THE SHEAR BOND STRENGTH OF DENTAL ADHESIVES ON PRIMARY AND PERMANENT TEETH

유치와 영구치에서 치과용 접착제의 전단결합강도

The objective of this study was to compare the shear bond strengths of five adhesive systems to the enamel and dentin of primary and permanent teeth. Fifty noncarious primary and fifty permanent teeth were collected and stored in an 0.1% thymol solution at room temperature after extraction. The tested adhesives were: Adper Scotchbond Multi-purpose Plus Adhesive (SM) Adper Single bond 2 (SB), Clearfil SE Bond (SE), Adper Prompt L-Pop (PL), GBond (GB). For the shear bonding test, the labial and lingual surfaces of primary and permanent teeth were used. To obtain a flat surface, the labial and lingual surfaces of the teeth were sanded on $SiO_2$ with number 600 grit and then divided into 20 groups of 10 surfaces each. All samples were theromocycled in water $5^{\circ}C$ and $55^{\circ}C$ for 1000 cycles. The results were as follows: 1. For primary enamel, shear bond strengths of SM and SB were significantly higher than that of SE and also SM, SB, and PL were higher than GB(p<0.05). 2. For primary dentin, there were no significant differences among the shear bond strengths of any other bonding systems except difference between SE and GB. 3. For permanent enamel, SB showed significantly higher mean shear bond strength than those of any other bonding systems(p<0.05). 4. For permanent dentin, SM showed significantly higher mean shear bond strength than that of PL and GB(p<0.05). 5. Between the primary enamel and dentin, there were significant differences in SM, SB, and GB, whereas there was statistically significant difference in PL between the permanent enamel and dentin(p<0.05). 6. Between the primary and permanent teeth on enamel, there were no significant differences among all bonding systems, whereas there were statistically significant differences in SM and SB between the primary and permanent teeth on dentin(p<0.05).

본 연구에서는 최근에 개발된 치과용 접착제를 대상으로 유치와 영구치의 법랑질과 상아질에 대한 결합력을 비교 평가하여 임상에서 상아질 접착제를 적절하게 선택하는데 도움을 주고자 시행하였다. 실험재료로 Adper Scotchbond Multi-purpose Plus Adhesive (SM; 3M ESPE, USA), Adper Single bond 2 (SB; 3M ESPE, USA), Clearfil SE Bond (SE; Kuraray Medical Inc., Japan), Adper Prompt L-Pop (PL; 3M ESPE, USA), G-Bond (GB; GC Cooperation Toyko, Japan)를 이용하여 전단결합강도를 평가하여 다음과 같은 결과를 얻었다. 1. 유치 법랑질에서 전단결합강도는 SM이 $28.47{\pm}7.93\;MPa$로 가장 높았고 SB ($28.18{\pm}6.84$), PL ($24.02{\pm}6.14$), SE ($21.70{\pm}6.56$), GB ($17.70{\pm}6.68$) 순이었다. SM과 SB는 SE보다 통계적으로 유의하게 높은 결합강도를 보였으며, SM, SB, PL은 GB보다 높았다(p<0.05). 2. 유치 상아질에서 전단결합강도는 SE가 $28.72{\pm}14.44MPa$로 가장 높았고, PL ($20.10{\pm}6.13$), SM ($17.72{\pm}10.65$), SB ($15.48{\pm}2.66$), GB ($10.10{\pm}5.45$) 순이었으며 SE와 GB간에는 유의한 차이가 있었으나, 다른 군들 간에는 유의한 차이가 없었다. 3. 영구치 법랑질에서의 전단결합강도는 SB가 $28.36{\pm}5.68\;MPa$로 가장 높았고 SM ($22.77{\pm}4.63$), PL ($22.05{\pm}6.57$), SE ($21.74{\pm}4.62$), GB ($15.60{\pm}6.75$)순이었다. SB는 다른 접착제보다 통계적으로 유의하게 높은 결합력을 나타냈으며, GB는 가장 낮은 결합력을 보였다(p<0.05). 4. 영구치 상아질에서의 전단결합강도는 SM이 $28.22{\pm}5.56\;MPa$로 가장 높았고, SB ($21.68{\pm}7.44$), SE ($20.13{\pm}9.88$), GB ($14.30{\pm}6.81$), PL ($14.18{\pm}5.88$)순이었으며, SM은 PL, GB와 유의한 차이가 있었다(p<0.05). 5. 유치의 법랑질과 상아질 간에는 SM, SB, GB에서 유의한 차이가 있었고, 영구치 법랑질과 상아질 간에는 PL에서 유의한 차이가 있었다(p<0.05). 6. 유치 법랑질과 영구치 법랑질 간에는 모든 접착제에서 유의한 차이가 없었으나, 유치 상아질과 영구치 상아질 간에는 SM과 SB에서 유의한 차이가 있었다(p<0.05).