Journal of Ocean Engineering and Technology (한국해양공학회지)

Korean Society of Ocean Engineers (한국해양공학회)
권호 표지

An Impact Analysis of Adhesively-Bonded Single Lap Joint

단면 겹치기 접착 조인트의 충돌해석

  • Lee, Ju-Won (Department of Ocean Engineering, Pukyong National University) ;
  • Na, Won-Bae (Department of Ocean Engineering, Pukyong National University)
  • Published : 2010.02.28
Download PDF
⟨ Previous Next ⟩

Abstract

This study presents an explicit dynamic analysis of an adhesively bonded single-lap joint under an impact load. The finite element software, ANSYS LS-DYNA, was used for the analysis and Von Mises stresses were obtained from the analysis. To model the adherents, solid elements were used and a rigid body was assumed for impactor modeling. Three impact heights (1 m, 5 m, and 10 m) were applied to consider different impact conditions and infinite boundary conditions were applied to the end-area of each adherent to save computational time in the analysis. In addition to investigating the stresses in the normal state, we also investigated the stresses in a damaged state (elasticity deterioration), simulated by a change in Young's modulus for 36 of the 3600 elements in the upper layer of the adhesive. The results showed that the location of damage is critical to the stress state of each layer (upper, middle, and lower).

Keywords

References

  1. 김현중, 김대준 (2001). "에폭시수지 접착제의 특성과 응용", 접착 및 계면, 기술강좌(3), 제2권, 제2호, pp 35-47.
  2. 박성완, 이장규 (2004). "접착이음의 강도평가에 대한 해석", 한국공작기계학회 2004 추계학술대회 논문집, pp 98-107.
  3. 안석환, 김진욱, 도재윤, 김현수, 남기우 (2005). "저속충격에 의한 복합재료 적층판의 손상", 한국해양공학회지, 제19권, 제1호, pp 39-43.
  4. 유종선, 이승희 (2000). "접착과 접착 메커니즘", 접착 및 계면, 기술강좌(1), 제1권, 제1호, pp 63-72.
  5. 오승규, 장철섭, 한준영, 이원 (2004). "초음파신호해석을 이용한 단순겹치기 접착이음의 강도평가", 대한기계학회지, 제22권, 제5호, pp 32-37.
  6. 이영상, 하진국, 이의수 (2008). "실험계획법을 이용한 아크릴 점착제의 점착력 최적화", 접착 및 계면 학회지, 제9권, 제1호, pp 22-27.
  7. 이원, 정의섭, 유영철 (1995). "피착체의 두께가 다른 단순겹치기 접착이음에 대한 응력특이성 파라미터의 해석", 한국자동차공학회 1995년 춘계학술대회 논문집, pp 16-22.
  8. Andruet, R.H., Dillard, D.A. and Holzer, S.M. (2001). "Twoand Three-dimensional Geometrical Nonlinear Finite Elements for Analysis of Adhesive Joints", International Journal of Adhesion & Adhesives, Vol 21, pp 17-34. https://doi.org/10.1016/S0143-7496(00)00024-5
  9. Avila, A.F. and Bueno, P.D.O. (2004). "Stress Analysis on a Wavy-lap Bonded Joint for Composites", International Journal of Adhesion & Adhesives, Vol 24, pp 407-414. https://doi.org/10.1016/j.ijadhadh.2003.12.001
  10. Carpenter, W.C. and Barsoum, R. (1989). "Two Finite Elements for Modeling the Adhesive in Bonded Configuration", Journal of Adhesives, Vol 30, pp 25-46. https://doi.org/10.1080/00218468908048192
  11. Goncalves, J.P.M., de Moura, M.F.S.F. and de Castro, P.M.S.T. (2002). "A Three-Dimensional Finite Element Models for Stress Analysis of Adhesive Joints", International Journal of Adhesion & Adhesives, Vol 22, pp 357-365. https://doi.org/10.1016/S0143-7496(02)00015-5
  12. Hellmanns, M., Bohm, S. and Dilger, K. (2006). "Manual Application of Adhesives", Journal of Adhesion and Interface, Vol 7, No 4, pp 24-27.
  13. Li, G. and Lee-Sullivan, P. (2001). "Finite Element and Experimental Studies on Single-Lap Balanced Joints in Tension", International Journal of Adhesion & Adhesives, Vol 21, pp 211-220. https://doi.org/10.1016/S0143-7496(00)00052-X
  14. Lucas, F.M. da Silva, Ramos, J.E., Figuiredo, M.V. and Strohaecker, T.R. (2006). "Influence of the Adhesive, the Adherend and the Overlap on the Single Lap Shear Strength", Journal of Adhesion and Interface, Vol 7, No 4, pp 1-9.
  15. Richardson, G., Crocombe, A.D. and Smith, P.A. (1993). "A Comparison of Two and Three-dimensional Finite Element Analysis of Adhesive Joints", International Journal of Adhesion & Adhesives, Vol 13, pp 193-200. https://doi.org/10.1016/0143-7496(93)90042-8
  16. Symietz, D. and Lutz, A. (2006). "High-performing Adhesive Bonding Fastening Technique For Automotive Body Structures", Journal of Adhesion and Interface, Vol 7, No 4, pp 60-64.
  17. Wooley, G.R. and Carver, D.R. (1971). "Stress Concentration Factors for Bonded Lap Joint", Journal of Aircraft, Vol 8, pp 817-820. https://doi.org/10.2514/3.44305