1. Introduction
Electric vehicles (EVs) are being actively research and development in recent years because they are an important way to deal with global environmental problems like global warming. EVs are characterized by motor drive systems, where electric power conversion is done by pulse width modulation (PWM) inverters [1-3].
The PWM technique provides high control efficiency and can be easily implemented based on the modern integrated circuit. Nevertheless the fast rise time of the switching transient produce high-frequency common mode (CM) electromagnetic interference (EMI) which leads to several serious problems such as CM current flowing to the ground through the stay capacitance of the system, shaft voltage and bearing current in motor, deterioration of motor winding insulation, radiation of power line, etc [4-6]. The problems of EMI may affect work state of motor drive systems and their surrounding electric device [7] and these highly concern the safety of EVs. Therefore,it is necessary to establish an accurate CM conducted EMI model for evaluating the level of the CM EMI in the motor drive system. Researchers have conducted a number of EMI modeling studies on the motor drive system of EVs [8-10] and other industrial applications [11-15]. A piecewise linear insulated gate bipolar transistor (IGBT) behavior model for frequency simulation of motor drive EMI prediction have been proposed [16]. The inverter model is composed of a control circuit and a three-phase IGBT module with parameters extracted from different device measurement. However, the control circuit and test procedure are complex. A physics-based high-frequency model of power inverter including the IGBT unit cells, heat sink and connective printed circuit board (PCB) traces combined in a single electrical circuit is presented [17]. The IGBT model includes the high-frequency stray component superimposed on the well-known Hefner IGBT model and the components is calculated using a 3-D quasistatic finite element analysis. The invert model by this method is relatively accurate. Nevertheless, the geometric dimensions and the structural physical parameters of the IGBT have to be known first. A high-frequency modeling method, which takes into account phenomena such as skin effects, proximity effects and dielectric losses, is used to model power cables by the series association of n identical RLCG basic cells [18]. The parameter values in the model are obtained by measurement and specific date processing. Other Studies have adopted a four-port impedance matrix representation of the power line considered in CM and the impedance parameters value have been practically measured in various conditions by considering the relationship between the voltage and current of the ports [19]. However, the obtained deviation of the model by the two mentioned methods is depended on the measurement accuracy. A lumped RLC circuit is used to model a motor in the frequency range under 1 MHz [20]. The parameters in the model include the winding-to-frame capacitance, winding-to-rotor capacitance and phase leakage inductance. The authors give a behavior model of AC motor [21]. The asymptotical and analytical methods are proposed to model the AC motor. Other alternative method [22] is proposed, including a finite element analysis [23]. However, with the frequency increasing above 1 MHz, all these methods are no longer suitable because of low accuracy.
This study aims to establish a prediction model of CM conducted interference for motor drive system of EVs. The high-frequency CM models of various parts of the system are proposed. First, the inverter model is presented. To model the inverter, a stray capacitor representing capacitive coupling between the IGBT and the heatsink and a CM voltage source, which takes into account the feature information of multiple interference sources, are used. This concentrated and equivalent method on the inverter can reduce the complexity of calculation simulation and it is easy to establish the model by experimental measurement. Second, a high-frequency CM model of the power line in EVs, using distributed parameter circuits calculated by combining the analytical method and finite element method (FEM), is detailed. This method can avoid the derivations error generated from measurements, however, the power line structures and parameters must be given at first. Third, a new approach based on vector fitting [24] is proposed to model a motor from 150 kHz to 30 MHz by using measured impedance date. Compared with the general modeling methods, this approach have a higher accuracy in a wide frequency range. At last, it will be shown that CM current and voltage can be predicted with a satisfactory accuracy using the proposed method.
2. Study System
The studied system (Fig. 1) is a motor drive system for EV applications. It is constituted of a direct current power supply, an industrial LISN, a three-phase IGBT inverter, a permanent magnet synchronous motor (PMSM), and a three-phase power line connecting the inverter to the motor. The complete system is placed on a copper plane to enable the EMI noise to circulate.
