composite beams with partial connection", ICE Proceedings, Structures and Buildings, 94(2), 187-195. https://doi.org/10.1680/istbu.1992.18787

피인용 문헌

  1. Long-term behaviour of simply supported composite slabs with recycled coarse aggregate vol.68, pp.24, 2016, https://doi.org/10.1680/jmacr.16.00090
  2. 08.61: A new approach for the serviceability limit state design of composite steel-concrete slabs vol.1, pp.2-3, 2017, https://doi.org/10.1002/cepa.281
  3. Long-term behaviour of simply-supported steel-bars truss slabs with recycled coarse aggregate vol.116, 2016, https://doi.org/10.1016/j.conbuildmat.2016.04.150
  4. Long-term structural analysis and stability assessment of three-pinned CFST arches accounting for geometric nonlinearity vol.20, pp.2, 2016, https://doi.org/10.12989/scs.2016.20.2.379
  5. Service design approach for composite steel–concrete floors vol.171, pp.1, 2018, https://doi.org/10.1680/jstbu.16.00196
  6. Effects of non-uniform shrinkage on the long-term behaviour of composite steel-concrete slabs vol.15, pp.2, 2015, https://doi.org/10.1007/s13296-015-6012-7
  7. Experimental investigation of longitudinal shear behavior for composite floor slab vol.23, pp.3, 2015, https://doi.org/10.12989/scs.2017.23.3.351
  8. Influence of post-pouring joint on long-term performance of steel-concrete composite beam vol.28, pp.1, 2015, https://doi.org/10.12989/scs.2018.28.1.039
  9. Assessment of design codes for the in-service behaviour of steel-concrete composite slabs vol.14, pp.5, 2015, https://doi.org/10.1590/s1983-41952021000500001
  10. Time-dependent flexural performance and design procedures for steel-bars truss slabs vol.73, pp.17, 2015, https://doi.org/10.1680/jmacr.19.00385
  11. Prediction of dry shrinkage deformation for partially enclosed steel reinforced concrete columns vol.44, pp.None, 2015, https://doi.org/10.1016/j.jobe.2021.102675
  12. Shrinkage-Induced Response of Composite Steel-Concrete Slabs: A State-of-the-Art Review vol.12, pp.1, 2015, https://doi.org/10.3390/app12010223