DOI QR코드

DOI QR Code

Cryogenic Machining of Open-Cell Silicone Foam

액화질소를 이용한 오픈 셀 실리콘 폼의 냉동 절삭조건 최적화

  • Hwang, Jihong (Department of Mechanical System Design Engineering, Seoul National University of Science and Technology) ;
  • Cho, Kwang-Hee (Department of Mechanical System Design Engineering, Seoul National University of Science and Technology) ;
  • Park, Min-Soo (Department of Mechanical System Design Engineering, Seoul National University of Science and Technology)
  • Received : 2013.10.04
  • Accepted : 2014.01.21
  • Published : 2014.02.15

Abstract

Open-cell silicon foam is difficult to cut using conventional machining processes because of its low stiffness. That is, open-cell silicon foam is easily pressed down when the tool is engaged, which makes it difficult to remove the material in the form of chip. This study proposes an advanced method of machining open-cell silicon foam by freezing the material using liquid nitrogen. Furthermore, the machining conditions are optimized to maximize the efficiency of material removal and minimize the usage of liquid nitrogen by conducting experiments under various machining conditions. The results show that open-cell silicone foam products with free surface can be successfully machined by employing the proposed method.

Keywords

References

  1. Briquet, F., Colas, A., Thomas, X., 1996, Silicones for Medical Use, Dow Corning Customer Service Center, UK.
  2. Furman, E. L, Finkelstein, A. B.., Cherny, M. L., 2013, Permeability of Aluminum Foams Produced by Replication Casting Metals 3 49-57.
  3. Kaynak, Y., Karaca, H. E., Noebe, R. D., Jawahir, L. S., 2013, Tool-wear Analysis in Cryogenic Machining of NiTi Shape Memory Alloys: A Comparison of Tool-wear Performance with Dry and MQL Machining, Wear 306 51-63. https://doi.org/10.1016/j.wear.2013.05.011
  4. Hong, S., Ding, Y., 2001, Cooling Approaches and Cutting Temperatures in Cryogenic Machining of Ti-6Al-4V, Int. J. Mach. Tool. Manu. 41 1417-1437. https://doi.org/10.1016/S0890-6955(01)00026-8
  5. Yildiz, Y., Nalbant, M., 2008, A Review of Cryogenic Cooling in Machining Processes, Int. J. Mach. Tool. Manu. 48 947-964. https://doi.org/10.1016/j.ijmachtools.2008.01.008
  6. Navas, V. G., Arriola, A., Gonzalo, O., Leunda, J., 2013, Mechanisms Involved in the Improvement of Inconel 718 Machinability by Laser Assisted Machining (LAM), Int. J. Mach. Tool. Manu. 74 19-28. https://doi.org/10.1016/j.ijmachtools.2013.06.009
  7. Skvarenina, S., Shin, Y. C., 2006, Laser-assisted Machining of Compacted Graphite Iron, Int. J. Mach. Tool. Manu. 46 7-17. https://doi.org/10.1016/j.ijmachtools.2005.04.013
  8. Lei, S., Shin, Y. C., Incropera, F. P., 2000, Deformation Mechanisms and Constitutive Modeling for Silicon Nitride Undergoing Laser-assisted Machining, Int. J. Mach. Tool. Manu. 40 2213-2233. https://doi.org/10.1016/S0890-6955(00)00051-1