Fig. 1.DC/AC converter system with CM current pathways
Interference or noise flowing through heatsink, cable shielding layer, motor chassis and common ground is referred to as CM EMI. Note that in this study, only CM effects are considered, due to their dominant effects in EMI. Fig. 1 shows the CM current paths (ILISN and ICM) of the system with the noise source located in the main circuit. The CM currents exist because the sum of three instantaneous voltages at the output of the inverter is not null and capacitive couplings to ground are distributed in the complete system.
3. Modeling
The aim of the modeling is to predict conducted emissions in a variable-speed drive system. The essential question that needs to solve in CM modeling is obtaining the equivalent circuit parameters of each part in the CM conducted EMI propagation paths. Fig. 2 shows a simplified lumped element representation of the system. The CM equivalent circuits of the motor and power line need be precisely represented because these impedances have a significant influence on the level of conducted disturbances. The CM voltage source generated by the inverter should be carefully considered because the source is the reflex of the original EMI characteristics level in a system. In the following sections, we present several subsystem CM circuit models, such as the LISN model, inverter model, power line model, and motor model.
Fig. 2.Lump element equivalent circuit of the system
3.1 LISN Model
LISN is an industrial element for measuring the conducted interference in EMC standards. The parameters of the LISN circuit topology are provided by the manufacturers. In this study, LISN is located between a power supply and inverter for three functions: Firstly, to prevent incoming conducted disturbance from the power supply. Secondly, to maintain the stabilized impedance 50 ohms at the power electronics converter terminal in the wide frequency range, and finally to couple conducted interference voltage signal from the converter to the measuring receiver.
3.2 Inverter model
Fig. 3 shows the inverter stage with the main stray capacitor Ccm representing capacitive coupling between the IGBT and the heatsink, and the voltages Vag, Vbg and Vcg which are the output voltages of a leg of the inverter referenced to ground. In the common mode, the three inverter legs, generating the CM interference voltage, can be considered as a single voltage source Vcm. The model of Vcm and Ccm are presented in the following parts.
Fig. 3.CM equivalent model of the inverter
3.2.1 CM voltage source model
CM voltage generated by the inverter is expressed as
The system of impedances ZLISN constitutes a voltage divider, which makes the point P and N (Fig. 2) on the DC source have the voltage potential of 1/2E and -1/2E, respectively. As a space vector pulse width modulation (SVPWM) method is used in this system with the regulated DC source voltage E, the turn on signals of the higher transistors (K1, K3, K5) are shown as Fig. 4(a). Each voltage (Vag, Vbg and Vcg) has the value of 1/2E when the higher transistors are turned on, and -1/2E when the lower transistors (K2, K4, K6) are turned on. Then, substituting each voltage (E/2 or –E/2) into (1), the CM voltage Vcm is illustrated as Fig. 4(a). It can be observed that the voltage step of Vcm caused by the on/off of the switches are ±1/3E at every switching transient and this stairway voltage is particularly perturbing because it is constituted by six transients (dv/dt) per period.
Fig.4.CM voltage source modeling process
An electric vehicle industrial inverter supplied by the DC power source has been used in our experiments, its switching frequency was 7.5 kHz, and SVPWM strategy is used to generate the output voltages. The output voltages Vag, Vbg and Vcg are experimentally determined by using an Agilent oscilloscope and three Agilent high-voltage probes (Fig. 4(b)). Then, the CM voltage Vcm is obtained by the equation (1), as shown in Fig. 4(c).
The very essence of this modeling method for CM voltage source is that a stairway voltage is substituted for six switching elements by experimental measurements and subsequent calculations, and the characteristic of the CM EMI can be correctly described by the stairway voltage. Date from the CM voltage in Fig. 4(d) is stored in a memory module of simulation software where the date can be checked and edited. These data can be changed into a two-port model which represents the function of measured voltage through MAST language (Fig. 4(e)), then add the established model into component library. When building the CM conducted EMI circuit model of the variable-speed ac motor drive system in the simulation software, the established CM voltage source model should be invoked.
