DOI QR코드

DOI QR Code

무윤활 압연한 알루미늄 합금의 집합조직과 성형성

Texture and Formability Development of Non-lubrication Rolled Al Alloy Sheet

  • 발행 : 2009.04.01

초록

Formability and other mechanical properties of sheet metals are strongly dependent on the texture. It was studied to improve the formability of the Al alloy(AA3003) sheets which were rolled under the non-lubrication condition and subsequent heat treated. In the non-lubrication rolled and subsequent heat treated Al alloy sheet, the variation of the plastic strain ratios were investigated in this study. Non-lubrication rolled Al sheets showed a fine grain size and after subsequent heat treated specimens showed that the $\beta$-fiber texture component was increased. The plastic strain ratios of the non-lubrication rolled and subsequent heat treated Al alloy sheets were about two times higher than those of the original Al sheets. These could be related to the formation of $\beta$-fiber texture components through the non-lubrication rolling and subsequent heat treatment in Al sheet.

키워드

참고문헌

  1. P. H. Lequeu and J. J. Jonas, 1988, Modeling of the plastic anisotropy of textured sheet, Metal. Trans. A, Vol. 19A, p. 105 https://doi.org/10.1007/BF02669819
  2. M. Hatherly and W. B. Hutchinson, 1979, An Introduction to Textures in Metals, Institution of Metallurgists, London
  3. J. Hirsch and K. Lucke, 1988, Mechanism of deformation and development of rolling textures in polycrystalline F. C. C. metals-simulation and interpretation of experiments on the basis of Taylor-tape theories, Acta Metall. Vol. 36, pp. 2883-2904 https://doi.org/10.1016/0001-6160(88)90173-3
  4. A. K. Vasudevan and R. D. Doherty, 1989, Aluminum Alloys-Contemporary Research and Applications, Treatise on Materials Science and Technology, Vol. 31, Academic Press
  5. T. Kamijo and H. Fukutomi, 1995, In microstructural and crystallographic aspects of recrystallization (edited by N. Hansen, D. J. Jensen, Y. L. Liu and B. Ralph) Riso National Laboratory, Roskilde, Denmark, p. 377
  6. C.-H. Choi, K.-H. Kim, S.-Y. Jeong and D. N. Lee, 1997, Analysis of texture in aluminum alloy sheets rolled using asymmetric roll, J. of Korean Inst. Met. Mater. Vol. 35/4, p. 429
  7. K. J. Kim, H.-T. Jeong, K. S. Shin and C.-W. Kim, 2007, Texture evolution of rolled AA5052 alloy sheets after annealing, J. Mater. Process, Vol 187-188, pp. 578-581 https://doi.org/10.1016/j.jmatprotec.2006.11.214
  8. S. Akramov, M. G. Lee, I. Kim, D. Y. Sung and B. H. Park, 2005, The Texture of 1050 Al Sheet Produced by Equal Channel Angular Pressing, Mater. Sci. Forum, Vol. 475/479, p. 417 https://doi.org/10.4028/www.scientific.net/MSF.475-479.417
  9. S. Akramov, M. G. Lee, I. Kim, D. Y. Sung, B. H. Park and I. Kim, 2005, R-Value and Texture Change of AA 1050 Al Alloy Sheet by Equal Channel Angular Pressing, Mater. Sci. Forum, Vol. 495/497 p. 803 https://doi.org/10.4028/www.scientific.net/MSF.495-497.803
  10. S. Akramov, I. Kim, M. G. Lee and B. H. Park, 2006, Sheet Formability of AA 1050 Al Alloy Sheet by Equal Channel Angular Pressing of Route C Type, Sol. State Phenon., Vol. 116/117, p. 324 https://doi.org/10.4028/www.scientific.net/SSP.116-117.324
  11. S. Akramov, I. Kim and N. J. Park, 2007, Texture and Formability of Frictionally Rolled AA 1050 Aluminum Alloy Sheets, Adv. Mater. Research, Vol. 26/28, p. 393 https://doi.org/10.4028/www.scientific.net/AMR.26-28.393
  12. I. Kim, S. Akramov and H. B. Jeong, 2009, Texture and Formability Development of Asymmetry Rolled AA3003 Al Alloy Sheet, Mod. Phys. letter B, in press https://doi.org/10.1142/9789814261579_0082
  13. I. Kim, S. Akramov, H. B. Jeong and T. K. No, 2009, Texture Development and Drawability of Frictional Rolled AA 5052 Al Alloy Sheet, Mod. Phys. letter B, in press https://doi.org/10.1142/S021797920805139X
  14. S. Akramov and I. Kim, 2009, Texture analysis and r-value variation after severe shear deformed and hear treated Al alloy sheets, J. of Physics, in press. https://doi.org/10.1088/1742-6596/165/1/012001
  15. H. J. Bunge, 1982, Texture Analysis in Material Science, Butterworth, Guildford, UK

피인용 문헌

  1. Texture and Plastic Strain Ratio Changes with the Number of Passes of Asymmetric Rolling in AA1050 Al Alloy Sheet vol.19, pp.8, 2010, https://doi.org/10.5228/KSTP.2010.19.8.502
  2. Texture and Plastic Strain Ratio Changes during a 2 Step Asymmetric Rolling and Annealing of AA5083 Al Alloy Sheet vol.23, pp.2, 2014, https://doi.org/10.5228/KSTP.2014.23.2.82