Elastomers and Composites

  • 제43권2호
  • /
  • Pages.104-112
  • /
  • 2008
  • /
  • 2092-9676(pISSN)
  • /
  • 2288-7725(eISSN)
한국고무학회 (The Rubber Society of Korea)
권호 표지

EPDM/SBR 블렌드 가황체의 경화특성, 기계적 성질 및 내오존성

Cure characteristics, Mechanical Properties and Ozone Resistance of EPDM/SBR Blend Vulcanizates

  • 박찬영 (부경대학교 공과대학 응용화학공학부)
  • Park, Chan-Young (Division of Applied Chemical Engineering, Pukyong National University)
  • 발행 : 2008.06.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

통상적인 고무블렌드 방법에 따라 개방식 2-롤밀을 사용하여 ethylene propylene diene terpolymer (EPDM)과 styrene butadiene rubber (SBR) 블렌드 배합물을 제조하여, 이들의 경화 특성, 기계적 성질 및 내오존성 등을 검토하였다. SBR함량이 증가할수록 가황곡선의 토크가 증가하였다. 최대 토크는 SBR 25wt% 일 때 가장 낮았으며 그 이상의 SBR 량에서는 직선적으로 증가하였다. 스코치시간 및 최적경화시간은 SBR고무 함량이 증가함에 따라 감소하였다. 경도는 SBR 함량이 50wt% 일 때 최고값을 보였으며 그 전후에서는 감소하는 경향을 보였다. 내오존시험에 있어서 소량의 EPDM 고무의 첨가에 의하여 내오존성이 크게 개선됨을 확인할 수 있었다.

The ethylene propylene diene terpolymer (EPDM) blends with styrene butadiene rubber (SBR) were prepared from an open 2-roll mill following the conventional rubber blend method, and then cure characteristics, mechanical properties and ozone resistance were subsequently examined. With incorporation of SBR the torque value of the EPDM and SBR blends showed a gradual increase in the cure curve. The maximum torque value was obtained with lowest level at 25wt% of SBR and it was increased linearly with more than 25wt%. As the SBR loading increased scorch time and optimum cure time decreased. Hardness represented a maximum at 50wt% of SBR. However upper and lower than that value it decreased. It was found that the unfavorable characteristics of ozone resistance of pure SBR was significantly improved through the blending of SBR with EPDM.