3.2.2 Parasitic parameter Ccm mode
The capacitive coupling to ground in the converter is mainly due to the power module and its heat sink, as explained by the schematic representation of Fig. 5(a). As the heat sink is connected directly to ground, this capacitance is a propagation path for the CM current.
The value of Ccm (Fig. 5(b)) is determined using an impedance analyzer. The impedances Zag, Zbg, and Zcg are measured between each leg of the inverter and the ground as shown in Fig. 5(c). The measured impedances are capacitive until 25 MHz, beyond 25 MHz, turning to inductive because of parasitic inductance introduced during measurement. In fact, this inductance does not exist in the system, so it can be neglected. Therefore, Zag, Zbg, and Zcg are assimilated to an identical capacitance Ccm equal to 267 pF from 150 kHz to 30 MHz. The impedance frequency characteristics comparison of Zag and Ccm is illustrated in Fig. 5(d).
Fig. 5.Parasitic parameter Ccm extraction process
3.3 Power line model
Power line spread paths of CM conducted disturbances in motor drive system. In order to predict the EMI level produced by the system, a high-frequency equivalent circuit model should be established for the power line.
Three cross-linked polyethylene insulated cables are used in the study, the geometrical and physical parameters of single phase cable are shown in Fig. 6(a), the conductor of cable is composed of 19 bundle mutual insulation copper wires, therefore, the variation of inductance and resistance with frequency by skin effect is neglected here; the shielding layer is connected to both the heatsink of the inverter and the shell of the PMSM, space between the cables is 50mm.
A power line can be viewed as a three conductor transmission line guided by transmission line theory, Fig. 6(b) shows per meter length model of the power line. Mutual capacitance CM of two conductors is considered to be zero in theory because of the shielding layer existing in each phase cable; and the value of mutual inductance LM, which is much less than self inductance because the space between the cable is large, can be neglected. All conductors are considered in parallel for the CM current propagation paths in the power line and the power line CM model can be described as Fig. 6(c).
In this section, we have proposed power line CM model (Fig. 6(c)) obtained by the series-association of N identical RLC basic cells. The analytic method is applied to calculate both the resistance parameters and the inductance parameters and FEM is employed to determine the capacitance parameters.
Fig. 6.Power line CM model process
3.3.1 Inductance parameters
The analytic method model to calculate self-inductance of single cable is shown in Fig. 7. The outer conductor and inner conductor represent the conductor and the shielding layer of the cable, respectively, the outer conductor has negligible thickness, and the current is uniformly distributed inside the inner conductor.
Fig. 7.Inductance parameters calculation model a=3.25 mm, b=4.55mm
The current density inside the inner conductor is
The magnetic flux density within the inner conductor at any radius ρ such that 0 ≤ ρ ≤ a , from Ampere’s law, is
The flux enclosed in the region between ρ and ρ+dρ , the unit length in the z direction is
As only a fraction of the total current is enclosed by the contour at radius ρ, the flux linkages are
Thus, the total flux linkages within the inner conductor are
Hence, the inductance per unit length of the inner conductor due to the flux inside it is
Next, determine the inductance due to the flux between the two conductors. The flux density in the region a ≤ ρ ≤ b is
The flux passing through the region between ρ and ρ + dρ , the unit length in the z direction is
The total flux linkages are
Thus, the contribution to the self-inductance by these flux linkages is
In the region b ≤ ρ , the magnetic flux density is zero. Hence, the total inductance per unit length of the insulated cable is
3.3.2 Capacitance parameters
For calculating the capacitance between the conductor and shielding layer, The FEM model of the phase cable is created in Maxwell 2D (Fig. 8). Calculating the capacitance from FEA is related to the electrostatic energy WC. The first step is to assign a voltage U1 to the conductor; the shielding layer in the volume V is grounded. FEA programme discretizes problem volume V into triquetrous element as shown in Fig. 8 and then solves the Laplace equation to get the electric field E1 and the displacement field D1 according to (13).
