Journal of Ocean Engineering and Technology (한국해양공학회지)

Korean Society of Ocean Engineers (한국해양공학회)
권호 표지

On the Effect of Plate Curvature on Welding Deformation

용접변형에의 곡률의 영향에 관한 연구

  • Lee, Joo-Sung (School of Naval Architecture and Ocean Engineering, University of Ulsan) ;
  • Lee, Jin-Tae (School of Naval Architecture and Ocean Engineering, University of Ulsan)
  • 이주성 (울산대학교 조선해양공학부) ;
  • 이진태 (울산대학교 조선해양공학부)
  • Received : 2009.10.29
  • Accepted : 2010.04.23
  • Published : 2010.04.30
Download PDF
⟨ Previous Next ⟩

Abstract

A simplified finite element analysis has been used to predict the weld-induced deformation to bead-on-plate welding of steel plates having curvatures in the welding direction. In this study, the equivalent loading method based on inherent strain was used to investigate the effect of longitudinal curvature on the weld-induced deformation of curved plates. Equivalent loads were derived from the inherent strain distribution around the weld line, and the loads were used for linear finite element analyses. These kinds of numerical simulations can, of course, be performed by using the rigorous thermalelastic-plastic analysis method. This approach is not, however, practical for use in weld-induced deformation analysis of large and complex structures, such as ship structures, in view of computing time and cost. The present equivalent load approach has been applied to several plate models having curvatures in the welding direction, and the results are compared with those obtained by thermal-elastic-plastic analysis and also with those obtained by the other simplified method found in reference. As far as the present results are concerned, the weld-induced deformation of curved plates can be accurately predicted by the method presented in this paper.

Keywords

References

  1. 용접강도연구회 (2005). “유한요소해석을 이용한 Arc 용접부의 온도분포 예측 표준화”, 대한용접․접합학회지, 제23권, 제6호, pp 497-503
  2. 이상훈, 안윤남, 이주성 (2009). “선상가열에 의한 변형에 곡률 의 영향에 관한 연구”, 2009년도 한국해양공학회 추계학술 대회 논문집, pp 188-191.
  3. Goldak, J., Chakravarti, A. and Bibby, M. (1984). “A New Finite Element Model for Welding Heat Sources”, Metallurgical Transactions B, Vol 15B, pp 299-305.
  4. Jang, C.D., Ha, Y.S., Ko, D.E. and Moon, S.C. (2002).”Determination of Inherent Strain Regions to EstimatePlate Deformation by Line Heating”, J. of the Society ofNaval Architects of Korea, Vol 39, No 1, pp 82-89. https://doi.org/10.3744/SNAK.2002.39.1.082
  5. Jang, C.D. and Lee, C.H. (2000). ”A Study on the Prediction and Control of Welding Deformation of Ship Hull Blocks ”,J. of the Society of Naval Architects of Korea, Vol 37, No2, pp 127-136.
  6. Lee, C.H. (2002). Prediction of Welding Deformation of Ship Hull Panel Blocks using Equivalent Loading Method Based on Inherent Strain, PhD thesis, Seoul National Univ.
  7. Luo, Y., Ishayama, M. and Murakawa, H. (1999). ”Study on Welding Deformation of Plate with Longitudinal Curvature”,Yosetsu Kozo Shinpojiumu Koen Ronbunshu, Vol 1999, pp. 311-317.