DOI QR코드

DOI QR Code

Prediction of post fire load deflection response of RC flexural members using simplistic numerical approach

  • Lakhani, Hitesh (Reactor Safety Division, Bhabha Atomic Research Centre) ;
  • Singh, Tarvinder (Reactor Safety Division, Bhabha Atomic Research Centre) ;
  • Sharma, Akanshu (Institute of Construction Materials, University of Stuttgart) ;
  • Reddy, G.R. (Reactor Safety Division, Bhabha Atomic Research Centre) ;
  • Singh, R.K. (Reactor Safety Division, Bhabha Atomic Research Centre)
  • 투고 : 2013.04.01
  • 심사 : 2014.04.04
  • 발행 : 2014.06.25

초록

A simplistic approach towards evaluation of complete load deflection response of Reinforced Concrete (RC) flexural members under post fire (residual) scenario is presented in this paper. The cross-section of the RC flexural member is divided into a number of sectors. Thermal analysis is performed to determine the temperature distribution across the section, for given fire duration. Temperature-dependent stress-strain curves for concrete and steel are then utilized to perform a moment-curvature analysis. The moment-curvature relationships are obtained for beams exposed to different fire durations. These are then utilized to obtain the load-deflection plots following pushover analysis. Moreover one of the important issues of modeling the initial stiffness giving due consideration to stiffness degradation due to material degradation and thermal cracking has also been addressed in a rational manner. The approach is straightforward and can be easily programmed in spreadsheets. The presented approach has been validated against the experiments, available in literature, on RC beam subjected to different fire durations viz. 1hr, 1.5hrs and 2hrs. Complete load-deflection curves have been obtained and compared with experimentally reported counterparts. The results also show a good match with the results obtained using more complicated approaches such as those involving Finite element (FE) modeling and conducting a transient thermal stress analysis. Further evaluation of the beams during fire (at elevated temperatures) was performed and a comparison of the mechanical behavior of RC beams under post fire and during fire scenarios is made. Detailed formulations, assumptions and step by step approach are reported in the paper. Due to the simplicity and ease of implementation, this approach can be used for evaluation of global performance of fire affected structures.

