DOI QR코드

DOI QR Code

Investigation into shear properties of medium strength reinforced concrete beams

  • Shah, Attaullah (Project Directorate, Allama Iqbal Open University Islamabad-Pakistan) ;
  • Ahmad, Saeed (Department of Civil Engineering, University of Engineering and Technology) ;
  • Khan, Salimullah (Department of Pharmacy, Hazara University Mansehra)
  • 투고 : 2007.02.08
  • 심사 : 2009.10.22
  • 발행 : 2010.06.20

초록

The shear contribution of transverse steel in reinforced concrete beams is generally assumed as independent of the concrete strength by most of the building codes. The shear strength of RC beams with web reinforcement is worked out by adding the individual contributions of concrete and stirrups. In this research 70 beams of medium strength concrete in the range of 52-54 MPa, compressive strength were tested in two sets of 35 beams each. In one set of 35 beams no web reinforcement was used, whereas in second set of 35 beams web reinforcement was used to check the contribution of stirrups. The values have also been compared with the provisions of ACI, Eurocode and Japanese Code building codes. The results of two sets of beams, when compared mutually and provisions of the building codes, showed that the shear strength of beams has been increased with the addition of stirrups for all the beams, but the increase is non uniform and irregular. The comparison of observed values with the provisions of selected codes has shown that EC-02 is relatively less conservative for low values of longitudinal steel, whereas ACI-318 overestimates the shear strength of RC beams at higher values of longitudinal steel. The Japanese code of JSCE has given relatively good results for the beams studied.

키워드

참고문헌

  1. Arsalan, G. (2007), "Shear strength of reinforced concrete beams with stirrups", Mater. Struct., 41(1), 113-122. https://doi.org/10.1617/s11527-007-9223-3
  2. Arsalan, G. (2008), "Cracking shear strength of RC slender beams without stirrups", J. Civil Eng. Manage., 14(3), 177-182. https://doi.org/10.3846/1392-3730.2008.14.14
  3. ASCE-ACI Committee 445 (1998), "Recent approaches to shear design of structural concrete", J. Struct. Eng., 124(12), 1375-1417. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:12(1375)
  4. Cladera, A. and Mari, A.R. (2004), "Shear design procedure for reinforced normal and high strength concrete beams using artificial neural network-part II. Beams with stirrups", Eng. Struct., 26(7), 927-936. https://doi.org/10.1016/j.engstruct.2004.02.011
  5. Cladera, A. and Mari, A.R. (2005), "Experimental study on high strength concrete beams failing in shear", Eng. Struct., 27(10), 1519-1527. https://doi.org/10.1016/j.engstruct.2005.04.010
  6. Eurocode No. 2 (1991), Design of Concrete Structures. Part 1: General Rules and Rules for Buildings, Commission of the European Communities, ENV 1992-1-1 (Final draft 2002).
  7. Japan Society of Civil Engineers (1986), Specification for Design and Construction of Concrete Structures: Design, JSCE Standard, Part 1, Japan Society of Civil Engineers, Tokyo.
  8. Kani, G.N.J. (1964), "The riddle of shear failure and its solution", J. Proceed., 61(4), 441-4
  9. Kani, G.N.J. (1966), "Basic facts concerning the shear failure", J. Proceed., 63(6), 185-197.
  10. Kani, G.N.J. (1969), "A rational theory for the function of web reinforcement", J. Proceed., 66(3), 185-197.
  11. Kostovos, M.D. (1983), "Mechanics of shear failure", Mag. Concrete Res., 35(123), 99-106. https://doi.org/10.1680/macr.1983.35.123.99
  12. Kostovos, M.D. (1986), "Behaviour of beams with shear span to depth ratio greater than 2.5", J. Proceed., 83(6), 1026-1034.
  13. Londhe, R.S. (2009), "The design of reinforced concrete beams for shear in current practice: A new analytical model", Struct. Eng. Mech., 31(2), 225-235. https://doi.org/10.12989/sem.2009.31.2.225
  14. National Cooperative Highway Research Program (NCHRP) (2005), Transport Research Board Washington DCUSA-2005.
  15. Ritter, W. (1899), "Die bauweise hennebique", Shweizerische Bauzeitung, 33(7), 59-61.
  16. Russo, G., Somma, G. and Angeli, P. (2004), "Deign shear strength formula for High Strength concrete beams", Mater. Struct., 10(37), 1519-1527.
  17. Sarkar, S., Adwan, O. and Bose, B. (1999), "Shear stress contribution and failure mechanisms of high strength concrete beams", Mater. Struct., 32(2), 112-116. https://doi.org/10.1007/BF02479437
  18. Shehata, I., Shehata, L. and Garcia, S. (2003), "Minimum Steel ratios in reinforced concrete beams made of concrete with different strengths-Theoretical approach", Mater. Struct., 36(1), 3-11. https://doi.org/10.1007/BF02481565
  19. Tompos, E.J. and Frosch, R.J. (2002), "Influence of beam size, longitudinal reinforcement, and stirrup effectiveness on concrete shear strength", ACI Struct. J., 99(5), 559-567.
  20. Vecchio, F.J. and Collins, M.P. (1986), "The modified compression field theory for reinforced concrete elements subjected to shear", ACI Struct. J., 83(2), 219-231.
  21. Zararis, P.D. (2003), "Shear strength and minimum shear reinforcement of reinforced concrete slender beams", ACI Struct. J., 100(2), 203-214.