Fig. 8.FEM model for capacitance computation
Where, Фc is the electric scalar potential. The same procedure is applied to shielding layer in succession; in the end, WC 12 which is stored in the electric field associated with the capacitance between the conductor and shielding layer can be obtained from (14).
Since the energy can also be expressed
Where C represents the capacitance between conductor and shielding layer, further combing the (14) and (15), we can get C as
3.3.3 Resistance parameters
The resistance parameters of the per-unit-length conductor are defined as
The RLC parameters of the EMI model of the power line are computed using the aforementioned setup, and the equivalent circuit model of the per-unit-length power line (1m) is shown in Fig. 9.
Fig. 9.CM Equivalent circuit of the power line
3.4 Motor model
PMSM is a main propagation path for CM conducted emission of the drive system. In order to predict the EMI level, a high-frequency equivalent circuit model should be established for the motor. In this section, vector fitting (VF) method is proposed to model the PMSM with high accuracy from 150 kHz to 30 MHz, using measured impedance date.
3.4.1 Vector fitting technique
Vector fitting [24] is widely used for fitting a rational function for frequency domain response; it also is an accurate, robust, and efficient method. By applying vector fitting, the rational function of motor obtained by experimental date can be approximated a transfer function f(s) as
The terms rk and pk are the residues and poles, respectively, they could be real or complex conjugate pairs while d and e are real. In this paper, s is equivalent to j·ω for motor impedance application where ω is the angular frequency.
Then, we convert the rational approximation given by (18) into an equivalent circuit using in simulating software. It can be divided into several sub-circuits in terms of the order of the function as follows.
1) Equivalent circuit for d and e
A RL series circuit (Fig. 10(a)) will be used to synthesize the parameters d and e in function f(s). The values of R and L are
2) Equivalent circuit for real poles
The impedance rational expression for a real pole and residue is
A simple RC parallel circuit (Fig. 10(b)) is used to replace the rational function with one real pole. Comparing the circuit impedance with (20), the values of R and C are
3) Equivalent circuit for a complex conjugate pole pair
The complex conjugate pole pair can be expressed by the impedance rational as
Where pkc and are complex conjugate pole pair and rkc and are the residue pair. The equivalent circuit composed of RLC for representing (22) is shown in Fig. 10(c) and the values of these parameters are
Fig. 10.Equivalent circuit
With the sub-circuits obtained above, the total impedance of f(s) is represented by connecting sub-circuits in series.
3.4.2 CM impedance measurement and modeling
For the CM conducted emission of the system, the three phases of the motor are considered in parallel and the CM parameters of motor (ZCM) are identified by inspecting the input impedance measured between the motor three phase winding connected together and the motor frame, as shown in Fig. 11. The CM impedance is obtained by using an impedance analyzer in the frequency range from 150 kHz to 30 MHz.
Fig. 11.Schematic for testing ZCM
In consideration of a tradeoff between the accuracy and the complexity of the equivalent circuit by using VF models, 4-order approximation is used to model the CM impedance of the motor winding with a corresponding circuit topology shown in Fig. 12. The parameter values of the transfer function for 4-order approximation are given in Table 1 and the component values of the circuit are given in Table 2.
Fig. 12.4-order VF model
Table 1.Parameter values for 4-order transfer function
Table 2.Component values for 4-order CM equivalent
The simulated and experimental results of CM impedance are shown in Fig. 13. This curve shows that the ZCM impedance is almost capacitive when the frequency is below 6 MHz. when the frequency is increasing, the antiresonance occur at the frequency point 7 MHz as the phase angle at this point is 0° and the impedance behaviour is changing from capacitive to inductive. The comparisons of magnitude and phase date shows that the simulation results of 4-order equivalent circuit match the experimental results well in the entire bandwidth for both the magnitude and phase of the ZCM.
