DOI QR코드

DOI QR Code

Applicability of over-coring technique to loaded RC columns

  • Campione, Giuseppe (Dipartimento di Ingegneria Civile Ambientale Aerospaziale e dei Materiali DICAM, Universita di Palermo) ;
  • Minafo, Giovanni (University "Kore" of Enna, Faculty of Engineering and Architecture, Cittadella Universitaria)
  • 투고 : 2012.06.13
  • 심사 : 2014.05.17
  • 발행 : 2014.07.10

초록

Stress determination is a very important step in the assessment of the safety of existing reinforced concrete structures. In rock mechanic this goal is achieved with the over-coring technique. The main idea behind such a technique is to isolate a material sample from the stress field in the surrounding mass and monitor its re-equilibrium deformation response. If the materials remains elastic, and elastic properties are known, stresses may be obtained from the corresponding measured strains. The goal of this paper is to evaluate if the over-coring technique is applicable to reinforced concrete members. The results of an experimental investigation on the behaviour of compressed concrete columns subjected to the over-coring technique are presented. Considerations about the range of applicability of the technique are made by comparing the measured and the theoretical stresses. After that, results of failure tests on drilled specimens are presented and discussed. Furthermore, the response is compared with that of columns core-bored before the compressive test. Finally, comparisons with numerical analysis are shown.

키워드

참고문헌

  1. ACI 228.1R-03 (2003), "In-place methods for determination of strength of concrete", ACI Mater. J., 85(5), 446-471.
  2. ACI 214.4R (2008), "Guide for obtaining cores and interpreting compressive strength results", Detroit, Michigan.
  3. British Standards Institution (1981), "BS 6089: Guide to Assessment of Concrete Strength in Existing Structures", London W4 4AL, United Kingdom.
  4. RILEM Draft Recommendation 43-CND (1993), "Combined non-destructive testing of concrete - Draft recommendation for in situ concrete strength determination by combined non destructive methods", Mater. Struct., 26, 43-49. https://doi.org/10.1007/BF02472237
  5. Leite, M.H., Boivin, V. and Corthesy, R. (2010), "Stress calculation methods for overcoring techniques in heterogeneous rocks", Int. J. Rock Mech. Min. Sci., 47(7), 1180-1192. https://doi.org/10.1016/j.ijrmms.2010.06.002
  6. ASTM E837 - 08e1 (2008), "Standard Test Method for Determining Residual Stresses by the Hole-Drilling Strain-Gage Method", ASTM International, West Conshohocken, PA, DOI: 10.1520/E0837-08E01.
  7. Barrallo, J., Zulueta, A. and Sanchez-Beitia, S. (1999), "The donostia method for the stress measurements in architectural heritage", Strain, 35(3), 107-112. https://doi.org/10.1111/j.1475-1305.1999.tb01141.x
  8. Sanchez-Beitia, S. (2007), "Stress analysis in the Altes Museum (Berlin) by means of the Hole Drilling Technique (Donostia Method)", Construct. Build. Mater., 21(8), 1680-1688. https://doi.org/10.1016/j.conbuildmat.2006.05.052
  9. Sanchez Beitia, S. (2008), "Stress analysis of the piers of the Tarazona Cathedral (Zaragoza-Spain) by means of the hole-drilling technique", Construct. Build. Mater., 22(5), 966-971. https://doi.org/10.1016/j.conbuildmat.2006.11.024
  10. Sanchez-Beitia, S. and Shueremans, L. (2009), "The Hole Drilling technique for on site deduction of the stresses states in stone masonry by using eight strain gages", Construct. Build. Mater., 23, 2041-2046. https://doi.org/10.1016/j.conbuildmat.2008.08.032
  11. McGinnis, M.J., Pessiki, S. and Turker, H. (2005), "Application of 3D digital image correlation to the coredrilling method", Exper. Mech., 45(4), 359-367. https://doi.org/10.1007/BF02428166
  12. Trautner, C., McGinnis, M.J. and Pessiki, S. (2011), "Application of the incremental core-drilling method to determine in-situ stresses in concrete", ACI Mater. J., 108(3), 290-299.
  13. Coetzer, S. (1997), "Conceptual development of a method to determine the principal stress around coal mine workings to ensure safe mine design", Final Project Report, Safety in Mines Research Advisor Committee (SIMRAC).
  14. Zhu, L., Xu, Q., Li, X. and Zhu, C. (2010), "Experimental studies of reinforced concrete column capacity affected by core drilling", Adv. Mater. Res., 133-134, 1195-1200. https://doi.org/10.4028/www.scientific.net/AMR.133-134.1195
  15. Campione, G. and Minafo, G. (2011), "Experimental investigation on compressive behavior of bottle-shaped struts", ACI Struct. J., 108(3), 294-303.
  16. ASTM C 1196 (2009), "Standard test method for in situ compressive stress within solid unit masonry estimated using flatjack measurements", ASTM International, West Conshohocken, PA, DOI: 10.1520/C1196-09.
  17. Cervenka, V. (2000), "Simulating a response", Concrete Eng. Int., 4(4), 45-49.
  18. ACI Committee 318 (2008), "Building code requirements for structural concrete (ACI 318-08)", and Commentary (ACI 318R-08), American Concrete Institute, Detroit, Michigan.
  19. Eurocode 2, "Design of concrete structures - Part 1-1: General - Common rules for building and civil engineering structures".