한국해양공학회지 (Journal of Ocean Engineering and Technology)

  • 제23권5호
  • /
  • Pages.39-44
  • /
  • 2009
  • /
  • 1225-0767(pISSN)
  • /
  • 2287-6715(eISSN)
한국해양공학회 (Korean Society of Ocean Engineers)
권호 표지

고압 피스톤 펌프용 슬리퍼 베어링의 변형 특성에 관한 연구

A Study on the Deformation Characteristics of a Slipper Bearing for High Pressure Piston Pump

  • Koh, Sung-Wi (School of Mechanical Engineering, Pukyong National University) ;
  • Kim, Byung-Tak (School of Mechanical Engineering, Pukyong National University)
  • 발행 : 2009.10.31
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

The hydrostatic slipper bearing is generally used in high pressure axial piston pumps to support the load generated from two surfaces which are sliding relatively at low speed. The object of the bearing is to remove the possibility of direct contact by maintenance of an adequate oil film thickness between two metal surfaces. Because the bearing performance is influenced by the bearing deformation, it is highly dependent on the injection pressure, the bearing surface profile and so on. In this study, the deformation characteristics of a hydrostatic slipper bearing is investigated according to the injection pressure by the finite element analysis. In the analysis, the special boundary condition to take the fluid-structure interaction (FSI) into account is used on the interactive surface. The results, such as bearing deformation, stress and lifting force, obtained from the fully coupled analysis are compared with those from the single step sequential method.

키워드

참고문헌

  1. Kazama, T. and Yamaguchi, A. (1993a). "Application of a Mixed Lubrication Model for Hydrostatic Thrust Bearings on Hydraulic Equipment", ASME J. Tribol., Vol 115, pp 686-691 https://doi.org/10.1115/1.2921694
  2. Kazama, T. and Yamaguchi, A. (1993b). "Optimum Design of Bearing and Seal Parts for Hydraulic Equipment", Wear, Vol 161, Issues 1-2, pp 161-171 https://doi.org/10.1016/0043-1648(93)90465-X
  3. Kazama, T. and Yamaguchi, A. (1995). "Experiment on Mixed Lubrication of Hydrostatic Thrust Bearings for Hydraulic Equipment", ASME J. Tribol., Vol 117, pp 399-402 https://doi.org/10.1115/1.2831265
  4. Koc, E. and Hooke, C.J. (1997). "Considerations in the Design of Partially Hydrostatic Slipper Bearings", Tribology International, Vol 30, No 11, pp 815-823 https://doi.org/10.1016/S0301-679X(97)00064-9
  5. Koc, E., Hooke, C.J. and Li, K.Y. (1992). "Slipper Balance in Axial Piston Pumps and Motors", ASME J. Tribol., Vol 114, pp 766-772 https://doi.org/10.1115/1.2920946
  6. Manring, N., Johnson, R. and Cherukuri, H. (2002). "The Impact of Linear Deformations on Stationary Hydrostatic Thrust Bearings", ASME J. Tribol., Vol 124, pp 874-877 https://doi.org/10.1115/1.1482118
  7. Pang, Z., Zhai, W. and Shun, J. (1993). "The Study of Hydrostatic Lubrication of the Slipper in a High-Pressure Plunger Pump", STLE Tribol. Trans., Vol 36, pp 316-320 https://doi.org/10.1080/10402009308983165
  8. Sharma, S.C., Jain, S.C. and Bharuka, D.K. (2002). "Influence of Recess Shape on the Performance of a Capillary Compensated Circular Thrust Pad Hydrostatic Bearing", Tribology International, Vol 35, pp 347-356 https://doi.org/10.1016/S0301-679X(02)00013-0
  9. Zhang, H., Zhang, X., Ji, S., Guo, Y., Ledezma, G., Elabbasi, N. and deCougny, H. (2003). "Recent Development of Fluid-Structure Interaction Capabilities in the ADINA System", Computers and Structures, Vol 81, pp 1071-1085 https://doi.org/10.1016/S0045-7949(03)00009-9