Effect of High Injection Pressure and Ambient Pressure on the DME Spray Characteristics Injected Through a Common-rail Diesel Injector

커먼레일 디젤 인젝터에서 연료 분사 및 분위기 압력이 DME 분무 특성에 미치는 영향

  • 김형준 (한양대학교 대학원 기계공학부) ;
  • 박수한 (한양대학교 대학원 기계공학부) ;
  • 이창식 (한양대학교 기계공학부)
  • Published : 2009.06.30

Abstract

The aim of this investigation is to study the effect of the high injection pressure on the dimethyl ether (DME) spray characteristics injected through a common-rail diesel injector under various ambient pressures. In order to investigate the effect of the injection pressure and ambient condition, the common-rail injection system with two high pressure pumps and high pressure chamber pressurized up to 40 bar were used, respectively. Spray images of DME fuel obtained from a visualization system composed of high speed camera and two metal halide lamps as the light source. From the obtained images, the spray behaviors such as a spray development process, spray tip penetration, spray width, and spray cone angle were measured for analyzing the DME spray characteristics under various experimental conditions. It was found that the spray development slowed as the ambient pressure increased and spray tip penetration at injection pressure of 90 MPa is longer than that at 50 MPa. In addition, the spray width at the end stage of injection decreased under the atmospheric conditions due to the evaporation property of DME fuel, and DME spray shows narrow spray cone angle according to the injection pressure increased.

Keywords

References

  1. M. Y. Kim, S. H. Bang and C. S. Lee, "Experimental investigation of spray and combustion characteristics of dimethyl ether in a common-rail diesel engine", Energy & Fuels, Vol. 21, No.2, 2007, pp. 793-800. https://doi.org/10.1021/ef060310o
  2. B. Gui, T. L. Chan, C. W. Leung, J. Xiao, H. Wang and L. Zhao, "Modeling study on the combustion and emissions characteristics of a light-duty Dl diesel engine fueled with dimethyl ether (DME) using a detailed chemical kinetic mechanism", SAE tech. paper series, 2004, 2004-01-1839.
  3. M. Y. Kim, S. H. Yoon, B. W. Ryu and C. S. Lee, "Combustion and emission characteristics of DME as an alternative fuel for compression ignition engines with a high pressure injection system", Fuel, Vol. 87, 2008, pp. 2779-2786. https://doi.org/10.1016/j.fuel.2008.01.032
  4. H. Teng, J. C. McCandless and J. B. Schneyer, "Thermochemical characteristics of dimethyl ether-An alternative fuel for compression-ignition engines", SAE tech. paper series, 2001, 2001-01-0154.
  5. H. Teng, J. C. McCandless and J. B. Schneyer, "Viscosity and lubricity of (liquid) dimethyl Ether-An alternative fuel for compression-ignition engines", SAE tech. paper series, 2002, 2002-01-0862.
  6. H. Teng, J. C. McCandless and J. B. Schneyer, "Compression ignition delay (physical+chemical) of dimethyl ether-An alternative fuel for compression-ignition engines", SAE tech. paper series, 2003, 2003-01-0759.
  7. H. Teng, J. C. McCandless and J. B. Schneyer, "Thermodynamic properties of dimethyl ether-An alternative fuel for compression-ignition engines", SAE tech. paper series, 2004, 2004-01-0093.
  8. H. Teng and J. C. McCandless, "Comparative study of characteristics of diesel-fuel and dimethyl-ether sprays in the engine", SAE tech. paper series, 2005, 2005-01-1723.
  9. H. K. Suh, S. W. Park and C. S. Lee, "Atomization Characteristics of Dimethyl Ether Fuel as an Alternative Fuel Injected through a Common-Rail Injection System", Energy & Fuels, Vol. 20, No.4, 2006, pp. 1471-1481. https://doi.org/10.1021/ef050420f
  10. H. J. Kim, H. K. Suh, S. H. Park and C. S. Lee, "An experimental and numerical investigation of atomization characteristics of biodiesel, dimethyl ether, and biodiesel-ethanol blended fuel", Energy & Fuels, Vol. 22, No.3, 2008, pp. 2091-2098. https://doi.org/10.1021/ef700692w
  11. H. J. Kim, H. K. Suh and C. S. Lee, "Numerical and experimental study on the comparison between diesel and dimethyl Ether (DME) spray behaviors according to combustion chamber shape", Energy & Fuels, Vol. 22, No.4, 2008, pp. 2851-2860. https://doi.org/10.1021/ef8000696