Fig. 13.Measurement and simulation results for motor CM model
4. Model Simulation and Experimental Verification
4.1 EMI simulation
The CM simulation model of the motor drive system is shown in Fig. 14(a). Where ZLISN represents the LISN module; the inverter module is consist of the CM excitation source and parasitic capacitance between the semiconductors and heat sink; the models of the power line and PMSM are characterized by ZPower line and ZMotor, respectively.
All the circuit modules are incorporated into the circuit simulation software and the detailed circuit simulation model of the motor drive system for CM EMI level is shown in Fig. 14(b). The transient emulation type has been selected and simulation computing time is 200 μs with simulation step size 0.1 ns. The CM conducted emission voltage VLISN and current ICM would be simulated and calculated to compare with the results measured on the experimental bench. Where VLISN can be expressed as:
Fig. 14.EMI CM model simulation of a motor drive system
4.2 EMI measurement
To validate the effectiveness of the EMI models proposed in this paper, we establish the experimental measurement platform of the motor drive system used in EVs. The setup of the experimental facilities is shown in Figs. 15(a) and (b).
Fig. 15.Experiment setup for the motor drive system
To simulate the actual mounting structures of the motor drive system in a car, the converter case is connected to the car body, which is replaced by the ground plane in the experimental platform. The ground plane comprises a galvanized steel plain sheet with a thickness of 1.2 mm, an area of 2400mm ´ 1000 mm, and a height of 1000 mm from the ground. Traction battery, as the DC power supply, is connected to the input terminal of LISN1 and output terminal of this device is connected to inverter. The PMSM (45kW) motor was fed by a three-phase voltage-source inverter through a 3-m shielded power line. The driving circuit of the inverter is power by a 12V battery through LISN2 connection to reduce the interference generated by the 12V battery; the start and end of inverter operation is controlled by the host computer through the CAN highway. Current have been measured using a FCC F-33-1 current probe (bandwidth=10 kHz-250 MHz) and the common mode EMI voltage VLISN is obtained as:
Where V1 and V2 are, respectively, the voltages measured at 1–traction battery 320 V, 2–LISN1, 3–inverter, 4–power line, 5– PMSM, 6–test stand, 7–ground plane, 8–LISN2, 9–12 V storage battery, 10–computer, 11–CAN highway the terminals of the LISN1.
The simulated and experimental common mode current in the power line shielding layer and motor chassis are presented in Fig. 16(a). Discrepancies between the simulation and experimental results are observed at some frequency ranges, such as 4 MHz to 5 MHz, with an error greater than 10 dB. However, the comparison of the simulation and measurement results indicates good conformance with errors less than 10 dB in the most of the frequency ranges. Therefore, the comparison results show the validity of the proposed power line model and motor model in CM conducted emission.
Fig. 16(b) shows the simulated and the measured results of CM conducted EMI at the terminal of the LISN ports. The comparison of the results in the range 750 kHz to 20 MHz indicates performance that corresponds to errors less than 5 dB, and the difference between the simulation and experimental results are observed at some frequency ranges, with an error no more than 10 dB. Therefore, the comparison results show the good behavior of the proposed inverter and LISN CM models.
Fig. 16.Comparison between measurement and calculation
These curves show that all impedances and CM source are accurately determined and our method is efficient in predicting CM conducted EMI for the motor drive system.
