A study on the machinability of Carbon Fiber Reinforced Plastics on tool shape

공구형상에 따른 CFRP(Carbon Fiber Reinforced Plastics) 복합재료의 절삭 특성에 관한 연구

  • Received : 2011.05.17
  • Accepted : 2011.08.10
  • Published : 2011.12.15

Abstract

CFRP(Carbon Fiber Reinforced Plastics) has been used many industries aerospace, automobile, medical device and building material industries, etc. Because it is lighter than other metals and has good properties, such as rigidity, strength and wear. CFRP may be cured integrity. However, it needs postprocessing similar to drilling or endmilling for shape cutting and combination of various material. In this paper, tool dynamometer and accelerometer used to signal analysis for machining properties under various cutting conditions and tool shape changes. In addition, microscope used to verify the machined CFRP surface. As the results, it was found that the cutting force and the vibration were decreased in the increasing of cutting edge (2-flute < 4-flute < composite tool), and the good machined surface can be obtained in this experiments.

Keywords

References

  1. Abrate, S., and Walton, D., 1992, "Machining of composite materials. Part I : Traditional methods," Composites Manufacturing, Vol. 3, No. 2, pp. 75-83. https://doi.org/10.1016/0956-7143(92)90119-F
  2. Rahman, M., Ramakrishna, S., Prakash, J. R. S., and Tan, D. C. G., 1999, "Machinability Study of Carbon Fiber Reinforced Composite," J. Mat. Proc. Tech., Vol. 89-90, pp. 292-297. https://doi.org/10.1016/S0924-0136(99)00040-0
  3. Teti, R., 2002, "Machining of Composite Materials," CIRP Annals-Manu. Tech., Vol. 51, Issue 2, pp. 611-634. https://doi.org/10.1016/S0007-8506(07)61703-X
  4. Paule Davim, J., and Pedro Reis., 2005, "Damage and Dimensional Precision on Milling Carbon Fiber-reinforced Plastics using Design Experiments," J. Mat. Proc. Tech., Vol. 160, Issue 2, pp. 160-167. https://doi.org/10.1016/j.jmatprotec.2004.06.003
  5. Sung, I. S., Lim, S. H., and Kim, J. H., 2005, "A Study on the Chip Shapes Properties of the Fiber Reinforced Plastics by High Speed Drilling Process," J. of the KSMTE., Vol 2005, pp. 168-173.
  6. Pwa, H. Y., and Hocheng, H., 1998, "Chip Formation Model of Cutting Fiber Reinforced Plastic Perpendicular to Fiber Axis," Trans. of the ASME, Vol. 120, pp. 192-196.
  7. Wang, D. H., Ramulu, M., and Arola, D., 1995, "Orthogonal Cutting Mechanisms of Graphite/Epoxy Composite. Part I : Multi-Directional Laminate," Int. J. of Mach. Tools and Manu., Vol. 35, No. 12, pp. 1623-1638. https://doi.org/10.1016/0890-6955(95)00014-O
  8. Wang, D. H., Ramulu, M., and Arola D., 1995, "Orthogonal Cutting Mechanisms of Graphite/Epoxy Composite. Part II : Multi-Directional Laminate," Int. J. of Mach. Tools and Manu., Vol. 35, No. 12, pp. 1639-1648. https://doi.org/10.1016/0890-6955(95)00015-P
  9. Davim, J. P., and Reis, P., 2003, "Study of Delamination in Drilling Carbon Fiber-reinforced Plastics (CFRP) using Design Experiments," Composite Structures, No. 59, Issue 4, pp. 481-487. https://doi.org/10.1016/S0263-8223(02)00257-X