References
- Kabanemi, K. K., Vallancourt, H., Wang, H. and Salloum, G., 1998, "Residual Stresses, Shrinkage and Warpage of Complex Injection Molded Products: Numerical Simulation and Experiment Validation," Polymer Engineering and Science, Vol. 38, No. 1, pp. 21-37. https://doi.org/10.1002/pen.10162
- Zoetelief, W. F., Douven, L. F. A. and Ingen, A., 1996, "Residual Thermal Stresses in Injection Molded Products," Polymer Engineering and Science, Vol. 36, No. 14, pp. 1886-1896. https://doi.org/10.1002/pen.10585
- Liu, F., Zhou, H. and Li, D., 2009, "Numerical Simulations of Residual Stresses and Warpage in Injection Molding," Journal of Reinforced Plastics and Composites, Vol. 28, No. 5, pp. 571-585. https://doi.org/10.1177/0731684407085414
- Kitamura, T., Hirakata, H. and Itsuji, T., 2003, "Effect of Residual Stress on Delamination from Interface Edge Between Nano-Films," Engineering Fracture Mechanics, Vol. 70, No. 1, pp.2089-2101. https://doi.org/10.1016/S0013-7944(02)00254-0
- Yu, H. H., He, M. Y. and Hutchison, J. W., 2001, "Edge Effects in Thin Film Delamination," Acta mater, Vol. 49, No. 1, pp. 93-107. https://doi.org/10.1016/S1359-6454(00)00293-7
- Jacques, M., 1982, "An Analysis of Thermal Warpage in Injection Molded Flat Parts Due to Unbalanced Cooling," Polymer Engineering and Science, Vol. 22, No. 4, pp. 241-247. https://doi.org/10.1002/pen.760220405
- Choi, D. S. and Im, Y. T., 1999, "Prediction of Shrinkage and Warpage in Consideration of Residual Stress in Integrated Simulation of Injection Molding," Composite Structures, Vol. 47, No. 1, pp. 655-665. https://doi.org/10.1016/S0263-8223(00)00045-3
- Jansen, K. M. B. and Titomanlio, G., 1996, "Effect of Pressure History on Shrinkage and Residual Stresses Injection Molding with Constrained Shrinkage," Polymer Engineering and Science, Vol. 36, No. 15, pp. 2029-2040. https://doi.org/10.1002/pen.10598
- Chiang, K. T. and Chang, F. P., 2007, "Analysis of Shrinkage and Warpage in an Injection Molded Part with a Thin Shell Using the Response Surface Methodology," Int j adv manuf technol, Vol. 35, No. 1, pp. 468-479. https://doi.org/10.1007/s00170-006-0739-4
- Patcharaphu, S. and Mennig, G., 2006, "Simulation and Experimental Investigations of Material Distribution in the Sandwich Injection Molding Process," Polymer Plastics Tech Eng, Vol. 45, No. 1, pp. 759-768. https://doi.org/10.1080/03602550600611651
- Kim, S. Y., Oh, H. J., Kim, S. H., Kim, C. H., Lee, S. H. and Youn, J. R., 2008, "Prediction of Residual Stress and Viscoelastic Deformation of Film Insert Molded Parts," Polymer Engineering and Science, Vol. 48, No. 1, pp. 1840-1847. https://doi.org/10.1002/pen.21152
- Kim, S. Y., Kim, S. H., Oh, H. J., Lee, S. H., BaeK, S. J., Youn, J. R., Lee, S. H. and Kim, S. W., 2008, "Molded Geometry and Viscoelastic Behavior of Film Insert Molded Parts," Journal of Applied Polymer Science, Vol. 111, No. 1, pp. 642-650.
- Park, K., Ahn, J. H. and Yim, C. H., 2003, "Residual Stress Estimation and Deformaion Analysis for Injection Molded Plastic Parts Using Three Dimensional Solid Elements," Trans of the KSME (A) Vol. 27, No. 4, pp. 507-514.