5. Conclusion
A pragmatic methodology is described in the paper to predict the CM conducted perturbation in a motor drive system of EVs. An equivalent circuit model has been proposed based on a representation of the full system. The model is reduced to the only described propagation, largely responsible for the major disturbances generated by these devices. Minimizing the complexity of the model make model easy to establish. The processing methods for the inverter consist of two steps: the CM voltage source is obtained by concentrating the output voltage waveform of each leg as one waveform; the stray capacitance has been identified by measurement. The CM model of the power lines based on transmission line model is used and the parameter extraction method in the model combines analytical method and FEM. The processing methods focuses on the motor CM parameters in the prediction model, establishes a high-frequency equivalent circuit model with high accuracy from 150 kHz to 30 MHz based on VF technique. The simulation and measurement results proved that the proposed model effectively describes the CM EMI levels of the motor drive system. The obtained model of the system would be used to design a CM filter for the reduction of conducted CM interference in EVs in future studies. While inserting a CM filter in a modeling such as presented herein, it is possible to design its component to obtain the desired attenuation with actual impedance. Lastly, this method is well matched to represent the CM current flowing in any part of the system: inverter, power line or motor chassis.
참고문헌
- A. Emadi, Y.J. Lee, and K. Rajashekara, “Power electronics and motor drives in electric, hybrid electric, and plug-in hybrid EVs,” IEEE Trans. on Industrial Electronic, vol. 55, no. 6, pp. 2237-2245, Jun. 2008 https://doi.org/10.1109/TIE.2008.922768
- M. Ehsani, Y.M. Gao, and J.M. Miller, “Hybrid EVs: architecture and motor drives,” Proceedings of the IEEE, vol. 95, no. 4, pp. 719-728, Apr. 2007 https://doi.org/10.1109/JPROC.2007.892492
- G. Nanda, and N.C. Kar, “A survey and comparison of characteristics of motor drives used in EVs,” Canadian Conference on Electrical and Computer Engineering, pp. 811-814, Ottawa, May 2006
- D.B. Jay Erdman, R.J. Kerkman, D. Schlegel, and G. Skibinski, “Bearing currents and their relationship to PWM drives,” IEEE Trans. on Power Electronics, vol. 12, no. 2, pp. 243-252, Mar. 1997 https://doi.org/10.1109/63.558735
- J.M. Erdman, R.J. Kerkman, D.W. Schlegel, and G.L. Skibinski, “ Effect of PWM inverters on AC motor bearing currents and shaft voltages,” IEEE Trans. on Industry Applications, vol. 32, no. 2, pp. 250-259, Apr. 1996 https://doi.org/10.1109/28.491472
- S.A. Pignari, and A. Orlandi, “Long-cable effects on conducted emissions levels,” IEEE Trans. on Electromagnetic Compatibility, vol. 45, no. 1, pp. 43-54, Feb. 2003 https://doi.org/10.1109/TEMC.2002.808023
- N. Moutoh, M. Nakanishi, M. Kanesaki, and J. Nakashima, “ EMI noise control methods suitable for electric vehicle drive systems,” IEEE Trans. on Electromagnetic Compatibility, vol. 47, no. 4, pp. 930-937, Nov. 2005 https://doi.org/10.1109/TEMC.2005.857893
- M.C. Di Piazza, A. Ragusa, and G. Vitale, “Common mode EMI propagation in high voltage DC supplied induction motor drives for EVs application, ” IEEE International Conference on Electric Machines and Drives, pp. 647-652, 2009
- C. Chen, and X. Xu, “ Modeling the conducted EMI emission of an electric vehicle (EV) traction drive,” IEEE International symposium on Electromagnetic Compatibility, vol.2, pp. 796-801, 1998
