잉크젯 인쇄기술을 이용한 종이 스트레인게이지 개발

Development of a Paper Strain Gauge using Inkjet-printing Technology

  • 이영태 (안동대학교 전자공학교육과)
  • Lee, Young Tae (Department of Electronic Engineering Education, Andong National University)
  • 투고 : 2015.05.27
  • 심사 : 2015.06.22
  • 발행 : 2015.06.30

초록

In this paper, eco-friendly paper strain gauge was fabricated in the way of printing strain gauge on paper substrate, using PEDOT:PSS ink and inkjet printer technology. As a p-type conductive high polymer, PEDOT:PSS is known to be piezoresistive effect. I formed a strain gauge by connecting in parallel 5 lines of $60{\mu}m$ width printed with PEDOT:PSS. To minimize surrounding influence such as temperature, I formed wheat-stone bridge by combining 4 strain gauges (quarter-bridge strain gauge) which were made up of PEDOT:PSS 5 lines and measured. In quarter-bridge strain gauge, only two strain gauges, facing each other, arranged in strain and horizontal direction were deformed while the other two strain gauge of vertical direction were not. Therefore, quarter-bridge strain gauge showed the output of half bridge. The fabricated quarter-bridge strain gauge had output sensitivity of $105.6{\mu}V/V{\cdot}mm$ and its output linearity was relatively good.

키워드

참고문헌

  1. Udo Lang, Philipp Rust, Bernd Schoberle, Jurg Dual, "Piezoresistive properties of PEDOT:PSS," Microelectronic Enfineering, 86, pp. 330-334, (2009). https://doi.org/10.1016/j.mee.2008.10.024
  2. G. Latessa, F.Brunetti, A. Reale, G. Saggio, A. Di Carlo, "Piezoresistive behavior of dlexible PEDOT: PSS based sensor," Sensors and Actuators B, 139, pp. 304-309, (2009). https://doi.org/10.1016/j.snb.2009.03.063
  3. Udo Lang, Philipp Rust, Jurg Dual, "Toward fully polymeric MEMS: fabrication and testing of PEDOT: PSS strain gauge," Microelectronic Engineering, 85, pp. 1050-1053, (2008). https://doi.org/10.1016/j.mee.2008.01.051
  4. Nicolas Trifigny, Fern M. Kelly, Cedric Cochrane, Francois Boussu, Vladan Koncar, Damien Soulat, "PEDOT:PSS-based piezoresistive sensors applied to reinforcement glass fibres for in situ measurement during the composite material weaving process," Sensors, 13, pp. 10749-10764, (2013). https://doi.org/10.3390/s130810749
  5. Young Tae Lee, Seung Woo Cho, "Development of a strain gauge for sensing large strain," J. of the Semiconductor & Display Technology, 13(4), pp.33-36, (2014).
  6. Ji Won Kye, Dong Cheul Han, Han Jae Shin, Heon Gon Kim, Wang Hoon Lee, "Fabriaction of fluxible temperature &humidity sensor using inkjet-printing Technology," J. of Sensor Science and Technology, 24(2), pp. 119-123, (2015). https://doi.org/10.5369/JSST.2015.24.2.119
  7. Xinyu Liu, Martin Mwangi, XiuJun Li, Michael O'Brien, George M. Whitesides, "Paper-base piezoresistive MEMS sensors," Lab Chip, 11, pp.2189-2196, (2011). https://doi.org/10.1039/c1lc20161a
  8. Young Tae Lee, "Development of eco-friendly paper glucose bio-sensor," J. of Sensor Science and Technology, 22(3), pp. 202-206, (2013). https://doi.org/10.5369/JSST.2013.22.3.202