DOI QR코드

DOI QR Code

Finite element model updating of an arch type steel laboratory bridge model using semi-rigid connection

  • Altunisik, Ahmet Can (Karadeniz Technical University, Department of Civil Engineering) ;
  • Bayraktar, Alemdar (Karadeniz Technical University, Department of Civil Engineering) ;
  • Sevim, Baris (Karadeniz Technical University, Department of Civil Engineering) ;
  • Kartal, Murat Emre (Zonguldak Karaelmas University, Department of Civil Engineering) ;
  • Adanur, Suleyman (Karadeniz Technical University, Department of Civil Engineering)
  • 투고 : 2010.05.04
  • 심사 : 2010.11.03
  • 발행 : 2010.11.25

초록

This paper presents finite element analyses, experimental measurements and finite element model updating of an arch type steel laboratory bridge model using semi-rigid connections. The laboratory bridge model is a single span and fixed base structure with a length of 6.1 m and width of 1.1m. The height of the bridge column is 0.85 m and the maximum arch height is 0.95 m. Firstly, a finite element model of the bridge is created in SAP2000 program and analytical dynamic characteristics such as natural frequencies and mode shapes are determined. Then, experimental measurements using ambient vibration tests are performed and dynamic characteristics (natural frequencies, mode shapes and damping ratios) are obtained. Ambient vibration tests are performed under natural excitations such as wind and small impact effects. The Enhanced Frequency Domain Decomposition method in the frequency domain and the Stochastic Subspace Identification method in the time domain are used to extract the dynamic characteristics. Then the finite element model of the bridge is updated using linear elastic rotational springs in the supports and structural element connections to minimize the differences between analytically and experimentally estimated dynamic characteristics. At the end of the study, maximum differences in the natural frequencies are reduced on average from 47% to 2.6%. It is seen that there is a good agreement between analytical and experimental results after finite element model updating. Also, connection percentages of the all structural elements to joints are determined depending on the rotational spring stiffness.

