DOI QR코드

DOI QR Code

Development and Strength Evaluation of Ring Projection Welding Process of the Microminiature Tube and Tubesheet

초소형 튜브와 튜브판의 링 프로젝션 용접 공정개발 및 강도 평가

  • 윤영현 (부경대학교 조선시스템관리공학협동과정) ;
  • 김현준 ((주) 동화엔텍 기술 연구소) ;
  • 김창수 ((주) 동화엔텍 기술 연구소) ;
  • 조상명 (부경대학교 소재프로세스공학과)
  • Published : 2009.04.30

Abstract

Microminiature heat exchanger has been applied to the gas turbine in order to increase energy efficiency. During the production of microminiature heat exchanger, however, it is very difficult to weld tube to tubesheet. In this study, therefore, welding process of resistance ring projection was used, and weld tensile tests were performed. Sound weld joint was obtained as a result of applying resistance ring projection welding to microminiature heat exchanger to tubesheet. Cold weld occurred at under 1600A. Even though tensile strength was increased with increasing current, splash occurred and tensile strength decreased at 2000A due to the excessive current. Therefore it was determine that the optimal current is 1900A. As result of tensile tests based on ASME code for tube to tubesheet weldment, rupture position was weldment due to Fs(Fractured section) of nugget, which was smaller than tube thickness (t), and it was proven as a partial strength welding because of the average joint efficiency fr = 0.90.

Keywords

References

  1. K.H.Kim, G.H.Kim, M.G.Lee, H.H.Kim, S.W.Kim, S.H.Kim, "Preliminary Investigation on Joining Performance of Intermediate Heat Exchanger Candidate Materials of Very High Temperature Reactor(VHTR) by Vacuum Brazing" KWS 2005-Autumn, 195-197 (in Korean)
  2. H.Y.Cho, G.H.Kim, J.H.Lee, J.Seo, M.S.Choe, "Finite element analysis of laser welding of micro heat exchanger", Korean Society Of Laser Processing, 2005, 40-44 (in Korean)
  3. H.S.Kang, J.Seo, J.H.Lee J.O.Kim, S.H.Yu, H.Y.Cho "Temperature Characteristics of Laser Welding Parts of Micro Heat Exchanger", KWS 2006-Spring, 65-67 (in Korean)
  4. AWS Welding Handbook, Ninth Editon, Volume 2, Chapter 2
  5. J.K.Min, Y.K.Oh, G.S.Kim, "A Study on the Spot Weldability of Automotive Steel Sheets", Journal of KWS. 14-3 (1996), 41-46 (in Korean)
  6. Murat Vural, Ahmet Akkus, "On the resistance spot weldability of galvanized interstitial free steel sheets with austenitic stainless steel sheets", Journal of Materials Processing Technology, 153–154, 2004
  7. Boiler and Pressure Vessel Code ASME, Section Ⅷ -Division 1, 2001
  8. AWS Resistance Welder Manufacturers Association : Resistance welding manual Fourth edition(19889. 10), 4.1-4.10
  9. M.L. Kuntz, J.C. Bohr "Assessing Weldability of Projection Welding Fasteners to AHSS using Finite Element Analysis", 2000 Town Center Suite 320
  10. 최송천, 한상인, "공정플랜트 고온 튜브 수명연장 및 건정성 평가에 관한 연구", 한국가스안전공사, (2002) (in Korean)
  11. Kwang soo Yu, Song Chun Choi, Yong-Soo Kim, "Finess-For-Service of Heat Exchanger Tubing Expansion Transition Zone", Journal of the Korean Institute of Gas, 11-3, 2007
  12. Jose Luis Otegui, Pablo Gabriel Fazzini, "Failure analysis of tube–.tubesheet welds in cracked gas heat exchangers", Engineering Failure Analysis 11 903-913, 2004 https://doi.org/10.1016/j.engfailanal.2004.01.003
  13. C.R. Simmons, "Gas Turbine Manual", 1968, Chapter 13, 239-255
  14. Hee-Seok Chang, Seung-Kyu Park, "Micro spot welding technology for microminiature parts", Journal of KWS. 22-4 (2004), 12-19 (in Korean)

Cited by

  1. Manufacturing and mechanical evaluation of cooled cooling air (CCA) heat exchanger for aero engine vol.17, pp.9, 2016, https://doi.org/10.1007/s12541-016-0143-4