한국정밀공학회지 (Journal of the Korean Society for Precision Engineering)

  • 제28권3호
  • /
  • Pages.377-382
  • /
  • 2011
  • /
  • 1225-9071(pISSN)
  • /
  • 2287-8769(eISSN)
한국정밀공학회 (Korean Society for Precision Engineering)
권호 표지

원형소재 다단 형상인발 공정설계 프로그램

Process Design Program for Multistage Profile Drawing from Round Material

  • 김성민 (부산대학교 대학원 정밀기계공학과) ;
  • 이상곤 (한국생산기술연구원 대경권지역본부 녹색전환기술센터) ;
  • 이태규 (부산대학교 대학원 정밀기계공학과) ;
  • 이선봉 (계명대학교 기계자동차공학부) ;
  • 김병민 (부산대학교 기계공학부)
  • Kim, Sung-Min (Graduate School of Precision Manufacturing System Division, Pusan National Univ.) ;
  • Lee, Sang-Kon (Green Transformation Technology Center, Daegyeong Regional Division, KITECH) ;
  • Lee, Tae-Kyu (Graduate School of Precision Manufacturing System Division, Pusan National Univ.) ;
  • Lee, Seon-Bong (Faculty of Mechanical and Automotive Engineering, Keimyung Univ.) ;
  • Kim, Byung-Min (School of Mechanical Engineering, Pusan National Univ.)
  • 투고 : 2010.11.24
  • 심사 : 2011.01.08
  • 발행 : 2011.03.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Up to now, process design of multistage profile drawing from initial round material is performed through trial-and-error based on experience of industrial experts. This means the increase in production cost and excessive time consuming. In this study, process design program was developed for multistage profile drawing from initial round material. The program was made using VisualLISP. Therefore, the program can be operated by AutoCAD program. In order to verify the effectiveness of the program, two stage profile drawing process for producing heavy duty guide rail was design by using the program. In addition FE analysis and profile drawing experiment were performed. As a result, the program can be used in order to design profile drawing process design.

키워드

Acknowledgement

Supported by : 한국연구재단

References

  1. Kim, Y. C., Kim, D. J. and Kim, B. M., "Intermediate Die Design System for The Multi-stage Drawing Process," Trans. NAMRI/SME, Vol. 28, pp. 69-74, 2000.
  2. Lee, S. K., Lee, S. B. and Kim, B. M., "Development of Intermediate Die Shape Design Program for Multipass Shape Drawing by Using VisualLISP," Official J. of Korean Society for Technology of Plastictiy, Vol. 19, No. 4, pp. 244-247, 2010.
  3. Brucker, M., Keller, D. and Reissner, J., "Computer- Aided Drawing of Profile from Round and Square Bar," Annals of the CIRP, Vol. 37, No. 1, pp. 247-250, 1988. https://doi.org/10.1016/S0007-8506(07)61628-X
  4. Yoshida, K. and Tuihiji, S., "Multiple Drawing of Rails for Linear Motion Guide," Proc. the 7th ICTP, pp. 367-372, 2002.
  5. Lee, S. K., Lee, J. E., Lee, T. K., Lee, S. B. and Kim, B. M., "Process Design of Multi-stage Shape Drawing Process for Cross Roller Guide," J. of the KSPE, Vol. 26, No. 11, pp. 124-130, 2009.
  6. Kwon, H. H. and Lee, B. K., "Development of Automatic Program for Drawing Die Design," Trans. of the KSMTE, Vol. 14, No. 3, pp. 60-66, 2005.
  7. Lee, T. K., Lee, C. J., Lee, S. K. and Kim, B. M., "Prediction of Drawing Load in The Shape Drawing Process," Official J. of Korean Society for Technology of Plastictiy, Vol. 18, No. 4, pp. 323-328, 2009.
  8. Geleji, A., "Bildsame Formung der Metalle in Rechnung und Versuch (II)," Akademine Verlag GmbH, p. 10,1960.