초록
이 연구는 강화형 미세입자 복합레진인 Micronew에 Biscover 레진전색제를 적용한 후 칫솔마모시험을 시행하여 복합레진 표면의 조도와 현미경적 변화를 비교함으로써 레진전색제를 복합레진 표면에 재적용할 시기를 알아보고자 하였다. 분리 가능한 알루미늄 판과 복합레진을 이용하여 $8\times3\times2mm$ 크기의 복합레진 시편 200개를 제작하였다. 복합레진 시편의 양쪽표면을 Sof-Lex disc로 거친 입자에서 중간 입자까지 마무리한 후 실온의 증류수에 24시간 동안 보관하였다. 시편은 disc로 마무리만 시행한 F군 (n = 10)과 마무리 후 레진전색제인 Biscover를 적용한 B군 (n = 190)으로 분류하였다. B군은 다시 칫솔질을 가하지 않은 B-IM군 (n = 10)과 칫솔질을 가한 군 (n = 180, B-1군에서 B-18 군)으로 분류하였다. 칫솔질을 가한 군은 칫솔마모검사기의 수조에 페리오 치약과 증류수를 무게 비 50 : 50으로 혼합하여 부은 다음, 홈이 파진 알루미늄 블록에 각 군의 시편을 위치시키고 칫솔을 고정장치에 부착하여 전, 후 왕복운동을 가하여 칫솔질을 가하였다. 칫솔질은 B-1 군에서 B-18군 까지 각각 900회씩 증가시켜 16,200회 까지 시행하였다 표면조도측정기를 사용하여 각 군의 복합레진 표면의 평균 표면조도 값 (Ra)을 산출한 후 통계적으로 분석하였고, 주사전자현미경하에서 각 군의 대표적인 시편 1개를 관찰하여 다음과 같은 결과를 얻었다. 1. F군의 Ra는 $0.898{\pm}0.145{\mu}m$, B-IM군의 Ra는 $0.289{\pm}0.142{\mu}m$를 나타냈으며, B-1 군에서 B-18 군까지의 Ra는 점차적으로 증가하여 B-1 군에서 $0.299{\pm}0.48{\mu}m$, B-18 군에서 $0.642{\pm}0.313{\mu}m$까지 나타났다. 2. Ra 최종 군집중심은 군집 1 $(B-IM\simB-7)$에서 $0.361{\mu}m$, 군집 2 $(B-8\simB-14)$에서 $0.511{\mu}m$, 군집 3 $(B-15\simB-18)$에서 $0.624{\mu}m$를 나타내어 각 군집의 Ra 최종 군집중심 간에 통계학적으로 유의한 차이를 나타내었다. (F = 49.705, p = 0.000) 3. B-IM군의 Ra 증감율은 F 군에 비해 210.72%감소되었으며, B-8 군과 B-15군의 Ra 증감율은 B-IM군에 비해 각각 35.49%와 51.35% 증가되었다. 4. FE-SEM 관찰에서 B-IM 군은 매우 평활한 복합레진 표면을 나타내었고, B-8 군은 전체적으로 평활한 복합레진 표면을 보였지만 표면에 수직으로 아주 얕은 흠집을 나타내었다. B-15 군은 복합레진 표면의 중앙에서 B-8군보다 더 넓고 불규칙한 수직의 흠집을 나타내었고, B-18군은 복합레진 표면 전체에 넓은 흠집을 나타내었다.
The purpose of this study was to evaluate the abrasion resistance of surface penetrating sealant which was applied on a composite resin restoration and to provide proper time to reapply sealant on composite resin surface. Two hundred rectangular specimens, sized $8\times3\times2mm$, were made of Micronew (Bisco, Inc., Schaumburg, IL, U.S.A) and divided into two groups; F group (n = 10) was finished with coarse and medium grit of Sof-Lex discs and BisCoverwas applied B group (n = 190) after finishing with discs. B group was again subdivided into nineteen subgroups From B-1 group to B-18 group were subjected to toothbrush abrasion test using a distilled water-dentifrice slurry and toothbrush heads B-IM group was not subjected to toothbrush abrasion test. Average surface roughness (Ra) of each group was calculated using a surface roughness tester (Surfcorder MSE-1700: Kosaka Laboratory Ltd., Tokyo, Japan) . A representative specimen of each group was examined by FE-SEM (S-4700: Hitachi High Technologies Co., Tokyo, Japan). The data were analysed using cluster analysis, paired t-test, and repeated measure ANOVA. The results of this study were as follows; 1. Ra off group was $0.898{\pm}0.145{\mu}m$ and B-IM group was $0.289{\pm}0.142{\mu}m$. Ra became higher from B-1 group $(0.299{\pm}0.48{\mu}m$ to B-18 group $(0.642{\pm}0.313{\mu}m$. 2. Final cluster center of Ra was $0.361{\mu}m$ in cluster 1 $(B-IM\simB-7)$, $0.511{\mu}m$ in cluster 2 $(B-8\simB-14)$ and $0.624{\mu}m$ in cluster 3 ($(B-15\simB-18)$. There were significant difference among Ra of three clusters. 3 Ra of B-IM group was decreased 210.72% than Ra of F group. Ra of B-8 group and B-15 group was increased 35.49% and 51.35% respectively than Ra of B-IM group. 4. On FE-SEM, B-IM group showed the smoothest resin surface. B-8 group and B-15 group showed vertically shallow scratches , and wide and irregular vertical scratches on composite resin surface respectively. Within a limitation of this study, finished resin surface will be again smooth and glazy if BisCover would be reapplied within 8 to 14 months after applying to resin surface.