DOI QR코드

DOI QR Code

Buckling behavior of pultruded composite beams with circular cutouts

  • Aktas, Mehmet (Usak University, Department of Mechanical Engineering) ;
  • Balcioglu, H. Ersen (Usak University, Department of Mechanical Engineering)
  • Received : 2013.10.31
  • Accepted : 2014.03.10
  • Published : 2014.10.25

Abstract

In this experimental and numerical study, the effect of plate thickness, the diameter of circular cutout, the distance between circular cutouts and rowing orientation angle effect (${\theta}$) on the buckling load of E-glass/vinylester pultruded composite beams with single and double circular cutouts, were investigated. The composite beam having 2, 4, and 6 mm thicknesses was produced as [Mat/${\theta}$ /Mat/${\theta}$ /Mat] by using pultrusion technique. Seven different fiber angles as $0^{\circ}$, $15^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, $75^{\circ}$, and $90^{\circ}$ were chosen for investigation of rowing orientation angle. The distances between each circular cutout were selected as 15, 30, 45, 60, and 75 mm in the case of double circular cutouts. The diameters of circular cutouts were chosen as 2, 4, 6, 8, and 10 mm to investigate the effect of cutout size. The experimental buckling loads were compared with the results calculated from the numerical analysis. ANSYS 11 commercial software was used for numerical study. A good agreement was obtained between numerical and experimental results.

Keywords

References

  1. Akbulut, H. and Ural, T. (2007), "An investigation on buckling of composite laminated plates with corner circular notches", J. Thermoplast. Compos. Mater., 20(4), 371-387. https://doi.org/10.1177/0892705707079608
  2. Aktas, M. (2009), "Buckling behaviour of carbon/epoxy laminated composite plates under biaxial loading", Adv. Compos. Lett., 18(3), 85-93.
  3. Anil, V., Upadhyay, C.S. and Iyengar, N.G.R. (2007), "Stability analysis of composite laminate with and without rectangular cutout under biaxial loading", Compos. Struct., 80(1), 92-104. https://doi.org/10.1016/j.compstruct.2006.04.088
  4. Arman, Y., Zor, M. and Aksoy, S. (2006), "Determination of critical delamination diameter of laminated composite plates under buckling loads", Compos. Sci. Tech., 66(15), 2945-2953. https://doi.org/10.1016/j.compscitech.2006.02.014
  5. ASTM (1990), "Standard test method for tensile properties of fiber-resin composite D 3039-76", American Society for Testing and Materials, PA, USA.
  6. Baba, B.O. (2007), "Buckling behavior of laminated composite plates", J. Reinf. Plast. Compos., 26, 1637-1655. https://doi.org/10.1177/0731684407079515
  7. Balcioglu, H.E. and Aktas, M. (2012), "Lateral buckling behavior of laminated composite materials with delamination", Proceedings of the 14th International Materials Symposium, Denizli, Turkey, October.
  8. Balcioglu, H.E. and Aktas, M. (2013), "An investigation on lateral buckling of laminated composites with delamination", Ind. J. Eng. Mater. Sci., 20(5), 367-375.
  9. Baltaci, A., Sarikanat, M. and Yildiz, H. (2006), "Buckling analysis of laminated composite circular plates with holes", J. Reinf. Plast. Compos., 25(7), 733-744. https://doi.org/10.1177/0731684406062065
  10. Haj-Ali, R. and Kilic, H. (2002), "Nonlinear behavior of pultruded FRP composites", Compos.: Part B, 33(3), 173-191. https://doi.org/10.1016/S1359-8368(02)00011-2
  11. Haj-Ali, R. and Kilic, H. (2003), "Nonlinear constitutive models for pultruded FRP composites", Mech. Mater., 35(8), 791-801. https://doi.org/10.1016/S0167-6636(02)00207-7
  12. Mottram, J.T. (2004), "Determination of critical load for flange buckling in concentrically loaded pultruded columns", Compos.: Part B, 35(1), 35-47. https://doi.org/10.1016/j.compositesb.2003.08.006
  13. Papadopoulos, L. and Kassapoglou, C. (2004), "Shear buckling of rectangular composite plates with two concentric layups", J. Reinf. Plast. Compos., 23(1), 5-16. https://doi.org/10.1177/0731684404028698
  14. Ranganathan, S. and Mantena, P.R. (2003), "Axial loading and buckling response characteristics of pultruded hybrid glass-graphite/epoxy composite beams", J. Reinf. Plast. Compos., 22(7), 671-679. https://doi.org/10.1177/073168403024566
  15. Roberts, T.M. and Masri, H.M.K.J.A.H. (2003), "Section properties and buckling behavior of pultruded FRP profiles", J. Reinf. Plast. Compos., 22(14), 1305-1317. https://doi.org/10.1177/0731684403035584
  16. Saha, M., Prabhakaran, R. and Waters, W.A. (2004), "Compressive behavior of pultruded composite plates with circular holes", Compos. Struct., 65(1), 29-36. https://doi.org/10.1016/j.compstruct.2003.10.002
  17. Tercan, M. and Aktas, M. (2009), "Buckling behavior of 1 ${\time}$ 1 rib knitting laminated plates with cutouts", Compos. Struct., 89(2), 245-252. https://doi.org/10.1016/j.compstruct.2008.07.030
  18. Wang, Y. (2002), "Bearing behavior of joints in pultruded composites", J. Compos. Mater., 36(18), 2199-2216. https://doi.org/10.1177/0021998302036018535
  19. Yapici, A., Sahin, O.S. and Arikan, H. (2005), "Buckling of metal-reinforced thermoplastic composite laminated plates with holes", J. Reinf. Plast. Compos., 24(13), 1379-1386. https://doi.org/10.1177/0731684405049885
  20. Yazici, M. (2008), "Buckling of square perforated thermoplastic composite plates", J. Reinf. Plast. Compos., 27(10), 1059-1070. https://doi.org/10.1177/0731684407087055
  21. Yazici, M. (2009), "Influence of cut-out variables on buckling behavior of composite plates", J. Reinf. Plast. Compos., 28(19), 2325-2339. https://doi.org/10.1177/0731684408092058
  22. Yazici, M., Ozcan, R., Ulku, S. and Okur, I. (2003), "Buckling of composite plates with U-shaped cutouts", J. Compos. Mater., 37(24), 2179-2195. https://doi.org/10.1177/002199803038109
  23. Yeh, H.Y., Le, R.M. and Yeh, H.L. (2007), "Buckling of metal-matrix composite plate with a square hole", J. Reinf. Plast. Compos., 26(5), 525-540. https://doi.org/10.1177/0731684407075529

Cited by

  1. Failure load prediction of adhesively bonded pultruded composites using artificial neural network vol.50, pp.23, 2016, https://doi.org/10.1177/0021998315617998
  2. Collapse of steel cantilever roof of tribune induced by snow loads vol.23, pp.3, 2014, https://doi.org/10.12989/scs.2017.23.3.273
  3. Position optimization of circular/elliptical cutout within an orthotropic rectangular plate for maximum buckling load vol.29, pp.1, 2014, https://doi.org/10.12989/scs.2018.29.1.039
  4. Buckling behavior of composite cylindrical shells with cutout considering geometric imperfection vol.30, pp.4, 2019, https://doi.org/10.12989/scs.2019.30.4.305
  5. Review on Local Buckling of Hollow Box FRP Profiles in Civil Structural Applications vol.13, pp.23, 2014, https://doi.org/10.3390/polym13234159