DOI QR코드

DOI QR Code

Maximum concrete stress developed in unconfined flexural RC members

  • Ho, J.C.M. (Department of Civil Engineering, The University of Hong Kong) ;
  • Pam, H.J. (Department of Civil Engineering, The University of Hong Kong) ;
  • Peng, J. (Department of Civil Engineering, The University of Hong Kong) ;
  • Wong, Y.L. (Department of Civil and Structural Engineering, The Hong Kong Polytechnic University)
  • Received : 2009.07.23
  • Accepted : 2010.06.17
  • Published : 2011.04.25

Abstract

In flexural strength design of unconfined reinforced concrete (RC) members, the concrete compressive stress-strain curve is scaled down from the uni-axial stress-strain curve such that the maximum concrete stress adopted in design is less than the uni-axial strength to account for the strain gradient effect. It has been found that the use of this smaller maximum concrete stress will underestimate the flexural strength of unconfined RC members although the safety factors for materials are taken as unity. Herein, in order to investigate the effect of strain gradient on the maximum concrete stress that can be developed in unconfined flexural RC members, several pairs of plain concrete (PC) and RC inverted T-shaped specimens were fabricated and tested under concentric and eccentric loads. From the test results, the maximum concrete stress developed in the eccentric specimens under strain gradient is determined by the modified concrete stress-strain curve obtained from the counterpart concentric specimens based on axial load and moment equilibriums. Based on that, a pair of equivalent rectangular concrete stress block parameters for the purpose of flexural strength design of unconfined RC members is determined.

