DOI QR코드

DOI QR Code

Rayleigh-Ritz procedure for determination of the critical load of tapered columns

  • 투고 : 2012.03.09
  • 심사 : 2013.09.18
  • 발행 : 2014.01.25

초록

EC3 provides several methodologies for the stability verification of members and frames. However, when dealing with the verification of non-uniform members in general, with tapered cross-section, irregular distribution of restraints, non-linear axis, castellated, etc., several difficulties are noted. Because there are yet no guidelines to overcome any of these issues, safety verification is conservative. In recent research from the authors of this paper, an Ayrton-Perry based procedure was proposed for the flexural buckling verification of web-tapered columns. However, in order to apply this procedure, Linear Buckling Analysis (LBA) of the tapered column must be performed for determination of the critical load. Because tapered members should lead to efficient structural solutions, it is therefore of major importance to provide simple and accurate formula for determination of the critical axial force of tapered columns. In this paper, firstly, the fourth order differential equation for non-uniform columns is derived. For the particular case of simply supported web-tapered columns subject to in-plane buckling, the Rayleigh-Ritz method is applied. Finally, and followed by a numerical parametric study, a formula for determination of the critical axial force of simply supported linearly web-tapered columns buckling in plane is proposed leading to differences up to 8% relatively to the LBA model.

키워드

참고문헌

  1. Abaqus (2010), v. 6.10, Dassault Systems/Simulia, Providence, RI, USA.
  2. Baptista, A.M. and Muzeau, J.P. (1998), "Design of tapered compression members according to Eurocode 3", J. Construct. Steel Res., 46(1-3), 146-148. https://doi.org/10.1016/S0143-974X(98)00064-9
  3. CEN (2005), "Eurocode 3, EN-1993-1-1:2005, Eurocode 3: Design of steel structures - Part 1-1: General Rules and Rules for Buildings", European Committee for Standardization, Brussels, Belgium.
  4. Chen, W.F. and Lui, E.M. (1987), Structural Stability - Theory and Implementation, Elsevier Science Publishing Co., New York.
  5. ENV 1993-1-1:1992 (1992), Eurocode 3: Design of steel structures - Part 1-1: General rules and rules for buildings, Brussels.
  6. Ermopoulos, J. (1997), "Equivalent buckling length of non-uniform members", J. Construct. Steel Res., 42(2), 141-158. https://doi.org/10.1016/S0143-974X(97)00010-2
  7. Galambos, T.V. (1998), (editor) Guide to Stability Design Criteria for Metal Structures, (Fifth Edition), John Wiley & Sons Inc.
  8. Hirt, M.A. and Crisinel, M (2001), "Charpentes Metaliques - Conception et Dimensionnement des Halles et Batiments", Traite de Genie Civil, vol. 11, Press Polytechniques et Universitaires Romandes, Lausanne.
  9. Kaehler, R.C., White, D.W. and Kim, Y.D. (2010), Frame Design Using Web-Tapered Members, Design Guide 25, etal Building Manufacturers Association and AISC, Chicago, IL, USA
  10. Lee, G.C., Morrell, M.L. and Ketter, R.L. (1972), Design of Tapered Members, Weld Res. Counc. Bull. No. 173, June, pp. 1-32.
  11. Li, Q.S. (2008), "A stability of non-uniform columns under the combined action of concentrated follower forces and variably distributed loads", J. Construct, Steel Res., 64(3), 367-376. https://doi.org/10.1016/j.jcsr.2007.07.006
  12. Maiorana, E. and Pellegrino, C. (2011), "Linear buckling analysis of welded girder webs with variable thickness", Steel Compos. Struct., Int. J., 11(6), 505-524. https://doi.org/10.12989/scs.2011.11.6.505
  13. Marques, L., Taras, A., Simoes da Silva, L., Greiner, R. and Rebelo, C. (2012), "Development of a consistent design procedure for tapered columns", J. Construct. Steel Res., 72, 61-74. https://doi.org/10.1016/j.jcsr.2011.10.008
  14. Naumes, J. (2009), "Biegeknicken und Biegedrillknicken von Stäben und Stabsystemen auf einheitlicher Grundlage", Ph.D. Thesis, RWTH Aachen, Germany.
  15. Petersen, C. (1993), Stahlbau, Vieweg Verlag, Wiesbaden.
  16. Raftoyiannis, I. and Ermopoulos, J. (2005), "Stability of tapered and stepped steel columns with initial imperfections", Eng. Struct., 27(8), 1248-1257. https://doi.org/10.1016/j.engstruct.2005.03.009
  17. Saffari, H., Rahgozar, R. and Jahanshahi, R. (2008), "An efficient method for computation of effective length factor of columns in a steel gabled frame with tapered members", J. Construct. Steel Res., 64(4),400-406. https://doi.org/10.1016/j.jcsr.2007.09.001
  18. Serna, M.A., Ibanez, J.R. and Lopez, A. (2011), "Elastic flexural buckling of non-uniform members: Closed-form expression and equivalent load approach", J. Construct. Steel Res., 67(7), 1078-1085. https://doi.org/10.1016/j.jcsr.2011.01.003
  19. Simoes da Silva, L., Gervasio, H. and Simoes, R. (2010b), Design of Steel Structures - Part 1-1: General Rules and Rules for Buildings, ECCS.
  20. Simoes da Silva, L., Marques, L. and Rebelo, C. (2010a), "Numerical validation of the general method in EC3-1-1 for prismatic members", J. Construct. Steel Res., 66(4), 575-590. https://doi.org/10.1016/j.jcsr.2009.11.003
  21. Yossif, W.V. (2008), "Elastic critical load of tapered members", J. Eng. Dev., 12(1), March.

피인용 문헌

  1. Experimental study on partially-reinforced steel RHS compression members vol.63, pp.3, 2017, https://doi.org/10.12989/sem.2017.63.3.385
  2. Numerical Nonlinear Buckling Analysis of Tapered Slender Reinforced Concrete Columns vol.17, pp.8, 2019, https://doi.org/10.1007/s40999-019-00395-5
  3. An implementation for 2nd-order M-N coupling and geometric stiffness adaptation in tapered beam-column elements vol.225, pp.None, 2020, https://doi.org/10.1016/j.engstruct.2020.111241