Journal of the Korean Solar Energy Society (한국태양에너지학회 논문집)

The Korean Solar Energy Society (한국태양에너지학회)
권호 표지

Heat Transfer Characteristics under Saturated Nucleate Pool Boiling for Various Heating Surface Angles using Heater with Artificial Cavity

인공 캐비티를 가진 히터를 이용한 가열면 경사각에 따른 포화상태 풀 핵비등 열전달 기초연구

  • Kim, Jeong-Bae (Department of Energy System Engineering, Chungju National University)
  • 김정배 (충주대학교 에너지시스템공학과)
  • Published : 2009.08.30
Download PDF
⟨ Previous Next ⟩

Abstract

Nucleate pool boiling experiments with constant heat flux condition were performed using pure R11 and R113 for various surface angles under saturated pool condition. A circular heater of 1 mm diameter, with artificial cavity in the center, fabricated using MEMS technique and the high-speed controller were used to maintain the constant heat flux. Images of bubble growth were taken at 5,000 frames per second using a high-speed CCD camera. The bubble geometry was obtained from the captured bubble images. The effects of surface angles on the bubble growth behaviors were analyzed as dimensional scales for the initial and thermal growth regions. The parameters for the bubble growth behaviors were bubble radius, bubble growth rate, sliding velocity, bubble shape and advancing and receding contact angles. These phenomena require further analysis for various surface angles, but this study will provide good experimental data with constant heat flux boundary condition for such works.

Keywords

References

  1. Mikic, B. B.，Rohsenow, W.M. and Griffith, P.1970. On Bubble Growth Rates. Int J. Heat Mass Transfer, Vol.13, pp. 657-666 https://doi.org/10.1016/0017-9310(70)90040-2
  2. Lee, H. C., Oh, B. D., Bae, S. W., and Kim, M. H. 2003. Single Bubble Growth in Saturated Pool Boiling on a Constant Wall Temperature Surface. Int. J. of Multiphase Flow, Vol.29(12), pp. 1857-1874 https://doi.org/10.1016/j.ijmultiphaseflow.2003.09.003
  3. Kim, J.O. B. D., and Kim, M.H. 2006. Experimental Study of Pool TemperatureEffects on Nucleate Pool Boiling. Int. J. of Multiphase Flow, Vol. 32, pp. 208-231 https://doi.org/10.1016/j.ijmultiphaseflow.2005.09.005
  4. Lee，H.C.，Kim，J., Oh, B.D., and Kim, M. H. 2004. Single Bubble Growth in Saturated Pool Boiling of Binary Mixtues. Int. J. of Multiphase Flow，Vol. 30(6), pp. 697-710 https://doi.org/10.1016/j.ijmultiphaseflow.2004.05.007
  5. Githinji, P. M.and Sabersky, R. H. 1963. Some Effect of the Orientation of the Heating Surface in Nucleate Boiling. ASME J. Heat Transfer, Vol. 85, pp. 379 https://doi.org/10.1115/1.3686129
  6. Chen, L.T. 1978. Heat Transfer to Pool Boiling Freon from Inclined Heating Plate. Lett. Heat Mass Transfer, Vol. 5, pp. 111-120 https://doi.org/10.1016/0094-4548(78)90025-5
  7. Jung, D. S., Venart, J. E. S., and Sousa, A. C. M., 1987. Effects of Enhanced Surfaces and Surface Orientation on Nucleate and Film Boiling Heat Transfer in R-11. Int. J. Heat Mass Transfer, Vol. 30, pp. 2627-2639 https://doi.org/10.1016/0017-9310(87)90144-X
  8. Chang, J Y.and You, S. M. 1996. Heater Orientation Effects on Pool Boiling Microporous-enhanced Surfaces in Saturated FC-72. ASME J. Heat Transfer, Vol. 118, pp. 937-943 https://doi.org/10.1115/1.2822592
  9. Lee, J. C，ho，K., Song, I.S., Kim, C. B., and Son, S. Y. 2003. Microscale Bubble Nucleation from an Artificial Cavity in Single Microchannel. ASME J. of Heat Transfer, Vol. 125, pp. 545 https://doi.org/10.1115/1.1617074