The Journal of Advanced Prosthodontics

  • 제5권4호
  • /
  • Pages.464-470
  • /
  • 2013
  • /
  • 2005-7806(pISSN)
  • /
  • 2005-7814(eISSN)
대한치과보철학회 (The Korean Academy of Prosthodonitics)
권호 표지
DOI QR코드

DOI QR Code

Degree of conversion of two dual-cured resin cements light-irradiated through zirconia ceramic disks

  • Kim, Min-Jeong (Department of Medical & Biological Engineering, Graduate School, Kyungpook National University) ;
  • Kim, Kyo-Han (Department of Dental Biomaterials, School of Dentistry, and Institute for Biomaterials Research & Development, Kyungpook National University) ;
  • Kim, Young-Kyung (Department of Conservative Dentistry, School of Dentistry, Kyungpook National University) ;
  • Kwon, Tae-Yub (Department of Dental Biomaterials, School of Dentistry, and Institute for Biomaterials Research & Development, Kyungpook National University)
  • 투고 : 2013.06.23
  • 심사 : 2013.11.05
  • 발행 : 2013.11.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

PURPOSE. The aim of this Fourier transform infrared (FTIR) spectroscopic study was to measure the degree of conversion (DC) of dual-cured resin cements light-irradiated through zirconia ceramic disks with different thicknesses using various light-curing methods. MATERIALS AND METHODS. Zirconia ceramic disks (KT12) with three different thicknesses (1.0, 2.0, and 4.0 mm) were prepared. The light transmittance of the disks was measured using ultraviolet visible near-infrared spectroscopy. Four different light-curing protocols were used by combining two curing light modes (Elipar TriLight (standard mode) and bluephase G2 (high power mode)) with light-exposure times of 40 and 120 seconds. The DCs of the two dual-cured resin cements (Duo-Link and Panavia F2.0) light-irradiated through the disks was analyzed at three time intervals (3, 7, and 10 minutes) by FTIR spectroscopy. The data was analyzed using repeated measures ANOVA (${\alpha}$=.05).Two-way ANOVA and Tukey post hoc test were used to analyze the 10 minute DC results. RESULTS. The 1.0 mm thick disk exhibited low light transmittance (<25%), and the transmittance decreased considerably with increasing disk thickness. All groups exhibited significantly higher 10 minute DC values than the 3 or 7 minute values (P<.05), but some exceptions were observed in Duo-Link. Two-way ANOVA revealed that the influence of the zirconia disk thickness on the 10 minute DC was dependent on the light-curing methods (P<.001). This finding was still valid even at 4.0 mm thickness, where substantial light attenuation took place. CONCLUSION. The curing of the dual-cured resin cements was affected significantly by the light-curing technique, even though the additional chemical polymerization mechanism worked effectively.

