DOI QR코드

DOI QR Code

A Review on Spray Characteristics of Bioethanol and Its Blended Fuels in CI Engines

  • No, Soo-Young (Dept. of Biosystems Engineering, Chungbuk National University)
  • Received : 2014.09.24
  • Accepted : 2014.12.19
  • Published : 2014.12.31

Abstract

This review will be concentrated on the spray characteristics of bioethanol and its derived fuels such as ethanol-diesel, ethanol-biodiesel in compression ignition (CI) engines. The difficulty in meeting the severe limitations on NOx and PM emissions in CI engines has brought about many methods for the application of ethanol because ethanol diffusion flames in engine produce virtually no soot. The most popular method for the application of ethanol as a fuel in CI engines is the blending of ethanol with diesel. The physical properties of ethanol and its derivatives related to spray characteristics such as viscosity, density and surface tension are discussed. Viscosity and density of e-diesel and e-biodiesel generally are decreased with increase in ethanol content and temperature. More than 22% and 30% of ethanol addition would not satisfied the requirement of viscosity and density in EN 590, respectively. Investigation of neat ethanol sprays in CI engines was conducted by very few researchers. The effect of ambient temperature on liquid phase penetration is a controversial topic due to the opposite result between two studies. More researches are required for the spray characteristics of neat ethanol in CI engines. The ethanol blended fuels in CI engines can be classified into ethanol-diesel blend (e-diesel) and ethanol-biodiesel (e-biodiesel) blend. Even though dodecanol and n-butanol are rarely used, the addition of biodiesel as blend stabilizer is the prevailing method because it has the advantage of increasing the biofuel concentration in diesel fuel. Spray penetration and SMD of e-diesel and e-biodiesel decrease with increase in ethanol concentration, and in ambient pressure. However, spray angle is increased with increase in the ethanol percentage in e-diesel. As the ambient pressure increases, liquid phase penetration was decreased, but spray angle was increased in e-diesel. The increase in ambient temperature showed the slight effect on liquid phase penetration, but spray angle was decreased. A numerical study of micro-explosion concluded that the optimum composition of e-diesel binary mixture for micro-explosion was approximately E50D50, while that of e-biodiesel binary mixture was E30B70 due to the lower volatility of biodiesel. Adding less volatile biodiesel into the ternary mixture of ethanol-biodiesel-diesel can remarkably enhance micro-explosion. Addition of ethanol up to 20% in e-biodiesel showed no effect on spray penetration. However, increase of nozzle orifice diameter results in increase of spray penetration. The more study on liquid phase penetration and SMD in e-diesel and e-biodiesel is required.

