DOI QR코드

DOI QR Code

Network-Based Overhead Crane Control System Using Matrix Converters

매트릭스 컨버터를 사용한 네트워크 기반 천정형 크레인 제어 시스템

  • 이홍희 (울산대 전기전자정보시스템공학부) ;
  • 전태원 (울산대 전기전자정보시스템공학부)
  • Published : 2010.02.20

Abstract

This paper presents supervisor control methods at a matrix converter controlled overhead crane system based on a controller area network (CAN). Four induction motors are used to drive the gantry, trolley, and hoist at he crane and each motor is controlled by the matrix converter with direct torque control (DTC). Both the position control algorithm and the supervisor control system using CAN are introduced. Simulation and experimental results are carried out to verify the performance of position control at the matrix converter controlled crane system.

본 논문은 CAN을 사용하여 매트릭스 컨버터로 구동되는 천정형 크레인의 총괄제어 기법을 제시하였다. 크레인의 갠추리, 트롤리 및 호이스트 구동용으로 4개 매트릭스 컨버터-유도전동기 구동장치를 직접토크 기법으로 위치 제어한다. 위치제어 알고리즘과 CAN을 사용한 크레인의 총괄제어 기법을 제시하고, 시뮬레이션 및 실험을 통하여 매트릭스 컨버터-유도전동기로 구동되는 크레인의 위치제어 성능을 확인한다.

Keywords

References

  1. X. Shilong, "Research of A Monitoring System for the Intelligent and Efficient Automated Handling Container Terminal", in Conf. Rec. of ICEMI, pp.518-521, 2007.
  2. T. Akamatsu, A. Kaneshige, and K. Terashima,"Real time path planning based on the potential method for an autonomous mobile overhead traveling crane", in Conf. Rec. of IEEE-ISIE, pp. 699-704, 2004.
  3. M.S. Park. D.K.Chwa; S.K.Hong, "Antisway Tracking Control of Overhead Cranes With System Uncertainty and Actuator Nonlinearity Using an Adaptive Fuzzy Sliding-Mode Control", IEEE Trans. on Industrial Electronics, Vol.55, No.11, pp. 3972-3984, Nov., 2008 https://doi.org/10.1109/TIE.2008.2004385
  4. G.Bartolini, N. Orani, A. Pisano, and E. Usai, "Load swing damping in overhead cranes by sliding mode technique", in Conf. Rec. of Decision and Control, pp. 1697-1702, 2000.
  5. Yang Jung Hua; Yang Kuang Shing, "Adaptive coupling control for overhead crane systems". in Conf, Rec. of IEEE-IECON, pp. 6-10, 2005.
  6. Backstrand, J.E, "The application of adjustable frequency drives to electric overhead cranes", in Conf. Rec. of IEEE-IAS, pp. 1986-1991, 1992.
  7. A.K.Gola and V.Agarwal, "Implementation of an Efficiency Algorithm for a Single Phase Matrix Converter", Journal of Power Electronics, Vol.9, No.2, pp. 198-206, Mar., 2009.
  8. C. Klumpner, P. Nielsen, I. Boldea, F. Blaabjerg, "A new matrix converter motor (MCM) for industry applications", IEEE Trans. on Industrial Electronics, Vol. 49, No. 2 pp. 325-335, April, 2002. https://doi.org/10.1109/41.993265
  9. P.W.Wheeler, J.Rodriguez, J.C.Clare, L.Empringham, and A.Weinstein, "Matrix Converters : A Technology Review", IEEE Trans. on Industrial Electronics, Vol. 49, No. 2 pp. 276-288, April, 2002. https://doi.org/10.1109/41.993260
  10. D. Casadei, G. Serra, A. Tani, L. Zarri, "Matrix converter modulation strategies: a new general approach based on space-vector representation of the switch state", IEEE Trans. on Industrial Electronics, Vol. 49, No. 2, pp. 370-381, April, 2002 https://doi.org/10.1109/41.993270
  11. Y.Utsumi, N.Hoshi, and K.Oguchi, "Comparison of FPGA-based Direct-Torque Controllers for Permanent Magnet Synchronous Motors", Journal of Power Electronics, Vol. 6, No. 2, pp. 114-120, April, 2009.
  12. H. H. Lee and M. H. Nguyen, "Matrix converter fed induction motor using a new modified direct torque control method", in Conf. Rec. of IEEE-IECON, pp. 2301-2306, 2004.
  13. T.Abe, T.G.Harbetler, F.Profumo, and G.Griva, "Evaluation of A High Performance Induction Motor Drive Using Direct Torque Control", in Conf. Rec. of PCC, pp. 444-449, 1993.