Structural Engineering and Mechanics

  • 제50권4호
  • /
  • Pages.563-573
  • /
  • 2014
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

An approach to improve thickness distribution and corner filling of copper tubes during hydro-forming processes

  • GhorbaniMenghari, Hossein (Department of Mechanical Engineering, Isfahan University of Technology) ;
  • Poor, Hamed Ziaei (Department of Mechanical Engineering, Isfahan University of Technology) ;
  • Farzin, Mahmoud (Department of Mechanical Engineering, Isfahan University of Technology) ;
  • Alves De Sousa, Ricardo J. (Department of Mechanical Engineering, University of Aveiro)
  • 투고 : 2013.12.10
  • 심사 : 2014.03.27
  • 발행 : 2014.05.25
⟨ 이전 논문 다음 논문 ⟩

초록

In hydroforming, the general technique employed to overcome the problem of die corner filling consist in increasing the maximum fluid pressure during the forming process. This technique, in other hand, leads to other difficulties such as thinning and rupturing of the final work piece. In this paper, a new technique has been suggested in order to produce a part with complete filled corners. In this approach, two moveable bushes have been used. So, the workpiece moves driven by both bushes simultaneously. In the first stage, system pressure increases until a maximum of 15 MPa, providing aninitial tube bulge. The results showed that the pressure in this stage have to be limited to 17 MPa to avoid fracture. In a second stage, bushes are moved keeping the constant initial pressure. The punches act simultaneously at the die extremities. Results show that the friction between part and die decreases during the forming process significantly. Also, by using this technique it is possible to produce a part with reasonable uniform thickness distribution. Other outcomes of applying this method are the lower pressures required to manufacture a workpiece with complete filled corners with no wrinkling.

키워드

참고문헌

  1. Al-Qureshi, H. and Moriera Filhp, L. (2001), "Junction forming in aluminum tubes using an elastomer", Tech., Mat. Manuf. Proc., 16, 717-724. https://doi.org/10.1081/AMP-100108631
  2. Altan, T. and Tekkaya, A.E. (2012), Sheet Metal Forming Processes and Applications, ASM International, Ohio, USA.
  3. Aue-U-Lan, Y., Ngaile, G. and Altan, T. (2004), "Optimizing tube hydroforming using process simulation and experimental verification", J. Mater. Proc. Tech., 146, 137-143. https://doi.org/10.1016/S0924-0136(03)00854-9
  4. Hwang, Y. and Altan, T. (2002), "Finite element analysis of tube hydroforming processes in a rectangular die", Finite Elem. Anal. Des., 39, 1071-1082.
  5. Hwang, Y.M. and Chen, W.C. (2005), "Analysis of tube hydroforming in a square cross-section die", Int. J. Plastic., 21, 1815-33. https://doi.org/10.1016/j.ijplas.2004.09.004
  6. Imaninejad, M., Subhash, G. and Loukus, A. (2005), "Load path optimization of tube hydroforming process. international", J. Mach. Tool. Manuf., 45, 1504-1514. https://doi.org/10.1016/j.ijmachtools.2005.01.029
  7. Kridli, G.T., Bao, L., Mallick, P.K. and Tian, Y. (2003), "Investigation of thickness variation and corner filling in tube hydroforming", J. Mater. Proc. Tech., 133, 287-96. https://doi.org/10.1016/S0924-0136(02)01004-X
  8. Lei, L.P., Kang, B.S. and Kang, S.J. (2001), "Prediction of the forming limit in hydroforming process using the finite element method and a ductile fracture criterion", J. Mater. Proc. Tech., 113, 673-679. https://doi.org/10.1016/S0924-0136(01)00694-X
  9. Maki, T. (2003), "Current status of fluid forming in automotive industry, hydroforming of tubes, extrusions and sheet metals", IFU, Ed. K. Siegert, 3, 25-44.
  10. Maki, T. (2013), "Forming of automotive aluminum body panels by sheet hydroforming", Key Eng. Mater., 554-557, 1273-1281. https://doi.org/10.4028/www.scientific.net/KEM.554-557.1273
  11. Viorel, P., Nicoraa, D. and Ciocan, O. (2003), Design of an Experimental Device for Tube Hydroforming Technology, The Annals "DUNAREA DE JOS" University of Galati Fascicle V, Technologies in Machine Building.
  12. Woo, D.M. (1973), "Tube-bulging under internal pressure and axial force", J. Eng. Mater. Tech., 95, 219-223. https://doi.org/10.1115/1.3443156
  13. Xu, X., Li, S., Zhang, W. and Lin, Z. (2009), "Analysis of thickness distribution of square-sectional hydroformed parts", J. Mater. Proc. Tech., 209, 158-64. https://doi.org/10.1016/j.jmatprotec.2008.01.034
  14. Ziaei Poor, H. and Moosavi, H. (2013), "An investigation of wrinkling and thinning in hydroforming deep drawing process with hemispherical punch", Int. J. Mech. Syst. Eng., 3, 89-96.
  15. Ziaei Poor, H. and Moosavi, H. (2013), "Prevent of wrinkling and rupturing using a new method based on punch force in hydro-mechanical deep drawing process", Int. J. Mech. Syst. Eng., 3, 125-128.

피인용 문헌

  1. Investigation into bulging-pressing compound forming for sheet metal parts with very small radii 2018, https://doi.org/10.1007/s00170-017-1207-z
  2. Analytical model of corner filling with granular media to investigate the friction effect between tube and media vol.99, pp.1-4, 2018, https://doi.org/10.1007/s00170-018-2429-4