DOI QR코드

DOI QR Code

Automated nonlinear design of reinforced concrete D regions

  • Amini Najafian, Hamidreza (Department of Civil and Environmental Engineering, Imperial College London) ;
  • Vollum, Robert L. (Department of Civil and Environmental Engineering, Imperial College London)
  • Received : 2012.08.13
  • Accepted : 2013.03.06
  • Published : 2013.04.10

Abstract

This paper proposes a novel iterative procedure for the design of planar reinforced concrete structures in which the reinforcement is designed for stresses calculated in a nonlinear finite element analysis. The procedure is intended as an alternative to strut and tie modeling for the design of complex structures like deep beams with openings. Practical reinforcement arrangements are achieved by grouping the reinforcement into user defined horizontal and vertical bands. Two alternative strategies are proposed for designing the reinforcement which are designated A and B. Design constraints are specified in terms of permissible stresses and strains in the reinforcement and strains in the concrete. A case study of a deep beam with an opening is presented to illustrate the method. Comparisons are made between design strategies A and B of which B is shown to be most efficient. The resulting reinforcement weights are also shown to compare favorably with those previously reported in the literature.

Keywords

References

  1. ACI Committee 318 (2011), Building code requirements for structural concrete and commentary, ACI 318- 11 and ACI 318R-11, American Concrete Institute, Farmington Hills, Michigan.
  2. ACI-ASCE (2010), Joint ACI-ASCE Committee 445, SP-273, Further Examples for the Design of Structural Concrete with Strut-and-Tie Models, American Concrete Institute, Farmington Hills, Michigan.
  3. Amini Najafian, H. (2011), "Nonlinear optimisation of reinforcement design for reinforced concrete structures loaded in plane stress", PhD Thesis, Department of Civil and Environmental Engineering, Imperial College London.
  4. Bentz, E.C. (2000), "Sectional analysis of reinforced concrete members", PhD Thesis, Department of Civil Engineering, University of Toronto.
  5. BSI (2004), European Standard EN-1992-1-1:2004, Eurocode 2: Design of Concrete Structures, Part 1, General Rules and Rules for Buildings, British Standard Institution, London.
  6. Collins, M.P. and Porasz, A. (1989), "Shear design for high-strength concrete", Comite Euro-International du Beton, Bulletin d'Information, 193, 77-83.
  7. Collins, M.P., Bentz, E.C., Sherwood, E.G. and Xie, L. (2008), "An adequate theory for the shear strength of reinforced concrete structures", Mag. Concr. Res., 60, 635-650. https://doi.org/10.1680/macr.2008.60.9.635
  8. CSA (2004), Design of Concrete Structures, CSA Standard A23.3-04, Canadian Standards Association, Ottawa.
  9. DIANA (2007), Finite Element Analysis User's Manual, Release 9.2, TNO DIANA BV, Delft, The Netherlands.
  10. Fernandez Ruiz, M. and Muttoni, A. (2007), "On development of suitable stress fields", ACI Struct. J., 104, 495-502.
  11. Fib (2011), Design examples for strut-and-tie models, fib Bulletin No. 61. fib, Lausanne, Switzerland.
  12. Hong, S.G., Hong, N.K. and Jang, S.K. (2011), "Deformation capacity of structural concrete in disturbed regions", ACI Struct. J., 108(3), 267-276.
  13. Hsu, T.C. (1993), Unified Theory of Reinforced Concrete, CRC Press Inc., Boca Raton, Florida, USA.
  14. Kuchma, D., Yindeesuk, S. and Tjhin, T. (2010), "Large propped cantilever beam with opening, In. SP-273, Further examples for the design of structural concrete with strut-and-tie models", ACI, Farmington Hills, Michigan.
  15. Kwak, H.G. and Noh, S.H. (2006), "Determination of strut-and-tie models using evolutionary structural optimization", Eng. Struct., 28(10), 1440-1449. https://doi.org/10.1016/j.engstruct.2006.01.013
  16. Park, J.W., Yindeesuk, S., Tjhin, T.N. and Kuchma, D.A. (2010), "Automated finite element validation of complex regions designed by the strut-and-tie method", ASCE J. Struct. Eng., 136(2), 203-210. https://doi.org/10.1061/(ASCE)0733-9445(2010)136:2(203)
  17. Perera, R. and Vique, J. (2009), "Strut-and-tie modelling of reinforced concrete beams using genetic algorithms optimization", Const. Build. Mater., 23, 2914-2925. https://doi.org/10.1016/j.conbuildmat.2009.02.016
  18. Schlaich, J., Schäfer, K. and Jennewein, M. (1987), "Toward a consistent design of structural concrete", Prestressed Conc. Inst. J., 32(3), 75-150
  19. Tabatabai, S.M.R. (1996), "Finite element-based elasto-plastic optimum reinforcement dimensioning of spatial concrete panel structures", Doctoral dissertation, Institute of Structural Engineering, Swiss Federal Institute of Technology (ETH Zurich), also published by BirkhaEuser Verlag, Basel.
  20. Tabatabai, S.M.R. and Mosalam, K.M. (2001), "Computational platform for non-linear analysis/ optimal design of reinforced concrete structures", Eng. Comput., 18, 726-744. https://doi.org/10.1108/EUM0000000005785
  21. Tjhin, T.N. and Kuchma, D.A. (2002), "Computer-based tools for design by strut-and-tie method: advances and challenges", ACI Struct. J., 99, 586-594.
  22. Vecchio, F.J. (1990), "Reinforced concrete membrane element formulations", ASCE J. Struct. Eng., 116(3), 730-750. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:3(730)
  23. Vecchio, F.J. and Collins, M.P. (1986), "The modified compression field theory for reinforced concrete elements subjected to shear", ACI J., 83, 219-231.

Cited by

  1. Comparative assessment of finite-element and strut and tie based design methods for deep beams vol.65, pp.16, 2013, https://doi.org/10.1680/macr.13.00006
  2. Analysis of outrigger-braced reinforced concrete supertall buildings: Core-supported and tube-in-tube lateral systems pp.15417794, 2019, https://doi.org/10.1002/tal.1567