Keywords

References

  1. G. Knothe, The biodiesel handbook, AOCS press, 2005.
  2. A. Demirbas, Biofuels, Springer, 2009.
  3. S. Y. No, How vegetable oils and their derivatives affect spray characteristics in CI engines-A review, Atomization and Sprays, Vol. 21, No. 1, 2011, pp. 87-105. https://doi.org/10.1615/AtomizSpr.v21.i1.60
  4. S. Y. No, Inedible vegetable oils and their derivatives for alternative diesel fuels in CI engines: A review, Renewable & Sustainable Energy Reviews, Vol. 15, 2011, pp. 131-149. https://doi.org/10.1016/j.rser.2010.08.012
  5. B. M. Masum, H. H. Masjuki, M. A. Kalam, I. M. R. Fattah, S.M. Palash, M.J. Abedin, Effect of ethanolgasoline blend on NOx emission in SI engine, Renewable & Sustainable Energy Reviews, Vol. 24, 2013, pp. 209-222. https://doi.org/10.1016/j.rser.2013.03.046
  6. R. E. H. Sims, W. Mabee, J. N. Saddler, M. Taylor, An overview of second generation biofuel technologies, Bioresource Technology, Vol. 101, 2010, pp.1570-1580. https://doi.org/10.1016/j.biortech.2009.11.046
  7. B. F. Sarrouh, R. R. Philippini, S. S. da Silva, Lignocellulosic Bioethanol Production: Perspectives and Challenges, International Review of Chemical Engineering, Vol. 1, No. 6, 2009, pp. 614-622.
  8. B. M. M. Bomani, D. L. Bulzan, D. I. Centeno-Gomez, R. C. Hendricks, "Biofuels as an Alternative Energy Source for Aviation A Survey" NASA/TM 2009-215587, NASA Glenn Research Center, 2009.
  9. Y. Sun and J. Cheng, Hydrolysis of lignocellulosic materials for ethanol production: a review, Bioresource Technology, Vol. 83, 2002, pp.1-11. https://doi.org/10.1016/S0960-8524(01)00212-7
  10. M. Balat, M. and H. Balat, Recent trends in global production and utlization of bio-ethanol fuel, Applied Energy, Vol. 86, No. 11, pp. 2273-2282.
  11. C. Picclo and F. Bezzo, A techno-economic comparison between two technologies for bioethanol production from lignocelluloses, Biomass and Bioenergy, Vol. 33, 2009, pp. 478-491. https://doi.org/10.1016/j.biombioe.2008.08.008
  12. A. Ganguly, P. K. Chatterjee, A. Dey, Studies on ethanol production from water hyacinth-A review, Renewable & Sustainable Energy Reviews, Vol. 16, 2012, pp. 966-972. https://doi.org/10.1016/j.rser.2011.09.018
  13. H. L. MacLean, L. B. Lave, Evaluating automobile fuel/propulsion system technologies, Progress in Energy and Combustion Science, Vol. 29, 2003, pp. 1-69. https://doi.org/10.1016/S0360-1285(02)00032-1
  14. P. Boggavarapu and R.V. Ravikrishna, A Review on Atomization and Sprays of Biofuels for IC Engine Applications, International Journal of Spray and Combustion Dynamics, Vol. 5, No. 2, 2013, pp. 85-121. https://doi.org/10.1260/1756-8277.5.2.85
  15. E. Sadeghinezhad, S. N. Kazi, F. Sadeghinezhad, A. Badarudin, M. Mehrali, R. Sadri, M. R. Safaeri, A comprehensive literature review of bio-fuel performance in internal combustion engine and relevant costs involvement, Renewable & Sustainable Energy Reviews, Vol. 30, 2014, 29-44. https://doi.org/10.1016/j.rser.2013.09.022
  16. M. Lapuerta, O. Armas, R. Garcia-Contreras, Stability of diesel-bioethanol blends for use in diesel engines, Fuel, Vol. 86, 2007, pp. 1351-1357. https://doi.org/10.1016/j.fuel.2006.11.042
  17. A. C. Hasen, Q. Zhang, P. W. L. Lyne, Ethanol-diesel fuel blends-a review, Bioresource Technology, Vol. 96, 2005, pp. 277-285. https://doi.org/10.1016/j.biortech.2004.04.007
  18. A. H. Lefebvre, A. H., Atomization and Sprays, Hemisphere, 1989.
  19. L. Bayvel, and Z. Orzechowski, Liquid Atomization, Taylor & Francis, 1993.
  20. G. G. Nasr, A. J. Yule and L. Bendig, Industrial Sprays and Atomization, Design, Analysis and Applications, Springer, 2002.
  21. S. Y. No, Prediction of Maximum Liquid-phase Penetration in Diesel Spray: A Review, Journal of ILASS-Korea, Vol. 13, No. 3, 2008, pp. 117-125.
  22. P. Spiekemann, S. Jerzembeck, C. Felsch, S. Vogel, M. Gauding, N. Peters, Experimental and Numerical Investigation of Common-Rail Ethanol Sprays at Diesel Enginelike Conditions, Atomization and Sprays, Vol.19, No.4, 2009, pp. 357-387. https://doi.org/10.1615/AtomizSpr.v19.i4.40
  23. S. Kumar, J. H. Cho, J. Park, I. Moon, Advances in diesel-alcohol blends and their effects on the performance and emissions of diesel engines, Renewable & Sustainable Energy Reviews, Vol. 22, 2013, pp. 46-72. https://doi.org/10.1016/j.rser.2013.01.017
