Advances in aircraft and spacecraft science

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Valve actuation effects on discrete monopropellant slug delivery in a micro-scale fuel injection system

  • McDevitt, M. Ryan (Mechanical Engineering Program, School of Engineering, University of Vermont) ;
  • Hitt, Darren L. (Mechanical Engineering Program, School of Engineering, University of Vermont)
  • Received : 2014.02.13
  • Accepted : 2014.05.16
  • Published : 2014.10.25
⟨ Previous Next ⟩

Abstract

Converging flows of a gas and a liquid at a microchannel cross junction, under proper conditions, can result in the formation of periodic, dispersed microslugs. This microslug formation phenomenon has been proposed as the basis for a fuel injection system in a novel, 'discrete' monopropellant microthruster designed for use in next-generation miniaturized satellites. Previous experimental studies demonstrated the ability to generate fuel slugs with characteristics commensurate with the intended application during steady-state operation. In this work, numerical and experimental techniques are used to study the effect of valve actuation on slug characteristics, and the results are used to compare with equivalent steady-state slugs. Computational simulations of a valve with a 1 ms valve-actuation cycle show that as the ratio of the response time of the valve to the fully open time is increased, transient effects can increase slug length by up to 17%. The simulations also demonstrate that the effect of the valve is largely independent of surface tension coefficient, which is the thermophysical parameter most responsible for slug formation characteristics. Flow visualization experiments performed using a miniature valve with a 20 ms response time showed less than a 1% change in the length of slugs formed during the actuation cycle. The results of this study indicate that impulse bit and thrust calculations can discount transient effects for slower valves, but as valve technology improves transient effects may become more significant.

Keywords

References

  1. Bouwmeester, J. and Guo, J. (2010), "Survey of worldwide pico- and nanosatellite missions, distributions and subsystem technology", Acta Astronautica, 67, 854-862. https://doi.org/10.1016/j.actaastro.2010.06.004
  2. Cubaud, T. and Ho, C. (2004), "Transport of bubbles in square microchannels", Phys. Fluid., 16(12), 4575-4585. https://doi.org/10.1063/1.1813871
  3. Cubaud, T., Tatineni, M., Zhong, X. and Ho, C. (2005), "Bubble dispenser in microfluidic devices", Phys. Rev. E, 72(3), 037302. https://doi.org/10.1103/PhysRevE.72.037302
  4. Garstecki, P., Fuerstmann, M., Stone, H. and Whitesides, G., (2006), "Formation of droplets and bubbles in a microfluidic T-junction-scaling and mechanism of breakup", Lab. Chip., 6, 437-446. https://doi.org/10.1039/b510841a
  5. Hitt, D., Zakrzwski, C. and Thomas, M. (2001), "MEMS-based satellite micropropulsion via catalyzed hydrogen peroxide decomposition", J. Smart Mater. Struct., 10, 1163-1175 https://doi.org/10.1088/0964-1726/10/6/305
  6. Janson, S. (2008), The history of small satellites, Eds. Helvajian, H. and Janson, S., Small Satellites, Past, Present and Future.
  7. Kujawa, J. and Hitt, D. (2004), "Transient shutoff simulations of a realistic MEMS supersonic nozzle", Proceedings of the 40th AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit, Ft. Lauderdale, July.
  8. Lewis, D., Janson, S. and Cohen, R. (2000), "Digital micro-propulsion project", Sens. Actuat. A, 80, 143-154. https://doi.org/10.1016/S0924-4247(99)00260-5
  9. Louisos, W. and Hitt, D. (2011), "Analysis of transient flow in supersonic micronozzles", J. Spacecraft Rock., 48(2), 303-311. https://doi.org/10.2514/1.51027
  10. McCabe, J., Hitt, D. and McDevitt, M. (2012), "A micro-scale monopropellant fuel injection scheme using two-phase slug formation", J. Propuls. Pow., 27(6) 1295-1302
  11. McDevitt, M. and Hitt, D., (2011), "Numerical study of disperse monopropellant slug formation at a cross junction", Proceedings of the 41st AIAA Fluid Dynamics Conference, Honolulu, June.
  12. Osher, S. and Sethian, J. (1988), "Fronts propagating with curvature-dependent speed: algorithms based on Hamilton-Jacobi formulations", J. Comput. Phys., 79, 1249.
  13. Olsson, E. and Kreiss, G., (2005), "A conservative level set method for two phase flow", J. Comput. Phys., 210, 225-246. https://doi.org/10.1016/j.jcp.2005.04.007
  14. Qian, D. and Lawal, A. (2006), "Numerical study of gas and liquid slugs for Taylor flow in T-junction microchannel", Chem. Eng. Sci., 61, 7609-7625. https://doi.org/10.1016/j.ces.2006.08.073
  15. Thorsen, T., Roberts, R., Arnold, F. and Quake, S. (2001), "Dynamic pattern formation in a vesicle generating microfluidic device", Phys. Rev. Lett., 86, 4163-4166. https://doi.org/10.1103/PhysRevLett.86.4163