Keywords

References

  1. ACI Committee 318 (2008), Building code requirements for reinforced concrete and commentary, ACI 318M-08, Manual of Concrete Practice, American Concrete Institute, Michigan, USA, 465.
  2. Ashour, S.A. (2000), "Effect of compressive strength and tensile reinforcement ratio on flexural behaviour of high-strength concrete beams", Eng. Struct., 25(8), 1083-1096.
  3. Attard, M.M. and Stewart, M.G. (1998), "A two parameter stress block for high-strength concrete", ACI Struct. J., 95(3), 305-317.
  4. Au, F.T.K. and Kwan, A.K.H. (2004), "A minimum ductility design method for non-rectangular high-strength concrete beams", Comput. Concrete, 1(2), 115-130. https://doi.org/10.12989/cac.2004.1.2.115
  5. Au, F.T.K., Bai, Z.Z. and Kwan, A.K.H. (2005), "Complete moment-curvature relationship of reinforced normal- and high-strength concrete beams experiencing complex load histroy", Comput. Concrete, 2(4), 309-324. https://doi.org/10.12989/cac.2005.2.4.309
  6. Au, F.T.K and Bai, Z.Z. (2006), "Effect of axial load on flexural behaviour of cyclically loaded RC columns", Comput. Concrete, 3(4), 261-284. https://doi.org/10.12989/cac.2006.3.4.261
  7. Bae, S. and Bayrak, O. (2003), "Stress block parameters for high-strength concrete members", ACI Struct. J., 100(5), 626-636.
  8. Bechtoula, H., Kono, S. and Watanabe, F. (2009), "Seismic performance of high strength reinforced concrete columns", Struct. Eng. Mech., 31(6), 697-716. https://doi.org/10.1016/j.engstruct.2008.11.006
  9. Debernardi, P.G. and Taliano, M. (2002), "On evaluation of rotation capacity for reinforced concrete beams", ACI Struct. J., 99(3), 360-368.
  10. Esmaeily, A. and Peterman, R.J. (2007), "Performance analysis tool for reinforced concrete members", Comput. Concrete, 4(5), 331-346. https://doi.org/10.12989/cac.2007.4.5.331
  11. European Committee for Standardization (2004), Eurocode 2: Design of concrete structures: Part 1-1: General rules and rules for buildings, UK, 225.
  12. Hognestad, E., Hanson, N.W. and McHenry, D. (1955), "Concrete stress distribution in ultimate strength design", ACI J. Proc., 52, 455-479.
  13. Ibrahim, H.H.H. and MacGregor, J.G. (1996), "Flexural behavior of laterally reinforced high-strength concrete sections", ACI Struct. J., 93(6), 674-684.
  14. Ibrahim, H.H.H. and MacGregor, J.G. (1997), "Modification of the ACI rectangular stress block for high-strength concrete", ACI Struct. J., 94(1), 40-48.
  15. Kaar, P.H., Hanson, N.W. and Capell, H.T. (1978), "Stress-strain characteristics of high strength concrete", ACI Special Publication, Douglas McHenry International Symposium on Concrete and Concrete Structures, ACI, Detroit, pp. 161-185.
  16. Kim, J.H. (2005), "Ductility enhancement of reinforced concrete thin wall", Comput. Concrete, 2(2), 111-123. https://doi.org/10.12989/cac.2005.2.2.111
  17. Kim, S.P. (2007), "Nonlinear analysis of RC beams based on simplified moment-curvature relation considering fixed-end rotation", Comput. Concrete, 4(6), 457-475. https://doi.org/10.12989/cac.2007.4.6.457
  18. Kumar, P. (2006), "Effect of strain ratio variation on equivalent stress block parameters for normal weight high strength concrete", Comput. Concrete, 3(1), 17-28. https://doi.org/10.12989/cac.2006.3.1.017
  19. Lam, S.S.E., Wu, B., Wong, Y.L., Wang, Z.Y., Liu, Z.Q. and Li, C.S. (2003), "Drift capacity of rectangular reinforced concrete columns with low lateral confinement and high-axial load", J. Struct. Eng. - ASCE, 129(6), 733-742. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:6(733)
  20. Lam, S.S.E., Wu, B., Liu, Z.Q. and Wong, Y.L. (2008), "Experimental study on seismic performance of coupling beams not designed for ductility", Struct. Eng. Mech., 28(3), 317-333. https://doi.org/10.12989/sem.2008.28.3.317
  21. Lin, H.J., Liao, C.I. and Yang, C. (2006), "A numerical analysis of compressive strength of rectangular concrete columns confined by FRP", Comput. Concrete, 3(4), 235-248. https://doi.org/10.12989/cac.2006.3.4.235
  22. Lam, J.Y.K., Ho, J.C.M. and Kwan, A.K.H. (2009), "Maximum axial load level and minimum confinement for limited ductility design of concrete columns", Comput. Concrete, 6(5), 357-376. https://doi.org/10.12989/cac.2009.6.5.357
  23. Lu, X. and Zhou, Y. (2007), "An applied model for steel reinforced concrete columns", Struct. Eng. Mech., 27(6), 697-711. https://doi.org/10.12989/sem.2007.27.6.697
  24. Maghsoudi, A.A. and Bengar, H.A. (2006), "Flexural ductility of HSC members", Struct. Eng. Mech., 24(2), 195-212. https://doi.org/10.12989/sem.2006.24.2.195
  25. Mansur, M.A., Chin M.S. and Wee, T.H. (1997), "Flexural behavior of high-strength concrete beams", ACI Struct. J., 94(6), 663-673.