키워드

참고문헌

  1. Attia A, Lehmann F, Kern M. Influence of surface conditioning and cleaning methods on resin bonding to zirconia ceramic. Dent Mater 2011;27:207-13. https://doi.org/10.1016/j.dental.2010.10.004
  2. Matinlinna JP, Lassila LV. Enhanced resin-composite bonding to zirconia framework after pretreatment with selected silane monomers. Dent Mater 2011;27:273-80. https://doi.org/10.1016/j.dental.2010.11.002
  3. Piconi C, Maccauro G. Zirconia as a ceramic biomaterial. Biomaterials 1999;20:1-25. https://doi.org/10.1016/S0142-9612(98)00010-6
  4. Piwowarczyk A, Lauer HC, Sorensen JA. The shear bond strength between luting cements and zirconia ceramics after two pre-treatments. Oper Dent 2005;30:382-8.
  5. Roediger M, Gersdorff N, Huels A, Rinke S. Prospective evaluation of zirconia posterior fixed partial dentures: fouryear clinical results. Int J Prosthodont 2010;23:141-8.
  6. Blatz MB, Sadan A, Kern M. Resin-ceramic bonding: a review of the literature. J Prosthet Dent 2003;89:268-74. https://doi.org/10.1067/mpr.2003.50
  7. Tanaka R, Fujishima A, Shibata Y, Manabe A, Miyazaki T. Cooperation of phosphate monomer and silica modification on zirconia. J Dent Res 2008;87:666-70. https://doi.org/10.1177/154405910808700705
  8. Vagkopoulou T, Koutayas SO, Koidis P, Strub JR. Zirconia in dentistry: Part 1. Discovering the nature of an upcoming bioceramic. Eur J Esthet Dent 2009;4:130-51.
  9. Baldissara P, Llukacej A, Ciocca L, Valandro FL, Scotti R. Translucency of zirconia copings made with different CAD/ CAM systems. J Prosthet Dent 2010;104:6-12. https://doi.org/10.1016/S0022-3913(10)60086-8
  10. El-Mowafy OM, Rubo MH. Influence of composite inlay/ onlay thickness on hardening of dual-cured resin cements. J Can Dent Assoc 2000;66:147.
  11. Kim MJ, Kim YK, Kim KH, Kwon TY. Shear bond strengths of various luting cements to zirconia ceramic: surface chemical aspects. J Dent 2011;39:795-803. https://doi.org/10.1016/j.jdent.2011.08.012
  12. Aguiar TR, Di Francescantonio M, Arrais CA, Ambrosano GM, Davanzo C, Giannini M. Influence of curing mode and time on degree of conversion of one conventional and two self-adhesive resin cements. Oper Dent 2010;35:295-9. https://doi.org/10.2341/09-252-L
  13. Yan YL, Kim YK, Kim KH, Kwon TY. Changes in degree of conversion and microhardness of dental resin cements. Oper Dent 2010;35:203-10. https://doi.org/10.2341/09-174-L
  14. Bayne SC. Dental biomaterials: where are we and where are we going? J Dent Educ 2005;69:571-85.
  15. Gerth HU, Dammaschke T, Züchner H, Schäfer E. Chemical analysis and bonding reaction of RelyX Unicem and Bifix composites-a comparative study. Dent Mater 2006;22:934-41. https://doi.org/10.1016/j.dental.2005.10.004
  16. Ferracane JL, Greener EH. The effect of resin formulation on the degree of conversion and mechanical properties of dental restorative resins. J Biomed Mater Res 1986;20:121-31. https://doi.org/10.1002/jbm.820200111
  17. Vrochari AD, Eliades G, Hellwig E, Wrbas KT. Curing efficiency of four self-etching, self-adhesive resin cements. Dent Mater 2009;25:1104-8. https://doi.org/10.1016/j.dental.2009.02.015
  18. Dias MC, Piva E, de Moraes RR, Ambrosano GM, Sinhoreti MA, Correr-Sobrinho L. UV-Vis spectrophotometric analysis and light irradiance through hot-pressed and hot-pressed-veneered glass ceramics. Braz Dent J 2008;19:197-203.
  19. Brodbelt RH, O'Brien WJ, Fan PL. Translucency of dental porcelains. J Dent Res 1980;59:70-5. https://doi.org/10.1177/00220345800590011101
  20. Leonard DL. Light-emitting diode curing lights, Part II. J Esthet Restor Dent 2003;15:251-5. https://doi.org/10.1111/j.1708-8240.2003.tb00293.x
  21. Kim YK, Kim SK, Kim KH, Kwon TY. Degree of conversion of dual-cured resin cement light-cured through three fibre posts within human root canals: an ex vivo study. Int Endod J 2009;42:667-74. https://doi.org/10.1111/j.1365-2591.2009.01565.x
  22. Pegoraro TA, da Silva NR, Carvalho RM. Cements for use in esthetic dentistry. Dent Clin North Am 2007;51:453-71. https://doi.org/10.1016/j.cden.2007.02.003
  23. Faria-e-Silva AL, Moraes RR, Ogliari FA, Piva E, Martins LR. Panavia F: the role of the primer. J Oral Sci 2009;51:255-9. https://doi.org/10.2334/josnusd.51.255
  24. Van Landuyt KL, Snauwaert J, De Munck J, Peumans M, Yoshida Y, Poitevin A, Coutinho E, Suzuki K, Lambrechts P, Van Meerbeek B. Systematic review of the chemical composition of contemporary dental adhesives. Biomaterials 2007; 28:3757-85. https://doi.org/10.1016/j.biomaterials.2007.04.044
  25. Kwon TY, Bagheri R, Kim YK, Kim KH, Burrow MF. Cure mechanisms in materials for use in esthetic dentistry. J Investig Clin Dent 2012;3:3-16. https://doi.org/10.1111/j.2041-1626.2012.00114.x
  26. Mills RW, Jandt KD, Ashworth SH. Dental composite depth of cure with halogen and blue light emitting diode technology. Br Dent J 1999;186:388-91.
  27. Rueggeberg FA, Caughman WF. The influence of light exposure on polymerization of dual-cure resin cements. Oper Dent 1993;18:48-55.
  28. Arrais CA, Giannini M, Rueggeberg FA. Effect of sodium sulfinate salts on the polymerization characteristics of dualcured resin cement systems exposed to attenuated light-activation. J Dent 2009;37:219-27. https://doi.org/10.1016/j.jdent.2008.11.016
  29. Pazin MC, Moraes RR, Gonçalves LS, Borges GA, Sinhoreti MA, Correr-Sobrinho L. Effects of ceramic thickness and curing unit on light transmission through leucite-reinforced material and polymerization of dual-cured luting agent. J Oral Sci 2008;50:131-6. https://doi.org/10.2334/josnusd.50.131
  30. Jakubiak J, Allonas X, Fouassier JP, Sionkowska A, Andrzejewska E, Linden LÅ, Rabek JF. Camphorquinone- amines photoinitating systems for the initiation of free radical polymerization. Polymer 2003;44:5219-26. https://doi.org/10.1016/S0032-3861(03)00568-8
  31. Kameyama A, Hatayma H, Kato J, Haruyama A, Teraoka H, Takase Y, Yoshinari M, Tsunoda M. Spectral characteristics of light-curing units and dental adhesives. J Photopolym Sci Technol 2011;24:411-6. https://doi.org/10.2494/photopolymer.24.411
  32. Miletic V, Santini A. Micro-Raman spectroscopic analysis of the degree of conversion of composite resins containing different initiators cured by polywave or monowave LED units. J Dent 2012;40:106-13. https://doi.org/10.1016/j.jdent.2011.10.018