키워드

참고문헌

  1. ACI 318M-11 (2011), Building Code Requirements for Reinforced Concrete, American Concrete Institute, Detroit, Michigan.
  2. Anderberg, Y. and Thelandersson, S. (1976), "Stress and deformation characteristics of concrete at high temperature, experimental investigation and material and material behavior model", Bulletin 54Lund Institute of Technology, Lund, Sweden
  3. Annerel, E. and Taerwe, L. (2009), "Approaches for the assessment of the residual strength of concrete exposed to fire", Concrete Repair, Rehabilitation and Retrofitting II, 615-621
  4. Applied Technology Council (2005), "Improvement of nonlinear static seismic analysis procedures", Report No FEMA-440, Washington DC
  5. Belkacem, T., Hocine, C., Hacene, H. and Resheidat, M. (2008), "Effects of cooling condition on residuals properties of high-performance concrete at high temperature", International Conference on Construction and Building Technology, 135-142
  6. Chen, B., Li, C.L. and Chen, L.Z. (2009), "Experimental study of mechanical properties of normal strength concrete exposed to high temperatures at early age", Fire Saf. J., 44, 997-1002 https://doi.org/10.1016/j.firesaf.2009.06.007
  7. CEB-FIP Bulletin 46 (2008), Fire design of concrete structures-structural behaviour and assessment, Federation Internationale du beton (fib).
  8. Chang, Y.F., Chen, Y.H., Sheu, M.S. and Yao, G.C. (2006), "Residual stress- strain relationship for concrete after exposure to high temperatures", Cement Concrete Res., 36, 1999-2005 https://doi.org/10.1016/j.cemconres.2006.05.029
  9. El-Hawary, M.M., Ragab, A.M., El-Azim, A.A. and Elibiarif, S. (1996), "Effect of fire on flexural behaviour of RC beams", Construct. Build. Mater., 10(2), 147-150 https://doi.org/10.1016/0950-0618(95)00041-0
  10. Eurocode 2 (2004), Design of concrete structures. Part 1.2: General rules- structural fire design (EN1992-1-2:2004), Commission of European Communities, Brussels
  11. Freskakis, G.N. (1984), "Behaviour of reinforced concrete at elevated temperatures", Proceedings ASCE Conference on Structural Engineering in Nuclea Facilities, Raleigh, North Caroline
  12. Freskakis, G.N., Burrow, R.C. and Debbas, E.B. (1979), "Strength properties of concrete at elevated temperatures", ASCE National Convention, Boston, Massachusetts
  13. Ghandehari, M., Behnood, A. and Khanzadi, M. (2010), "Residual mechanical properties of high strength concrete after exposure to elevated temperatures", J. Mater. Civil Eng., 22(1), 59-64 https://doi.org/10.1061/(ASCE)0899-1561(2010)22:1(59)
  14. Harmathy, T.Z. and Berndt, J.E. (1966), "Hydrated Portland cement and light weight concrete at elevated temperatures", J. Am. Concrete Ins., 63(1), 93-112
  15. Hertz, K.D. (2005), "Concrete strength for fire safety design", Mag. Concrete Res., 57(8), 445-453 https://doi.org/10.1680/macr.2005.57.8.445
  16. Hsu, J.H. and Lin, C.S. (2006), "Residual bearing capabilities of fire-exposed reinforced concrete beams", Int. J. Appl. Acien. Eng., 4(2), 151-163
  17. IS: 1786 (1985), Specification for high strength deformed steel bars and wires for concrete reinforcement, Bureau of Indian Standards, New Delhi
  18. ISO 834-1 (1999), Fire resistance tests-elements of building construction
  19. Jayasree, G., Lakshmipathy, M. and Santhanaselvi, S. (2011), "Behaviour of RC beams under elevated temperature", J. Struct. Fire Eng., 2(1), 45-55 https://doi.org/10.1260/2040-2317.2.1.45
  20. Kent, D.C. and Park, R. (1971), "Flexural members with confined concrete", J. Eng., 97(ST7), 1969-1990
  21. Knaack, A.M., Kurama, Y.C. and Kirkner, D.J. (2010), "Compressive strength relationships for concrete under elevated temperatures", ACI Mater. J, 107(2), 164-175
  22. Kodur, V.K.R., Dwaikat, M.B. and Fike, R.S. (2010), "An approach for evaluating the residual strength of fire exposed RC beams", Mag. Concrete Res., 62(7), 479-488 https://doi.org/10.1680/macr.2010.62.7.479
  23. Kodur ,V.K.R., Dwaikat, M.M.S. and Dwaikat, M.B. (2008), "High-temperature properties of concrete for fire resistance modelling of structures", ACI Materi. J., 105(5), 517-527
  24. Kumar, A. and Kumar, V. (2003), "Behaviour of RCC beams after exposure to elevated temperatures", J. Ins. Eng., Civil Eng. Div., 84(4), 165-170
  25. Lee, J.S., Xi, Y.P. and William, K. (2008), "Properties of concrete after high temperature heating and cooling", ACI Mater. J., 105(4), 334-341
  26. Lienhard, J.H., Lienhard, J. (2008), A Heat Transfer Textbook, 3rd Edition, Cambridge, Massachusetts, Phlogiston Press
  27. Malhotra, H.L. (1982), "Properties of materials at high temperatures", Report on the Technical Committee 44-PHT, 161-170
  28. Neves, I.C., Rodrigues, J.C. and Loureiro, A.P. (1996), "Mechanical properties of reinforcing and prestressing steels after heating", J. Mater. Civil Eng., 8(4), 189-194 https://doi.org/10.1061/(ASCE)0899-1561(1996)8:4(189)
  29. Ozbolt, J. Bosnjak, J., Periskic, G. and Sharma, A. (2013), "3D numerical analysis of reinforced concrete beams exposed to elevated temperatures", Eng. Struct., 58, 166-174.
  30. Park, R. and Paulay, T. (1975), Reinforced Concrete Structures, John Wiley & Sons, New York
  31. Poon, C.S., Azhar, S., Anson, M. and Wong, Y.L. (2001), "Comparison of the strength and durability performance of normal- and high-strength pozzolanic concretes at elevated temperatures", Cement Concrete Res., 31, 1291-1300 https://doi.org/10.1016/S0008-8846(01)00580-4
  32. Schneider, U. (1988), "Concrete at high temperatures- a general review", Fire Saf. J., 13, 55-68 https://doi.org/10.1016/0379-7112(88)90033-1
  33. Sharma, A., Reddy, G.R., Elighausen, R. and Vaze, K.K. (2011), "Experimental and analytical investigation on seismic behaviour of RC framed structure", Struct. Eng. Mech., 39(1), 125-145 https://doi.org/10.12989/sem.2011.39.1.125
  34. Takeuchi, M., Hiranoto, M., Kumagai, N., Yamazaki, N., Kodaira, A. and Sugiyama, K. (1993), "Material properties of concrete and steel rebars at elevated temperatures", Proceedings of the 12th International Conference on Structural Mechanics in Reactor Technology, Paper No. H04/4m, Elsevier Science Publication, 133-138
  35. Terro, M.J. and Hamoush, S.A. (1997), "Effect of confinement on siliceous aggregate concrete subjected to elevated temperatures and cyclic heating", ACI Mater. J., 94(2), 83-89
  36. Youssef, M.A. and Moftah, M. (2007), "General stress strain relationship for concrete at elevated temperatures", Eng. Struct., 29, 2618-2634 https://doi.org/10.1016/j.engstruct.2007.01.002

피인용 문헌

  1. A coupled thermo-mechanical inelastic analysis approach for reinforced concrete flexural members during fire 2017, https://doi.org/10.1002/suco.201700071
  2. Behavior of prestressed concrete box bridge girders Under hydrocarbon fire condition vol.210, 2017, https://doi.org/10.1016/j.proeng.2017.11.100
  3. Evaluating fire resistance of prestressed concrete bridge girders vol.62, pp.6, 2014, https://doi.org/10.12989/sem.2017.62.6.663
  4. Postfire Damage Assessment of a RC Factory Building vol.33, pp.5, 2019, https://doi.org/10.1061/(asce)cf.1943-5509.0001319
  5. Impact Analysis of Thermally Pre-Damaged Reinforced Concrete Frames vol.13, pp.23, 2020, https://doi.org/10.3390/ma13235349
  6. Estimating Postfire Residual Capacity of Heavily Damaged Concrete Members vol.35, pp.2, 2014, https://doi.org/10.1061/(asce)cf.1943-5509.0001561