DOI QR코드

DOI QR Code

Compression tests of cold-formed channel sections with perforations in the web

  • Kwon, Young Bong (Department of Civil Engineering, Yeungnam University) ;
  • Kim, Gap Deuk (Department of Steel Research, RIST) ;
  • Kwon, In Kyu (Department of Fire Protection Engineering, Kangwon National University)
  • 투고 : 2013.03.01
  • 심사 : 2014.02.18
  • 발행 : 2014.06.25

초록

This paper describes a series of compression tests performed on cold-formed steel channel sections with perforations in the web (thermal studs) fabricated from a galvanized steel plate whose thickness ranged from 1.0 mm to 1.6 mm and nominal yield stress was 295 MPa. The structural behavior and performance of thermal studs undergoing local, distortional, or flexural-torsional buckling were investigated experimentally and analytically. The compression tests indicate that the slits in the web had significant negative effects on the buckling and ultimate strength of thin-walled channel section columns. The compressive strength of perforated thermal studs was estimated using equivalent solid channel sections of reduced thickness instead of the studs. The direct strength method, a newly developed and adopted alternative to the effective width method for designing cold-formed steel sections in the AISI Standard S100 (2004) and AS/NZS 4600 (Standard Australia 2005), was calibrated to the test results for its application to cold-formed channel sections with slits in the web. The results verify that the DSM can predict the ultimate strength of channel section columns with slits in the web by substituting equivalent solid sections of reduced thickness for them.

키워드

과제정보

연구 과제 주관 기관 : Yeungnam University

참고문헌

  1. American Iron and Steel Institute (AISI) (2004), Standard, Supplement 2004 to the North American Specifications for Design of Cold-Formed Steel Structural Members, Washington D.C., USA.
  2. American Iron and Steel Institute Standard (AISI) (2012), North American Specifications for the Design of Cold-Formed Steel Structural Members, Washington D.C., USA.
  3. Cheng, B. and Li, C. (2012), "Buckling behavior of strengthened perforated plates under shear loading", Steel Compos. Struct., Int. J., 13(4), 367-382. https://doi.org/10.12989/scs.2012.13.4.367
  4. Davis, J.M., Leach, P. and Taylor, A. (1997), "The design of perforated cold-formed steel sections Subjected to axial load and bending", Thin-Wall. Struct., 29(1-4), 41-57.
  5. European Committee for Standardization (ECS) (2001), Eurocode 3: Design of Steel Structures, Part 1-3: General rules- Supplementary rules for cold-formed thin gauge members and sheeting, Brussels, Belgium.
  6. European Committee for Standardization (ECS) (2003), Eurocode 3: Design of Steel Structures, Part 1-1: General rules and rules for buildings, Brussels, Belgium.
  7. FEA Co., Ltd. (2012), Lusas Element Reference Manual & User's Manual (version 14.7).
  8. Hancock, G.J., Murray, T.M. and Ellifritt, D.S. (2004), Cold-Formed Steel Structures to the AISI Specification, Marcel Dekker, Inc., NY, USA.
  9. Hoglund, T. and Burstand, H. (1998), "Slotted steel studs to reduce thermal bridges in insulated walls", Thin-Wall. Struct., 32(1-3), 81-109. https://doi.org/10.1016/S0263-8231(98)00028-7
  10. Kesti, J. (2000), "Local and distortional buckling of perforated steel wall studs", Ph.D. Thesis, Helsingki University of Technology, Finland.
  11. Korean Standard Association (2006), KSD3506, Hot-Dip Zinc Coated Steel Sheets and Coils, Seoul, Korea. [In Korean]
  12. Kwon, Y.B. (2000), Buckling Analysis Program (BAP) User's Manual (Ver 2.0), Department of Civil Engineering, Yeungnam University, Korea.
  13. Kwon, Y.B., Kim B.S. and Hancock G.J. (2009), "Compression tests of high strength cold-formed steel channels with buckling interaction", J. Construct. Steel Res., 65(2), 278-289. https://doi.org/10.1016/j.jcsr.2008.07.005
  14. Kwon, Y.B. and Hancock, G.J. (1992), "Post-buckling behaviour of thin-walled sections undergoing local and distortional buckling", Comput. Struct., 49(3), 507-516.
  15. Moen, C.D. and Schafer, B.W. (2009), "Elastic buckling of thin plates with holes in compression or bending", Thin-Wall. Struct., 47(12), 1597-1607. https://doi.org/10.1016/j.tws.2009.05.001
  16. Salmi, P. (1998), Design of web-perforated steel wall studs, Fourth Finnish steel structures R&D days, Lappeenrante, Finland.
  17. Salhab, B. and Wang, Y.C. (2008), "Effective thickness of cold-formed thin-walled channel sections with perforated webs under compression", Thin-Wall. Struct., 46(7), 823-838.
  18. Schafer, B.W. (2008), "The direct strength method of cold-formed steel member design", J. Construct. Steel Res., 64(7), 766-778. https://doi.org/10.1016/j.jcsr.2008.01.022
  19. Schafer, B.W. and Pekoz, T. (1998), Direct Strength Prediction of Cold-Formed Steel Members using Numerical Elastic Buckling Solutions, Thin-Walled Structures, Research and Development, (Eds. Shanmugan, N.E., Liew, J.Y.R. and Thevendran, V.), Elsevier, pp. 137-144.
  20. Standard Australia (2005), Cold-Formed Steel Structures AS/NZS 4600, Sydney, Australia.
  21. Venkataramaiah, K.R. and Roorda, J. (1982), "Analysis of local plate buckling experimental data", Proceedings of the 6th International Specialty Conference on Cold-Formed Steel Structure, University of Missouri-Rolla,, St. Louis, MO, USA, October.
  22. Walker, A.C. (1975), Design and Analysis of Cold-Formed Sections, International Textbook Company Ltd., London, UK.
  23. Wang, Y.C. and Salhab, B. (2009), "Structural behavior and design of light weight structural panels using perforated cold-formed thin-walled sections under compression", Int. J. Steel Struct., 9(1), 57-67. https://doi.org/10.1007/BF03249480

피인용 문헌

  1. Nonlinear finite element modeling of steel-sheathed cold-formed steel shear walls vol.22, pp.1, 2016, https://doi.org/10.12989/scs.2016.22.1.079
  2. Distortional buckling of cold-formed lipped channel columns subjected to axial compression vol.23, pp.3, 2017, https://doi.org/10.12989/scs.2017.23.3.331
  3. Strength and stiffness of cold-formed steel portal frame joints using quasi-static finite element analysis vol.25, pp.6, 2014, https://doi.org/10.12989/scs.2017.25.6.727
  4. Rotational capacity of H-shaped steel beams under cyclic pure bending vol.30, pp.2, 2014, https://doi.org/10.12989/scs.2019.30.2.123
  5. Stability analysis of cold-formed channels using mathematical programming techniques vol.16, pp.6, 2014, https://doi.org/10.1108/mmms-11-2019-0207
  6. Boosting machines for predicting shear strength of CFS channels with staggered web perforations vol.34, pp.None, 2014, https://doi.org/10.1016/j.istruc.2021.09.060
  7. Cold-formed ferritic stainless steel perforated tubular stub columns: Behaviour and design vol.170, pp.None, 2014, https://doi.org/10.1016/j.tws.2021.108654