DOI QR코드

DOI QR Code

Minimum dynamic response of cantilever beams supported by optimal elastic springs

  • Aydin, Ersin (Faculty of Engineering, Department of Civil Engineering, Nigde University)
  • Received : 2012.04.17
  • Accepted : 2014.04.04
  • Published : 2014.08.10

Abstract

In this study, optimal distribution of springs which supports a cantilever beam is investigated to minimize two objective functions defined. The optimal size and location of the springs are ascertained to minimize the tip deflection of the cantilever beam. Afterwards, the optimization problem of springs is set up to minimize the tip absolute acceleration of the beam. The Fourier Transform is applied on the equation of motion and the response of the structure is defined in terms of transfer functions. By using any structural mode, the proposed method is applied to find optimal stiffness and location of springs which supports a cantilever beam. The stiffness coefficients of springs are chosen as the design variables. There is an active constraint on the sum of the stiffness coefficients and there are passive constraints on the upper and lower bounds of the stiffness coefficients. Optimality criteria are derived by using the Lagrange Multipliers. Gradient information required for solution of the optimization problem is analytically derived. Optimal designs obtained are compared with the uniform design in terms of frequency responses and time response. Numerical results show that the proposed method is considerably effective to determine optimal stiffness coefficients and locations of the springs.

Keywords

References

  1. Akesson, B. and Olhof, N. (1988), "Minimum stiffness of optimally located supports for maximum value of beam eigenfrequencies", J. Sound. Vib., 120(3), 457-463. https://doi.org/10.1016/S0022-460X(88)80218-9
  2. Albaracin, J.M., Zannier, L. and Gross, R.O. (2004), "Some observations in the dynamics of beams with intermediate supports", J. Sound. Vib., 271, 475-480. https://doi.org/10.1016/S0022-460X(03)00631-X
  3. Aydin, E. and Boduroglu, M.H. (2008), "Optimal placement of steel diagonal braces for upgrading the seismic capacity of existing structures and its comparison with optimal dampers", J. Construct. Steel Res., 64, 72-86. https://doi.org/10.1016/j.jcsr.2007.04.005
  4. Aydin, E., Boduroglu, M.H. and Guney, D. (2007), "Optimal damper distribution for seismic rehabilitation of planar building structures", Engineering Structures, 29, 176-185. https://doi.org/10.1016/j.engstruct.2006.04.016
  5. Bojczuk, D. and Mroz, Z. (1998), "On optimal design of supports in beam and frame structures", Struct. Optim., 16, 47-57. https://doi.org/10.1007/BF01213999
  6. Bojczuk, D. and Mroz, Z. (1998), "Optimal design of trusses with account for topology variation", Mech. Struct. Mach., 26(1), 21-40. https://doi.org/10.1080/08905459808945418
  7. Buhl, T. (2001), "Simultaneous topology optimization of structure and supports", Struct. Multidiscip. Optim., 23, 336-346.
  8. Ching, H.C. and Gene, J.W.H. (1992), "Eigenvalue sensitivity analysis of planar frames with variable joint and support locations", AIAA J., 30(8) 2138-3147. https://doi.org/10.2514/3.11192
  9. Cimellaro, G.P. (2007), "Simultaneous stiffness-damping optimization of structures with respect to acceleration, displacement and base shear", Eng. Struct., 29, 2853-2870. https://doi.org/10.1016/j.engstruct.2007.01.001
  10. Dems, K. and Turant, J. (1997), "Sensitivity analysis and optimal design of elastic hinges and supports in beam and frame structures", Mech. Struct. Mach., 25(4), 417-443. https://doi.org/10.1080/08905459708905297
  11. Fayyah, M.M. and Razak, H.A. (2012), "Condition assessment of elastic bearing supports using vibration data", Construct. Build. Mater., 30, 616-628. https://doi.org/10.1016/j.conbuildmat.2011.12.043
  12. Frishwell, M.I. and Wang, D. (2007), "The minimum support stiffness required to raise the fundamental natural frequency of plate structures", J. Sound. Vib., 301, 665-677. https://doi.org/10.1016/j.jsv.2006.10.016
  13. Garstecki, A. and Mroz, Z. (1987), "Optimal design of supports of elastic structures subject to loads and initial distortions", Mech. Struct. Mach., 15, 47-68. https://doi.org/10.1080/08905458708905108
  14. Imam, M.H. and Al-Shihri, M. (1996), "Optimum topology of structural supports", Comput. Struct., 61(1), 147-154. https://doi.org/10.1016/0045-7949(96)00087-9
  15. Jihang, Z. and Weighong, Z. (2006), "Maximization of structural natural frequency with optimal support layout", Struct. Multidisc. Optim., 31, 462-469. https://doi.org/10.1007/s00158-005-0593-2
  16. Kong, J. (2009), "Vibration of isotropic and composite plates using computed shape function and its application to elastic support optimization", J. Sound. Vib., 326, 671-686. https://doi.org/10.1016/j.jsv.2009.05.022