  24. D-G, Li, Z. Huang, X. Lu, W-G, Zhang, J-G. Yang, Physico-chemical properties of ethanol-diesel blends fuel and its effect on performance and emission of diesel engines, Renewable Energy, Vol. 30, 2005, pp. 967-976. https://doi.org/10.1016/j.renene.2004.07.010
  25. Z. Q. Chen, X. X. Ma, S. T. Yu, Y. N. Guo, J. S. Liu, Physical-Chemical Properties of Ethanol-Diesel Blend Fuel and Its Effect on the Peformance and Emissions of a Turbocharged Diesel Engine, International Journal of Automotive Technology, Vol. 10, No. 3, 2009, pp. 297-303. https://doi.org/10.1007/s12239-009-0034-0
  26. M. Lapuerta, R. Garcia-Contreras, J. Campos-Fernandez, M. P. Dorado, Stability, Lubricity, Viscosity, and Cold-flow Properties of Alcohol-Diesel Blends, Energy Fuels, Vol. 24, 2010, pp. 4497-4502. https://doi.org/10.1021/ef100498u
  27. B. E. Poing, J. M. Prausnitz, J. P. O'Connell, The Properties of Gases and Liquids. Fifth ed. McGraw-Hill, 2001, pp. 9.77-9.80.
  28. E. Torres-Jimenez, M. S. Jerman, A. Gregorc, I. Lisec, M. P. Dorado, B. Kegl, Physical and chemical properties of ethanol-diesel fuel blends, Fuel, Vol. 90, 2011, pp. 795-802. https://doi.org/10.1016/j.fuel.2010.09.045
  29. S. H. Park, I. M. Youn, Y. Lim, C. S. Lee, Effect of Bioethanol Blended Diesel Fuel and Engine Load on Spray, Combustion, and Emissions Characteristics in a Compression Ignition Engine, Energy Fuels, Vol. 26, 2012, pp. 5135-5145. https://doi.org/10.1021/ef300894h
  30. S. Parala, M. K. Le, S. Kook, E. R. Hawkes, Imaging Diagnostics of ethanol port fuel injection sprays for automobile engine applications, Applied Thermal Engineering, Vol. 52, 2013, pp. 24-37. https://doi.org/10.1016/j.applthermaleng.2012.11.007
  31. R. Stone, Introduction to Internal Combustion Engines, 2nd Ed., Macmillan, 1992, p. 88.
  32. H. J. Kim, H. K. Suh, S. H. Park, C. S. Lee, An Experimental and Numerical Investigation of Atomization Characteristics of Biodiesel, Dimethyl Ether, and Biodieselethanol Blended Fuel, Energy Fuels, Vol. 22, 2008, pp. 2091-2098. https://doi.org/10.1021/ef700692w
  33. P. I. Lee, X. Xie, M. C. Lai, Effect of ethanol-biodiesel blend ratio on fuel properties and spray behaviors, ILASS-Americas, 23rd Annual Conf. on Liquid Atomization and Spray Systems,Ventura, CA, May 2011.
  34. P. Kwanchareon, A. Luengnaruemitchai, S. Jai-In, Solubility of a diesel-ethanol blend, its fuel properties and its emission characteristics from diesel engine, Fuel, Vol. 86, 2007, pp. 1053-1061. https://doi.org/10.1016/j.fuel.2006.09.034
  35. N. Ashgriz, Handbook of Atomization and Sprays: theory and applications, Springer, 2011.
  36. P. Spiekermann, S. Jerzembeck, S. Vogel, C. Felsch, N. Peters, Experimental and Numerical Investigation of Common-Rail Ethanol Sprays at Diesel Engine-Like Conditions, ILASS-Americas, 20th Annual Conf. on Liquid Atomization and Spray Systems, Chicago. IL., May 2007.
  37. M. A. Reddemann, F. Mathieu, D. Martin, R. Kneer, Experimental Investigation of Spray Propagation and Mixture Formation of Tailor-Made Fuels under Engine-Relevant Conditions, ICLASS 2009, 11th Triennial Int'l Conf. on Liquid Atomization and Spray Systems, Vail, Colorado, USA, July 2009.
  38. G. Nagarajan, A. Rao, T. Jagadeesan, S. Renganara-yanan, Review of Ethanol in Compression Ignition Engine, Institute for Energy Studies, Anna University, India.
  39. C. F. Lee, K. T. Wang, W. L. Cheng, Atomization Char-acteristics of Multi-component Bio-fuel Systems under Micro-explosion Conditions, SAE paper 2012-012-1740, 2012.
  40. H. Rahimi, B. Ghobadian, T. Yusaf, G. Najafi, M. Khatamifar, Diesterol: An environment-friendly IC engine fuel, Renewable Energy, Vol. 34, 2009, pp. 335-342. https://doi.org/10.1016/j.renene.2008.04.031
  41. S. Fernando and M. Hanna, Development of a Novel Biofuel Blending Using Ethanol-biodiesel-Diesel Microemulsions: EB-Diesel, Energy Fuels, Vol. 18, No. 6, 2004, pp. 1695-1703. https://doi.org/10.1021/ef049865e
  42. G. Gonca, Investigation of the effects of steam injection on performance and NO emissions of a diesel engine running with ethanol-diesel blend, Energy Conversion and Management, Vol. 77, 2014, pp. 450-457. https://doi.org/10.1016/j.enconman.2013.09.031