피인용 문헌

  1. Meta-analysis of Bonding Effectiveness to Zirconia Ceramics vol.93, pp.4, 2014, https://doi.org/10.1177/0022034514524228
  2. Setting Reaction of Dental Resin-Modified Glass Ionomer Restoratives as a Function of Curing Depth and Postirradiation Time vol.2015, pp.2314-4939, 2015, https://doi.org/10.1155/2015/462687
  3. The effect of 4,4'-bis(N,N-diethylamino) benzophenone on the degree of conversion in liquid photopolymer for dental 3D printing vol.7, pp.5, 2015, https://doi.org/10.4047/jap.2015.7.5.386
  4. Additional chemical polymerization of dual resin cements: reality or a goal to be achieved? vol.45, pp.3, 2016, https://doi.org/10.1590/1807-2577.12415
  5. Effect of different power settings of Er,Cr:YSGG laser before or after tribosilicatization on the microshear bond strength between zirconia and two types of cements pp.1435-604X, 2017, https://doi.org/10.1007/s10103-017-2343-2
  6. Influence of pre-heating and ceramic thickness on physical properties of luting agents vol.16, pp.4, 2018, https://doi.org/10.1177/2280800018782842
  7. Influence of monolithic lithium disilicate and zirconia thickness on polymerization efficiency of dual-cure resin cements pp.14964155, 2018, https://doi.org/10.1111/jerd.12390
  8. Evaluation of Dual-Cure Resin Cement Polymerization under Different Types and Thicknesses of Monolithic Zirconia vol.2019, pp.2314-6141, 2019, https://doi.org/10.1155/2019/4567854
  9. Effect of Different Thicknesses of Pressable Ceramic Veneers on Polymerization of Light-cured and Dual-cured Resin Cements vol.16, pp.5, 2013, https://doi.org/10.5005/jp-journals-10024-1688
  10. Effect of monolithic zirconia on the degree of conversion of two resin cements analyzed by FT-IR/ATR spectroscopy vol.30, pp.9, 2013, https://doi.org/10.1080/01694243.2015.1133199
  11. 지르코니아 투명도 및 두께에 따른 레진 시멘트의 중합률 vol.38, pp.3, 2013, https://doi.org/10.14347/kadt.2016.38.3.193
  12. In Vitro Cytotoxicity of Self-Adhesive Dual-Cured Resin Cement Polymerized Beneath Three Different Cusp Inclinations of Zirconia vol.2019, pp.None, 2013, https://doi.org/10.1155/2019/7404038