  17. Lin, H.Y. (2010), "An exact solution for free vibrations of a non-uniform beam carrying multiple elastic supported rigid bars", Struct. Eng. Mech., 34(4), 399-416. https://doi.org/10.12989/sem.2010.34.4.399
  18. Liu, Z.S., Hu, H.C. and Wang, D.J. (1996), "New method for deriving eigenvalue rate with respect to support locations", AIAA J., 34, 864-866. https://doi.org/10.2514/3.13158
  19. Marcelin, J.L. (2001), "Genetic search applied to selecting support position in machining of mechanical parts", Int. J. Adv. Manufact. Technol., 17, 344-347. https://doi.org/10.1007/s001700170169
  20. Mroz, Z. and Lekszycki, T. (1982), "Optimal support reaction in elastic frame structures", Comput. Struct., 14, 179-185.
  21. Mroz, Z. and Haftka, R.T. (1994), "Design sensitivity of non-linear structures in regular and critical states", Int. J. Solid. Struct., 31, 2071-2098. https://doi.org/10.1016/0020-7683(94)90191-0
  22. Mroz, Z. and Rozvany, G.I.N. (1975), "Optimal design of structures with variable support positions", J. Opt. Theory Appl., 15, 85-101. https://doi.org/10.1007/BF00933023
  23. Olhof, N. and Akessson, B. (1991), "Minimum stiffness of optimally located supports for maximum value of column buckling loads", Struct. Multidiscip. Optim., 3, 163-175. https://doi.org/10.1007/BF01743073
  24. Olhof, N. and Taylor, J.E. (1998), "Designing continuous columns for minimum total cost of material and interior supports", J. Struct. Mech., 6(4), 367-382.
  25. Prager, W. and Rozvany, G.I.N. (1975), "Plastic design of beams; optimal locations of supports and steps in yield moment", Int. J. Mech. Sci, 17, 627-631. https://doi.org/10.1016/0020-7403(75)90080-6
  26. Przemieniecki, J.S. (1968), Theory of Matrix Structural Analysis, McGraw-Hill, Newyork.
  27. Rozvany, G.I.N. (1975), "Analytical treatment of some extended problems in structural optimization", J. Struct. Mech., 1, 359-385.
  28. Sinha, J.K. and Frishwell, M.I. (2001), "The location of spring supports from measured vibration data", J. Sound. Vib., 244(1), 137-153. https://doi.org/10.1006/jsvi.2000.3461
  29. Son, J.H. and Kwak, B.M. (1993), "Optimization of boundary conditions for maximum fundamental frequency of vibrating structures", AIAA J., 31(12), 2351-2357. https://doi.org/10.2514/3.11935
  30. Szelag, D. and Mroz, Z. (1978), "Optimal design of elastic beams with unspecified support positions", ZAMM, 58, 501-510. https://doi.org/10.1002/zamm.19780581105
  31. Takewaki, I. (1998), "Optimal damper positioning in beams for minimum dynamic compliance", Comput. Method. Appl. Mech. Eng., 156, 363-373. https://doi.org/10.1016/S0045-7825(97)00221-1
  32. Wang, B.P. (1993), "Eigenvalue sensitivity with respect to location of internal stiffness and mass attachment", AIAA J., 31, 791-794. https://doi.org/10.2514/3.11621
  33. Wang, B.P. and Chen, J.L. (1996), "Application of genetic algorithm for the support location optimization of beams", Comput. Struct., 58(4), 597-800. https://doi.org/10.1016/0045-7949(95)00151-6
  34. Wang, C.Y. (2003), "Minimum stiffness of an internal elastic support to maximize the fundamental frequency of a vibrating beam", J. Sound. Vib., 259(1), 229-232. https://doi.org/10.1006/jsvi.2002.5100
  35. Wang, D. (2004), "Optimization of support positions to minimize the maximal deflection of structures", Int. J. Solid. Struct., 41, 7445-7458. https://doi.org/10.1016/j.ijsolstr.2004.05.035
  36. Wang, D. (2006), "Optimal design of structural support positions for minimizing maximal bending moment", Finite Elem. Anal. Des., 43, 95-102. https://doi.org/10.1016/j.finel.2006.07.004
  37. Wang, D., Frishwell, M.I. and Lei, Y. (2006), "Maximizing the natural frequency of a beam with an intermediate elastic support", J. Sound. Vib., 291, 1229-1238. https://doi.org/10.1016/j.jsv.2005.06.028
  38. Wang, D., Jiang, J.S. and Zhang, W.H. (2004), "Optimization of support positions to maximize the fundamental frequency of structures", Int. J. Numer. Method. Eng., 61, 1584-1602. https://doi.org/10.1002/nme.1124
  39. Wang, D., Yang, Z.C. and Yu Z.G. (2010), "Minimum stiffness location of point support for control of fundamental natural frequency of rectangular plate by Rayleigh-Ritz method", J. Sound. Vib., 329, 2792-2808. https://doi.org/10.1016/j.jsv.2010.01.034
  40. Won, K.M. and Park, Y.S. (1998), "Optimal support positions for a structure to maximize its fundamental natural frequency", J. Sound. Vib., 213(5), 801-812. https://doi.org/10.1006/jsvi.1997.1493
  41. Zhu, J.H. and Zhang, W.H., (2010), "Integrated layout design of supports and structures", Comput. Method. Appl. Mech. Eng., 199, 557-569. https://doi.org/10.1016/j.cma.2009.10.011

Cited by

  1. Optimization of elastic spring supports for cantilever beams vol.62, pp.1, 2014, https://doi.org/10.1007/s00158-019-02469-3
  2. Exact closed-form solution for free vibration of Euler-Bernoulli and Timoshenko beams with intermediate elastic supports vol.213, pp.None, 2014, https://doi.org/10.1016/j.ijmecsci.2021.106842