  43. M. Lapuerta, O. Armas, R. Garcia-Contreras, Effect of Ethanol on Blending Stability and Diesel Engine Emissions, Energy Fuels, Vol. 23, 2009, pp. 4343-4354. https://doi.org/10.1021/ef900448m
  44. J. Liu, S. Liu, Y. Wei, Y. Li, G. Li, H. He, Diesehol CI Engine Performance. Regulated and Nonregulated Emissions Characteristics, Energy Fuels, Vol. 24, 2010, pp. 828-833. https://doi.org/10.1021/ef900930a
  45. S. A. Shahir, H. H. Masjuki, M. A. Kalam, A. Imran, I. M. Rizwanul Fattah, A. Sanjid, Feasibility of dieselbiodiesel-ethanl/bioethanol blend as existing CI engine fuel: An assessment of properties, material compatibility, safety and combustion, Renewable & Sustainable Energy Reviews, Vol. 32, 2014, pp. 379-395. https://doi.org/10.1016/j.rser.2014.01.029
  46. A. V. Pantar, K. C. Corkwell, E Diesel: A Viable Alternative Fuel, SAE paper 2004-28-0074, 2004.
  47. M. J. Cardenas, D. Cordes, R. Kneer, Experimental investigation of spray characteristics of fuel blends having low cetane number and high volatility in a diesel fuel injection system, ICLASS 2012, 12th Int'l Conf. on Liquid Atomization and Spray Systems. Heidelberg. Germany, Sept. 2-6, 2012.
  48. Y. Di, C. S. Sheung, Z. Huang, Comparison of the Effect of Biodiesel-Diesel and Ethanol-Diesel on the Particulate Emissions of a Direct Injection Diesel Engine, Aerosol Science and Technology, Vol. 43, 2009, pp. 455-465. https://doi.org/10.1080/02786820902718078
  49. C. S. Cheung, Y. Di, Z. Huang, Experimental Investigation of regulated and unregulated emissions from a diesel engine fueled with ultralow-sulfur diesel fuel blended with ethanol and dodecanol, Atmospheric Environment, Vol. 42, 2008, pp.8843-8851. https://doi.org/10.1016/j.atmosenv.2008.09.009
  50. X. Wang, C. S. Cheug, Y. Di, Z. Huang, Diesel engine gaseous and particle emissions fueled with dieseloxygenate blends, Fuel, Vol. 94, 2012, pp. 317-323. https://doi.org/10.1016/j.fuel.2011.09.016
  51. J. Huang, Y. Wang, S. Li, A. P. Roskilly, H. Yu, H. Li, Experimental investigation on the performance and emissions of a diesel engine fueled with ethanol-diesel blends, Applied Thermal Engineering, Vol. 29, 2009, pp. 2484-2490. https://doi.org/10.1016/j.applthermaleng.2008.12.016
  52. H. Chen, J. X. Wang, S.-J. Shuai, X.-L. An, W.-M. Chen, Effects of Ethanol in Ester-Ethanol-Diesel Blended Fuelson Spray Behavior and PM Emission, SAE paper 2006-01-0236, 2006.
  53. S. H. Park, S. H. Kim, C. S. Lee, Mixing Stability and Spray Behavior Characteristics of Diesel-Ethanol-Methyl Ester Blended Fuels in Common-rail Diesel Injection System, Energy Fuels, Vol. 23, 2009, pp. 5228-5235. https://doi.org/10.1021/ef9004847
  54. S. H. Park, I. M. Youn, C. S. Lee, Influence of ethanol blends on the combustion performance and exhaust emission characteristics of a four-cylinder diesel engine at various engine loads and injection timings, Fuel, Vol. 90, 2011, pp. 748-755. https://doi.org/10.1016/j.fuel.2010.08.029
  55. S. Y. No, Definition and Correlation for Spray Angle in Non-Reacting Diesel Fuel Sprays, ILASS-Korea Journal, Vol. 11, No. 4, 2006, pp. 244-250.
  56. K. Jeong, S. H. Park, C. S. Lee, Injection spray and emissions characteristics in a diesel engine using dieselbioethanol blended fuel, ILASS-Europe 2011. 24th European conf. on Liquid Atomization and Spray Systems, Estoril, Portugal, Sept. 2011.
  57. C. Shen, W. L. Cheng, K. Wang, C. F. Lee, Estimating the Secondary Droplet Size Distribution after Micro-Explosion of Bio-fuel Droplets, ILASS-Americas 2010, 22nd Annual Conf. on Liquid Atomization and Spray Systems, Cincinati, OH, May, 2010.
  58. S. H. Park, H. K. Suh, C. S. Lee, Nozzle flow and atomization characteristics of ethanol blended biodiesel fuel, Renewable Energy, Vol. 35, 2010, pp. 144-150. https://doi.org/10.1016/j.renene.2009.06.012
  59. S. H. Park, H. K. Suh, C. S. Lee, Effect of Bioethanol-Biodiesel Blending Ratio on Fuel Spray Behavior and Atomization Characteristics, Energy Fuels, Vol. 23, 2009, pp.4092-4098. https://doi.org/10.1021/ef900068a

Cited by

  1. A Review on Spray Characteristics of Biobutanol and Its Blended Fuels in IC engines vol.21, pp.3, 2016, https://doi.org/10.15435/JILASSKR.2016.21.3.144