  26. Marefat, M.S., Khanmohammadi, M., Bahrani, M.K. and Goli, A. (2005), "Cyclic load testing and numerical modelling of concrete columns with substandard seismic details", Comput. Concrete, 2(5), 367-380. https://doi.org/10.12989/cac.2005.2.5.367
  27. Marefat, M.S., Khanmohammadi, M., Bahrani, M.K. and Goli, A. (2006), "Experimental assessment of reinforced concrete columns with deficient seismic details under cyclic load", Adv. Struct. Eng., 9(3), 337-347. https://doi.org/10.1260/136943306777641959
  28. Mertol, H.C., Rizkalla, S., Zia, P. and Mirmiran, A. (2008), "Characteristics of compressive stress distribution in high-strength concrete", ACI Struct. J., 105(5), 626-633.
  29. Mo, Y.L. and Wang, S.J. (2000), "Seismic behavior of RC columns with various tie configurations", J. Struct. Eng. - ASCE, 126(10), 1122-1130. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:10(1122)
  30. Narayan, K.S.B. and Venkataramana, K. (2007), "Shape optimization of steel reinforced concrete beams", Comput. Concrete, 4(4), 317-330. https://doi.org/10.12989/cac.2007.4.4.317
  31. Ozbakkaloglu, T. and Saatcioglu, M. (2004), "Rectangular stress block for high-strength concrete", ACI Struct. J., 101(4), 475-483.
  32. Pam, H.J. and Ho, J.C.M. (2001), "Flexural strength enhancement of confined reinforced concrete columns", Proc. Institut. Civil Eng. Struct. Build., 146(4), 363-370. https://doi.org/10.1680/stbu.2001.146.4.363
  33. Pam, H.J., Kwan, A.K.H. and Ho, J.C.M. (2001), "Post-peak behavior and flexural ductility of doubly reinforced normal- and high-strength concrete beams", Struct. Eng. Mech., 12(5), 459-474. https://doi.org/10.12989/sem.2001.12.5.459
  34. Park, R. and Paulay, T. (1975), Reinforced concrete structures, John Wiley & Sons, New York, U.S.A., 769.
  35. Pecce, M. and Fabbrocino, G. (1999), "Plastic rotation capacity of beams in normal and high-performance concrete", ACI Struct. J., 96(2), 290-296.
  36. Rashid, M.A. and Mansur, M.A. (2005), "Reinforced high-strength concrete beams in flexure", ACI Struct. J., 102(3), 462-471.
  37. Sheikh, S.A. and Khoury, S.S. (1993), "Confined concrete columns with stubs", ACI Struct. J., 90(4), 414-431.
  38. Sheikh, S.A. and Uzumeri, S.M. (1980), "Strength and ductility of tied concrete columns", J. Struct. Eng. Div., 106, 1079-1101.
  39. Soliman, M.T.M. and Yu, C.W. (1967), "The flexural stress-strain relationship of concrete confined by rectangular transverse reinforcement", Mag. Concrete Res., 19(61), 223-238. https://doi.org/10.1680/macr.1967.19.61.223
  40. Standard Australia (2001), Australian standard concrete structures AS 3600-2001, Australia, 175.
  41. Standards New Zealand, NZS 3101 (2005), Concrete structures standard, Part 1 - The design of concrete structures, Wellington, New Zealand.
  42. Swartz, S.E., Nikaeen, A., Narayan, B.H.D., Periyakaruppan, N. and Refai, T.M.E. (1985), "Structural bending properties of high strength concrete", ACI Spec. Public., 87(09), 147-178.
  43. Tan, T.H. and Nguyen, N.B. (2004), "Determination of stress-strain curves of concrete from flexure tests", Mag. Concrete Res., 56(4), 243-250. https://doi.org/10.1680/macr.2004.56.4.243
  44. Tan, T.H. and Nguyen, N.B. (2005), "Flexural behavior of confined high-strength concrete columns", ACI Struct. J., 102(2), 198-205.
  45. Tabsh, S.W. (2006), "Elimination of the effect of strain gradient from concrete compressive strength test results", Comput. Concrete, 3(6), 375-388. https://doi.org/10.12989/cac.2006.3.6.375
  46. Wang, X.H. and Liu, X.L. (2009), "Predicting the flexural capacity of RC beam with partially unbonded steel reinforcement", Comput. Concrete, 6(3), 235-252. https://doi.org/10.12989/cac.2009.6.3.235
  47. Watson, S. and Park, R. (1994), "Simulated seismic load tests on reinforced concrete columns", J. Struct. Eng. - ASCE, 120(6), 1825-1849. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:6(1825)
  48. Wu, Y.F., Oehlers, D.J. and Griffith, M.C. (2004), "Rational definition of the flexural deformation capacity of RC column sections", Eng. Struct., 26, 641-650. https://doi.org/10.1016/j.engstruct.2004.01.001

Cited by

  1. Improving design limits of strength and ductility of NSC beam by considering strain gradient effect vol.47, pp.2, 2013, https://doi.org/10.12989/sem.2013.47.2.185
  2. Combined strain gradient and concrete strength effects on flexural strength and ductility design of RC columns vol.15, pp.4, 2015, https://doi.org/10.12989/cac.2015.15.4.607
  3. Automated design of optimum longitudinal reinforcement for flexural and axial loading vol.10, pp.2, 2012, https://doi.org/10.12989/cac.2012.10.2.149
  4. Concurrent flexural strength and ductility design of RC beams via strain-gradient-dependent concrete stress-strain curve vol.24, pp.9, 2015, https://doi.org/10.1002/tal.1203