키워드

참고문헌

  1. S. C George, K. N. Ninan, G. Greonincks, and S. Thomas, "Styrene-butadiene rubber/natural rubber blends: morphology, transport behaviour, and dynamic mechanical properties", J. App. Polym. Sci., 78, 1280 (2007)
  2. E. T. McDonel, K. C. Baranwal, J. C. Andries, D. R. Paul, and S. Newman, Polymer blends, vol 2, chapter 19 New York: Academic Press; (1978)
  3. B. D. Favis and J. P. Chalifoux, "Influence of composition on the morphology of polypropylene/ polycarbonate blends", Polymer, 29, 1761 (1988) https://doi.org/10.1016/0032-3861(88)90388-6
  4. S. Thomas and G. Groeninckx, "Nylon 6/ethylene propylene rubber (EPM) blends: Phase morphology development during processing and comparison with literature data", J. Appl. Polym. Sci., 71, 1405 (1999) https://doi.org/10.1002/(SICI)1097-4628(19990228)71:9<1405::AID-APP6>3.0.CO;2-E
  5. H. Varghese, S. S. Bhagawan, S. S. Rao, and S. Thomas, "Morphology, mechanical and viscoelastic behaviour of blends of nitrile rubber and ethylenevinyl acetate copolymer", European Polymer Journal, 31, 957 (1995) https://doi.org/10.1016/0014-3057(95)00056-9
  6. S. Chakrit, S. B. Limcharoen, and J. Thunyarittikorn, "Relationships among blending conditions, size of dispersed phase, and oil resistance in natural rubber and nitrile rubber blends", J. Appl. Poly. Sci., 82, 1232 (2001) https://doi.org/10.1002/app.1957
  7. S. Chakrit,, P. Saeoui, and J. Guaysomboon, "Relationship among phase morphology, oil resistance, and thermal aging properties in CPE/NR blends: effect of blending conditions", J. Appl. Poly. Sci., 90, 4038 (2004) https://doi.org/10.1002/app.13164
  8. N. Sachin, D. Surekha, G. S. Rao, and K. V. Rao, "Relationship between morphology and mechanical properties of binary and compatibilized ternary blends of polypropylene and nylon 6", J. Appl. Poly. Sci., 61, 97 (1996) https://doi.org/10.1002/(SICI)1097-4628(19960705)61:1<97::AID-APP11>3.0.CO;2-X
  9. I. Abdullah, S Ahmad, and C. S. Sulaiman, "Blending of natural rubber with linear low-density polyethylene", J. Appl. Poly. Sci., 58, 1125 (1995) https://doi.org/10.1002/app.1995.070580706
  10. H. M. Dahlan, M. D. Zaman, and A. Ibrahim, "Liquid natural rubber (LNR) as a compatibilizer in NR/LLDPE blends", J. Appl. Poly. Sci., 78, 1776 (2000) https://doi.org/10.1002/1097-4628(20001205)78:10<1776::AID-APP90>3.0.CO;2-G
  11. C. Sirisinha, S. Limcharoen, and J. Thunyarittikorn, "Oil resistance controlled by phase morphology in natural rubber/nitrile rubber blends", J. Appl. Poly. Sci., 87, 83 (2003) https://doi.org/10.1002/app.11673
  12. S. Thomas and G. Groeninckx, "Reactive compatibilisation of heterogeneous ethylene propylene rubber (EPM)/nylon 6 blends by the addition of compatibiliser precursor EPM-g-MA", Polymer, 40, 5799 (1999) https://doi.org/10.1016/S0032-3861(98)00813-1
  13. R. Fayt, R. Jerome, and P. H. Teyssie, "Molecular desing of mulyi component polymer systems. III. Comparative behaviour of pure and tapered block copoltmer in emulsification of blends of lowdensity polyethylene and polystyrene", J Polym Sci B: Polym Phys Edition, 20, 1209 (1982)
  14. H. Ismail and H. M. Hairunezam, "The effect of a compatibilizer on curing characteristics, mechanical properties and oil resistance of styrene butadiene rubber/epoxidized natural rubber blends", European polymer Journal, 37, 39 (2001) https://doi.org/10.1016/S0014-3057(00)00099-9
  15. A. T. Koshy, B. Kuriakose, and S. Thomas, "Studies on the effect of blends ratio and cure system on the degradation of rubber-ethylene vinylacetate rubber blends" Polym Degard Stabil., 36, 137 (1992) https://doi.org/10.1016/0141-3910(92)90150-4
  16. A. T. Koshy, B. Kuriakose, S. Thomas, and S. Varghese, "Studies on the effect of blend ratio and crosslinking system on thermal, X-ray and dynamic mechanical properyies of blends of natural rubber and ethylene-vinyl acetate copolymer", Polymer, 34, 3428 (1993) https://doi.org/10.1016/0032-3861(93)90472-M
  17. A. T. Koshy, B. Kuriakose, S. Thomas, and S. Varghese, "Viscoelastic properties of silica filled natural rubber and ethylene-vinyl acetate copolymer blend", Polym Plast Technol., 433, 149 (1999)
  18. P. Jansen and B. G. Soares, "Effect of compatibilizer and curing system on the thermal degradation of natural rubber eva copolymer blends", Polym. Degrad. Stabil., 52, 95 (1996) https://doi.org/10.1016/0141-3910(95)00238-3
  19. P. Jansen, A. S. Gomes, and B. G. Soates, "The use of EVA-containing mercopto group in natural rubber-EVA blends. 2. The effect of curing system on mechanical and thermal properties of the blends". J Appl Polym Sci., 61, 591 (1996) https://doi.org/10.1002/(SICI)1097-4628(19960725)61:4<591::AID-APP2>3.0.CO;2-G
  20. 山下 晋三, ゴム 奇術の 基礎, 日本ゴム 協會, 135 (1985)
  21. ASTM Designation, D-2084-76T, 1972
  22. ASTM Designation, D-412-66T, 1967
  23. ASTM Designation, D-573, 1975
  24. R. P. Brown, Physical Testing of Rubber, 2nd ed. Elsevier Apple. Sci., London & New York, 291 (1986)
  25. D. W. Cho and C. H. Yoon, "Vulcanization study by DSC", J. Kor. Inst. Rubber Ind., 27, 275 (1992)
  26. P. Sae-oui, C. Sirisinha, U. Thepsuwan, and P. Thapthong, "Influence of accelerator type on properties of NR/EPDM blends", Polymer Testing, 26, 1062 (2007) https://doi.org/10.1016/j.polymertesting.2007.07.004