- Y.H. Lee, and A. Nasiri, “Analysis and modeling of conductive EMI noise of power electronics converters in electric and hybrid EVs,” Proceedings of 23th Annual IEEE Applied Power Electronics Conference and Exposition, pp. 1952-1957, 2008
- K. Jia, G. Bohlin, and R. Thottappillil, “Optimal cable assembly for reducing conducted electro-magnetic interference in the traction system,” IET Electrical Systems in Transportation, vol. 2, no. 1, pp. 29-37, 2012 https://doi.org/10.1049/iet-est.2011.0024
- L. Wang, C.N. Ho, and J. Jatskevich, “High-frequency modeling of the long-cable-fed induction motor drive system using TLM approach for predicting overvoltage transients,” IEEE Trans. on Power Electronics, vol. 25, no. 10, pp. 2653-2664, Oct. 2010 https://doi.org/10.1109/TPEL.2010.2047027
- M. Moreau, N. Idir, and P.L. Moigne, “Modeling of conducted EMI in adjustable speed drives,” IEEE Trans. on Electromagnetic Compatibility, vol. 51, no. 3, pp. 665-672, Aug. 2009 https://doi.org/10.1109/TEMC.2009.2025269
- V. Ardon, J. Aime, O. Chadebec, E. Clavel, J. Guichon, and E. Vialardi, “ EMC modeling of an industrial variable speed drive with an adapted PEEC method,” IEEE Trans. on Magnetics, vol. 46, no. 8, pp. 2892-2898, Aug. 2010 https://doi.org/10.1109/TMAG.2010.2043420
- D. Gallo, C. Landi, and N. Pasquino, “Experimental evaluation of conducted emissions by variable-speed drives under variable operating conditions,” IEEE Trans. on Instrumentation and Measurement, vol. 57, no. 7 pp. 1350-1356, Jul. 2008 https://doi.org/10.1109/TIM.2008.917176
- T. Qi, J. Graham, and J. Sun, “Characterization of IGBT modules for system EMI simulation”. Proceedings of 25th Annual IEEE Applied Power Electronics Conference and Exposition, pp. 2220-2225, 2010
- A. Nejadpak, and O.A. Mohammed, “Physics-based modeling of power converters from finite element electromagnetic field computations,” IEEE Trans. on Magnetics, vol.49, no.1, pp. 567-576, Jan. 2013 https://doi.org/10.1109/TMAG.2012.2206046
- N. Idir, Y. Weens, and J.J. Franchaud, “Skin effect and dielectric loss models of power cables, ” IEEE Trans. on Dielectrics and Electrical Insulation, vol. 16, no. 1, pp. 147-154, Feb. 2009 https://doi.org/10.1109/TDEI.2009.4784562
- F. Costa, C. Vollaire, and R. Meuret, “Modeling of conducted common mode perturbations in variable-speeddrive systems,” IEEE Trans. on Electromagnetic Compatibility, vol. 47, no. 4, pp. 1012-1021, Nov. 2005 https://doi.org/10.1109/TEMC.2005.857365
- A. Boglietti, A. Cavagnino, and M. Lazzari, “ Experimental high-frequency parameter identification of AC electrical motors,” IEEE Trans. on Industry Applications, vol.43, no.1, pp. 23-29, Feb. 2007 https://doi.org/10.1109/TIA.2006.887313
- N. Idir, Y. Weens, and J.J. Franchaud, “High-frequency behavior model of AC motors, ” IEEE Trans. on Magnetics, vol. 45, no. 1, pp. 133-138, Jan. 2009 https://doi.org/10.1109/TMAG.2008.2006006
- K. Gulez, and A. A. Adam, “ High-frequency CM modeling of permanent magnet synchronous motors,” IEEE Trans. on Electromagnetic Compatibility, vol. 50, no. 2, pp. 423-426, May. 2008 https://doi.org/10.1109/TEMC.2008.921032
- O.A. Mohammed, and S. Ganu, “FE-circuit coupled model of electric machines for simulation and evaluation of EMI issues in motor drives,” IEEE Trans. on Magnetics, vol. 46, no. 8, pp. 3389-3392, Aug. 2010 https://doi.org/10.1109/TMAG.2010.2045746
- B. Gustavsen, and A. Semlyen, “ Rational approximation of frequency domain responses by vector fitting,” IEEE Trans. on Power Delivery, vol. 14, No. 3, pp. 1052-1061, Jul. 1999 https://doi.org/10.1109/61.772353
피인용 문헌
- Prediction of Impedance Characteristics of MLCC Using Multiconductor Transmission Line Theory vol.58, pp.6, 2016, https://doi.org/10.1109/TEMC.2016.2588519