키워드

참고문헌

  1. Altunisik, A.C., Bayraktar, A. and Sevim, B. (2010). "Output-only system identification of post tensioned segmental concrete highway bridges", J. Bridge. Eng., DOI: 10.1061/(ASCE)BE.1943-5592.0000150.
  2. Bayraktar, A., Altunisik, A.C., Sevim, B. and Turker, T. (2007), "Modal testing and finite element model calibration of an arch type steel footbridge", Steel. Compos. Struct., 7(6), 487-502. https://doi.org/10.12989/scs.2007.7.6.487
  3. Bendat, J.S. and Piersol, A.G. (2004), Random data: analysis and measurement procedures, John Wiley and Sons, USA.
  4. Bilello, C., Bergman, L.A. and Kuchma, D. (2004), "Experimental investigation of a small-scale bridge model under a moving mass", J. Struct. Eng-ASCE, 130, 799-804. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:5(799)
  5. Brincker, R. Zhang, L. and Andersen, P. (2000), "Modal identification from ambient responses using frequency domain decomposition", 18th International Modal Analysis Conference, San Antonio, USA.
  6. Chen, W.F. and Lui, E.M. (1991), Stability design of steel frames, CRC Press Inc.
  7. Felber, A.J. (1993), Development of hybrid bridge evaluation system, Ph.D thesis, University of British Columbia, Vancouver, Canada, 1993.
  8. Filho, M.S., Guimarães, M.J.R., Sahlit, C.L. and Brito, J.L.V. (2004), "Wind pressures in framed structures with semi-rigid connections", J. Braz. Soc. Mech. Sci. Eng., 26, 180-189.
  9. Juang, J.N. (1994), Applied system identification, Englewood Cliffs (NJ): Prentice-Hall Inc.
  10. Juang, J.N. and Phan, M.Q. (2001), Identification and control of mechanical systems, Cambridge University Press, Cambridge, U.K.
  11. Kartal, M.E. (2004), The effect of partial fixity at nodal points on the behavior of the truss and prefabricated structures, MS Thesis, Zonguldak Karaelmas University.
  12. Kohoutek, R. (2000), "Non-destructive and ultimate testing of semi-rigid connections", Fourth International Workshop on Connections in Steel Structures, Roanoke, VA, October.
  13. Lu, P., Zhao, R. and Zhang, J. (2010), "Experimental and finite element studies of special-shape arch bridge for self-balance", Struct. Eng. Mech., 35(1), 37-52. https://doi.org/10.12989/sem.2010.35.1.037
  14. McGuire, W., Gallagher, R.H. and Ziemian, R.D. (1999), Matrix Structural Analysis, 2nd ed., John Wiley & Sons, Inc., USA.
  15. Modak, S.V., Kundra, T.K. and Nakra, B.C. (2002), "Comparative study of model updating methods using experimental data", Compos. Struct., 80, 437-447. https://doi.org/10.1016/S0045-7949(02)00017-2
  16. Monforton, G.R. and Wu, T.S. (1963), "Matrix analysis of semi-rigidly connected frames", J. Struct. Div-ASCE, 89, 13-42.
  17. OMA (2006), Operational modal analysis, Release 4.0. Structural Vibration Solutions A/S, Denmark.
  18. Peeters, B. (2000), System identification and damage detection in civil engineering, Ph.D Thesis, K.U, Leuven, Belgium.
  19. PULSE (2006), Analyzers and solutions, Release 11.2. Bruel and Kjaer, Sound and Vibration Measurement A/S, Denmark.
  20. Rainieri, C., Fabbrocino, G., Cosenza, E. and Manfredi, G. (2007), "Implementation of OMA procedures using labview: theory and application", 2nd International Operational Modal Analysis Conference, Copenhagen, Denmark, May.
  21. Ren, W.X., Zhao, T. and Harik, I.E. (2004), "Experimental and analytical modal analysis of steel arch bridge", J. Struct. Eng-ASCE, 130, 1022-1031. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:7(1022)
  22. Sanayei, M. and DiCarlo, C. (2009), "Finite element model updating of scale bridge model using measured modal response data", Structures Congress, Austin, Texas.
  23. SAP2000 (1998), Integrated finite element analysis and design of structures, Computers and Structures Inc, Berkeley, California, USA.
  24. Sekulovic, M. Salatic, R. and Nefovska, M. (2002), "Dynamic analysis of steel frames with flexible connections", Compos. Struct., 80, 935-955. https://doi.org/10.1016/S0045-7949(02)00058-5
  25. Sevim, B., Bayraktar, A. and Altunisik, A.C. (2010). "Finite element model calibration of berke arch dam using operational modal testing", J. Vib. Control., DOI: 10.1177/1077546310377912.
  26. VanOverschee, P. and DeMoor, B. (1996), Subspace identification for linear systems: theory-implementationapplications, Kluwer Academic Publishers, Dordrecht, NL.
  27. Wang, Y.F., Han, B., Du, J.S. and Liu, K.W. (2007), "Creep analysis of concrete filled steel tube arch bridges", Struct. Eng. Mech., 27(6), 639-650. https://doi.org/10.12989/sem.2007.27.6.639
  28. Yang, C. (2007), Seismic analysis of long span bridges including the effects of spatial variation of seismic waves on bridges, Ph.D Thesis, University of Hong Kong.
  29. Yu, D.J. and Ren, W.X. (2005), "EMD-based stochastic subspace identification of structures from operational vibration measurements", Eng. Struct., 27, 1741-1751. https://doi.org/10.1016/j.engstruct.2005.04.016
  30. Zapico, J.L., Gonzalez, M.P., Friswell, M.I., Taylor, A.J. and Crewe, A.J. (2003), "Finite element model updating of a small scale bridge", J. Sound. Vib., 268, 993-1012. https://doi.org/10.1016/S0022-460X(03)00409-7
  31. Zhu, S. and Cheng, X. (2008), "Test and analyses of a new double-arch steel gate under cyclic loading", J. Constr. Steel. Res., 64, 454-464. https://doi.org/10.1016/j.jcsr.2007.10.004
  32. Zivanovic, S., Pavic, A. and Reynolds, P. (2007), "Finite element modelling and updating of a lively footbridge: the complete process", J. Sound. Vib., 301, 126-145. https://doi.org/10.1016/j.jsv.2006.09.024

피인용 문헌

  1. Arch-to-beam rigidity analysis for V-shaped rigid frame composite arch bridges vol.19, pp.2, 2015, https://doi.org/10.12989/scs.2015.19.2.405
  2. Stability condition for the evaluation of damage in three-point bending of a laminated composite vol.15, pp.2, 2013, https://doi.org/10.12989/scs.2013.15.2.203
  3. Investigation of a historic masonry structure by numerical and operational modal analyses vol.24, pp.13, 2015, https://doi.org/10.1002/tal.1213
  4. Spatial mechanical behaviors of long-span V-shape rigid frame composite arch bridges vol.47, pp.1, 2013, https://doi.org/10.12989/sem.2013.47.1.059
  5. Application of OMA on the bench-scale earthquake simulator using micro tremor data vol.61, pp.2, 2017, https://doi.org/10.12989/sem.2017.61.2.267
  6. OMA of model steel structure retrofitted with CFRP using earthquake simulator vol.12, pp.6, 2017, https://doi.org/10.12989/eas.2017.12.6.689
  7. GFRP retrofitting effect on the dynamic characteristics of model steel structure vol.28, pp.2, 2010, https://doi.org/10.12989/scs.2018.28.2.223
  8. Behavior of a steel bridge with large caisson foundations under earthquake and tsunami actions vol.31, pp.6, 2010, https://doi.org/10.12989/scs.2019.31.6.575
  9. Dynamic analysis of the train-bridge system considering the non-linear behaviour of the track-deck interface vol.220, pp.None, 2020, https://doi.org/10.1016/j.engstruct.2020.110980