DOI QR코드

DOI QR Code

Experimental study on creep and shrinkage of high-performance ultra lightweight cement composite of 60MPa

  • Chia, Kok-Seng (Nautic Group Pte Ltd.) ;
  • Liu, Xuemei (School of Civil Engineering and Built Environment, Queensland University of Technology) ;
  • Liew, Jat-Yuen Richard (Department of Civil and Environmental Engineering, National University of Singapore) ;
  • Zhang, Min-Hong (Department of Civil and Environmental Engineering, National University of Singapore)
  • 투고 : 2013.11.09
  • 심사 : 2014.03.19
  • 발행 : 2014.06.10

초록

Creep and shrinkage behaviour of an ultra lightweight cement composite (ULCC) up to 450 days was evaluated in comparison with those of a normal weight aggregate concrete (NWAC) and a lightweight aggregate concrete (LWAC) with similar 28-day compressive strength. The ULCC is characterized by low density < 1500 $kg/m^3$ and high compressive strength about 60 MPa. Autogenous shrinkage increased rapidly in the ULCC at early-age and almost 95% occurred prior to the start of creep test at 28 days. Hence, majority of shrinkage of the ULCC during creep test was drying shrinkage. Total shrinkage of the ULCC during the 450-day creep test was the lowest compared to the NWAC and LWAC. However, corresponding total creep in the ULCC was the highest with high proportion attributed to basic creep (${\geq}$ ~90%) and limited drying creep. The high creep of the ULCC is likely due to its low elastic modulus. Specific creep of the ULCC was similar to that of the NWAC, but more than 80% higher than the LWAC. Creep coefficient of the ULCC was about 47% lower than that of the NWAC but about 18% higher than that of the LWAC. Among five creep models evaluated which tend to over-estimate the creep coefficient of the ULCC, EC2 model gives acceptable prediction within +25% deviations. The EC2 model may be used as a first approximate for the creep of ULCC in the designs of steel-concrete composites or sandwich structures in the absence of other relevant creep data.

키워드

참고문헌

  1. ACI 209 (1992), Prediction of creep, shrinkage, and temperature effects in concrete structures, ACI 209R-92, American Concrete Institute, Farmington Hills.
  2. ACI 209 (2005), Report on Factors Affecting Shrinkage and Creep of Hardened Concrete, American Concrete Institute ACI 209.1R-05.
  3. ACI 209 (2008), Guide for Modeling and Calculating Shrinkage and Creep in Hardened Concrete, ACI 209.2R-08, American Concrete Institute, Farmington Hills.
  4. ASTM C426-10 (2010), Standard test method for linear drying shrinkage of concrete masonry units, ASTM international, West Conshohocken (PA).
  5. ASTM C512/C512M-10 (2010), Standard test method for creep of concrete in compression, ASTM international, West Conshohocken (PA).
  6. Bentz, D.P. and Weiss, W.J. (2011), "Internal Curing: A 2010 State-of-the-Art Review," National Institute of Standards and Technology, NISTIR 7765.
  7. Branson, D.E. and Christiason, M.L. (1971), "Time Dependent Concrete Properties Related to Design - Strength and Elastic Properties, Creep and Shrinkage," Creep, Shrinkage and Temperature Effects, SP-27, American Concrete Institute, Farmington Hills, MI, 257-277.
  8. BSI (2004), BS EN 1992-1-1: 2004, Eurocode 2: Design of concrete structures- Part 1-1: General rules and rules for buildings, British Standards Institute, London.
  9. CEB (1993), CEB-FIP Model Code 1990, CEB Bulletin d'Information No.213/214, Comite Euro-International du Beton, Lausanne, Switzerland.
  10. CEB (1999), Structural concrete - textbook on behaviour, design and performance. Updated knowledge of the CEB/FIP Model Code 1990, fib Bulletin 2, V.2, Federation Internationale du Beton, Lausanne, Switzerland, 37-52.
  11. CEB/FIP (1983), FIP Manual of Lightweight Aggregate Concrete (2nd Edition), Surrey University Press, Glasgow and London.
  12. Chia, K.S., Zhang, M.H. and Liew, J.Y.R. (2011), "High-strength ultra lightweight cement composite - material properties", Proceedings of the 9th international symposium on high performance concrete-design, verification & ulitility, Rotorua, New Zealand, August.
  13. Gardner, N.J. and Lockman, M.J. (2001), "Design provisions for drying shrinkage and creep of normal strength concrete", ACI Mat. J., 98(2), 159-167.
  14. Gardner, N.J. (2004), "Comparison of prediction provisions for drying shrinkage and creep of normal strength concretes", Can. J. Civil Eng., 31(5), 767-775. https://doi.org/10.1139/l04-046
  15. Kwak, H.G., Ha, S.J. and Kim, J.K. (2006a), "Non-structural cracking in RC walls, Part I. Finitite element formulation," Cement Concrete Res., 36, 749-760. https://doi.org/10.1016/j.cemconres.2005.12.001
  16. Kwak, H.G. and Ha, S.J. (2006b), "Non-structural cracking in RC walls, Part II. Quantitative prediction model," Cement Concrete Res., 36, 761-775. https://doi.org/10.1016/j.cemconres.2005.12.002
  17. Lopez, M., Kahn, L.F. and Kurtis, K.E. (2004), "Creep and shrinkage of high-performance lightweight concrete", ACI Mat. J., 101(5), 391-399.
  18. Sohel, K.M.A., Liew, J.Y.R., Yan, J.B., Zhang, M.H. and Chia, K.S. (2012), "Behavior of steel-concrete-steel sandwich structures with lightweight cement composite and novel shear connectors", Compos. Struct., 94, 3500-3509. https://doi.org/10.1016/j.compstruct.2012.05.023

피인용 문헌

  1. Development of ultra-lightweight cement composites with low thermal conductivity and high specific strength for energy efficient buildings vol.87, 2015, https://doi.org/10.1016/j.conbuildmat.2015.04.004
  2. Properties investigation of fiber reinforced cement-based composites incorporating cenosphere fillers vol.140, 2017, https://doi.org/10.1016/j.conbuildmat.2017.02.093
  3. Mechanical properties and microstructure of ultra-lightweight cement composites with fly ash cenospheres after exposure to high temperatures vol.164, 2018, https://doi.org/10.1016/j.conbuildmat.2018.01.009
  4. Utilization of fly ash cenosphere as lightweight filler in cement-based composites – A review vol.144, 2017, https://doi.org/10.1016/j.conbuildmat.2017.03.188
  5. Numerical modeling of the aging effects of RC shear walls strengthened by CFRP plates: A comparison of results from different "code type" models vol.19, pp.5, 2014, https://doi.org/10.12989/cac.2017.19.5.579
  6. Experimental investigation of creep and shrinkage of reinforced concrete with influence of reinforcement ratio vol.7, pp.4, 2014, https://doi.org/10.12989/acc.2019.7.4.211
  7. Three-Dimensional Printability of White Portland Cement Containing Cenospheres vol.118, pp.6, 2014, https://doi.org/10.14359/51733119
  8. Shear bond behavior of composite slabs with ultra-lightweight cementitious composite vol.44, pp.None, 2014, https://doi.org/10.1016/j.jobe.2021.103284