DOI QR코드

DOI QR Code

주철금형주조용 도형재의 적용성 평가

Evaluation on the Applicability of Refractory Coatings to Metal Mold for Cast Iron

  • 서금희 (한국기술교육대학교 에너지.신소재.화학공학부) ;
  • 김기영 (한국기술교육대학교 에너지.신소재.화학공학부) ;
  • 문병문 (한국생산기술연구원 주조공정연구그룹)
  • Seo, Kum-Hee (School of Energy, Materials and Chemical Engineering, Korea University of Technology and Education) ;
  • Kim, Ki-Young (School of Energy, Materials and Chemical Engineering, Korea University of Technology and Education) ;
  • Moon, Byung-Moon (Liquid Processing & Casting Technology R/D Group, Korea Institute of Industrial Technology)
  • 투고 : 2012.03.23
  • 심사 : 2012.06.22
  • 발행 : 2012.06.30

초록

A series of refractory mold coatings were applied to cast iron specimens, and their resistances to wear and spalling were investigated. Tests were carried out with own made measures, and also a calculation was tried for the comparison of a part of results like spalling. Worn width by scrubbing the indenter on the coating layer increased significantly at high temperature. Temperature increasing rate across the specimen when the coating side was exposed to $1000^{\circ}C$ was in the range of $14.5{\sim}75.8^{\circ}C$/sec mm, and specimens with thicker coating layer showed lower temperature increase. Severe spalling of coated layer was observed after heating the specimen, and it was able to confirm by calculation using a commercial code.

키워드

참고문헌

  1. ASM International, ASM Handbook, Vol. 15 (1988) 601-603
  2. A. A. Golovnya and I. V. Matveenko: Litejnoe Proizvodstvo, "Experience on refractory coatings using with a filler of technogenic origination for foundry molds and cores", 4(2002) 12
  3. M. Joyce, M. Rebros and S. Ramrattan: International Journal of Metalcasting, "Adapting more progressive refractory coating measurement controls", 2(2008) 29-39
  4. M. Jin, M. Fan, B. Zhang, Y. Wu and J. Wang: Special Casting and Nonferrous Alloys, "Application of Diatomite Coating in Centrifugal Casting Nodular Cast-iron Tube with Thermal Mold Method", 31 (2011) 67-69
  5. H. Jafari, M. H. Idris, A. Ourdjini, H. R. B. Rad, S. S. K Ardestani and V. Ahmadshoar: Advanced Materials Research, "Effect of mould runner and coating on graphite nodule characteristics and hardness of thin wall ductile iron", 264-265 (2011) 266-271 https://doi.org/10.4028/www.scientific.net/AMR.264-265.266
  6. K. Nyamekye, D. Askeland, S. Wei, R. C. Voigt, R. P. Pischel, W. Rasmussen and C. Ramsay: Trans. AFS, "A Review of Permanent Mold Coatings and Their Effect on Heat Transfer in the Mold", 102 (1994) 869-876
  7. S. Wei, J. Dillingham, M. Jiranek, K. Nyamekye, C. W. Ramsay, D. R. Askeland and R. Pischel: Trans. AFS, "Influence of Mold Coating on Heat Transport in Permanent Mold Casting Process", 104 (1996) 251-262
  8. M. N. Turgut, M. N. Demir, M. H. and F. Yigit: Advanced Materials Research, "Effect of mold coating on shell morphology in solidification", 445 (2012) 325-330 https://doi.org/10.4028/www.scientific.net/AMR.445.325
  9. E. Guo, Q. Zheng and T. Jing: Materials Science Forum, "Numerical simulation of solidification of thick-wall stainless steel pipe in horizontal centrifugal casting process", 706-709 (2012) 1427-1432