다구찌법에 의한 STD11의 와이어방전가공에서 표면거칠기에 관한 연구

A Study on Surface Roughness in Wire Electrical Discharge Machining of STD11 based on Taguchi method

  • 최만성 (한국기술교육대학교 메카트로닉스공학부)
  • Choi, Man Sung (School of Mechatronics Engineering, Korea University of Technology and Education)
  • 투고 : 2014.08.01
  • 심사 : 2014.08.29
  • 발행 : 2014.09.30

초록

The experimental analysis presented aims at the selection of the most optimal machining parameter combination for wire electrical discharge machining (WEDM) of STD11. Based on the Taguchi experimental design ($L_{27}$ orthogonal array) method, a series of experiments were performed by considering time-on, voltage, time-off, wire speed, and flow rate as input parameters. The surface roughness was considered responses. Based on the signal-to-noise (S/N) ratio, the influence of the input parameters on the responses was determined. The optimal machining parameters setting for the minimum surface roughness was found using Taguchi methodology. In order to investigate the effects of process parameters on the surface machined by WEDM, Several experiments are conducted to consider effects of time-on, voltage, time-off, wire speed and flow rate on the surface roughness. Analysis of variance (ANOVA) as well as regression analysis are performed on experimental data. The best results of surface roughness were obtained at higher voltage, lower wire speed, and lower time-on.

키워드

참고문헌

  1. Koenig, W., Dauw .D.F., Levy. G., Panten .U., "EDM-future steps towards the machining of ceramics", Ann. CIRP Vol. 37, No. 2, pp. 625-631, 1998.
  2. Dauw, D.F., Charmilles, "technologies: facing the future, in: Paper Presented During the Inauguration of CT-Japan", Yokohama, Japan, 14 April 1989.
  3. Stovicek, D.R., "The State-of-the-art EDM Science: Tooling and Production", Vol. 59, No. 2, Nelson Publishing Inc., Ohio, USA, May, p. 42, 1993.
  4. Dauw, D.F et al., "Surface topography investigations by fractal analysis of spark eroded electrically conductive ceramics", Ann. CIRP Vol. 39, No. 1, pp.161-165, 1990. https://doi.org/10.1016/S0007-8506(07)61026-9
  5. Ho, K H., Newman, S. T., Rahimifard, S., Allen, R D., "State of the art in wire electrical discharge machining (WEDM)", International Journal of Machine Tools & Manufacture, Vol. 44, pp 1247-1259. 2004 https://doi.org/10.1016/j.ijmachtools.2004.04.017
  6. Hewidy, M. S., El-Taweel, El- Safty . T. A, M. F., "Modelling the machining parameters of WEDM of Inconel 601 using RSM", Journal of Materials Processing Technology, Vol. 336., pp 169-328, 2005.
  7. Dvsss, V. Prasad, A. Gopalakrishna., "Empirical modeling and optimization of wire electrical discharge machining", Int J Adv. Manuf. Technol., Vol. 43, pp 914-925, 2009. https://doi.org/10.1007/s00170-008-1769-x
  8. Lee, S.H., "Optimization of cutting parameters for burr minimization in face-milling operations", Int. J. Prod. Res. Vol. 41, No. 3, pp. 497-511, 2003. https://doi.org/10.1080/0020754021000042382
  9. Yang . W.H., Tarng . Y.S., "Design optimization of cutting parameters for turning operations based on the Taguchi method, J. Mater. Process". Technol. Vol. 84, pp. 122-129, 1998. https://doi.org/10.1016/S0924-0136(98)00079-X
  10. Lin .T.R., "Optimization technique for face milling stainless steel with multiple performance characteristics", Int. J. Adv. Manuf. Technol. Vol. No. 19, pp. 330-335, 2002. https://doi.org/10.1007/s001700200021
  11. Davim .J.P., Antonio . C.A.C., "Optimization of cutting conditions in machining of aluminium metal matrix composites using a numerical and experimental model", J. Mater. Process. Technol. Vol. 112, pp. 78-82, 2002.
  12. Tosun, N., "The effect of the cutting parameters on performance of WEDM", KSME Int. J. Vol. 17, No. 6, pp. 816-824, 2003. https://doi.org/10.1007/BF02983395