International Journal of Automotive Technology

  • 제8권6호
  • /
  • Pages.799-806
  • /
  • 2007
  • /
  • 1229-9138(pISSN)
  • /
  • 1976-3832(eISSN)
한국자동차공학회 (The Korean Society of Automotive Engineers)
권호 표지

DESIGN OF A SINGLE MODE VARIABLE BRIDGE TYPE SPLIT-POWERED CVT WITH AN INNER-SPHERICAL CONTINUOUSLY VARIABLE UNIT

  • Seong, S.H. (Department of Mechanical Design Engineering, Pusan National University) ;
  • Lee, H.W. (Department of Mechanical Design Engineering, Pusan National University) ;
  • Choi, J.H. (Department of Mechanical Design Engineering, Pusan National University) ;
  • Park, N.G. (Department of Mechanical Design Engineering, Pusan National University)
  • 발행 : 2007.12.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

One method for improving the torque capacity of the CVT is to use a split-powered CVT(SPCVT) to reduce the power transmitted into a continuously variable unit(CVU). A variable bridge SPCVT with two planetary gear units(PGUs), which are composed of a sun gear, a ring gear, and carrier and planetary gears, can minimize the power to the CVU. However, a SPCVT with a conventional CVT should possess a dual mode, which would allow the conventional CVT to be used at high speeds and an additional gear train to be used at low speeds. The inner-spherical CVU(ISCVU) with an inner and outer spherical contact mechanism developed in this study can cover the range from low to high speeds. The rated power and the overall speed ratios were 100 kW and $0.09{\sim}0.36$, respectively. Power efficiency was numerically calculated to be over 90% over the speed ratio range of $0.1{\sim}0.29$. The maximum shear stress at the two contact areas of the rotor pairs, the minimum life and the overall size were estimated to be 700 MPa, 276 kh and $350{\times}350{\times}400mm^3$, respectively. This study shows that an ISCVU and a variable bridge type PGU can realize the SPCVT with a single mode for a vehicle.

키워드

참고문헌

  1. Carter, J. and Miller, D. (2003). The design and analysis of an alternative traction drive CVT. Transmission & Driveline Systems Symp., SAE Paper No. 2003-01-0970, Detroit, Michigan, USA
  2. Cheney, E. W. (1966). Introduction to Approximation Theory. McGraw-Hill. New York
  3. Heilch III, F. W. and Shube, E. E. (1983). Traction Drives; Mechanical Engineering Series. Marcel Dekker. New York. 177−205
  4. Lee, H. and Kim, H. (2003). CVT ratio control for improvement of fuel economy by considering powertrain response lag. KSME Int. J. 17, 11, 1725−1731
  5. Mattson, P. (1994). An infinitely variable spilt-power transmission with a traction ball drive variator. VDI Berichte, 1170, 137−152
  6. Mucino, V. H., Lu, Z., Smith, J. E., Kimcikiewicz, M. and Cowan, B. (2001). Design of continuously variable power split transmission systems for automotive applications. Proc. Instn. Mech. Engrs.: Part D, 215, 469−478
  7. Norton, R. L. (2000). Machine Design - An Integrated Approach. 2nd edn. Prentice-Hall. New Jersey
  8. Pfiffner, R., Guzzella, L. and Onder, C. H. (2003). Fueloptimal control of CVT powertrains. Control Engineering Practice 29, 11, 329−336
  9. Pichard, J. and Besson, B. (1981). Hydrostatic power splitting transmissions design and application example. ASME J. Engineering for Power, 103, 168−173
  10. Russner, D. R. and Singh, Y. P. (2004). Design of input coupled split power transmissions, arrangements and their characteristics. Trans. ASME, 126, 542−550
  11. Ryu, J. H., Kim, Y. K. and Park, N. G. (2002). A split power continuously variable transmissions (SPCVT) for bicycle use. Proc. Small Engine and Transmission Conf. JSAE 20024265, Kyoto, Japan
  12. Seong, S. H., Ryu, J. H., Lee, H. W. and Park, N. G. (2005). Conceptual design of inner-spherical continuously variable transmission for bicycle usage. Int. J. Automotive Technology 6, 5, 467−473
  13. Shoji, A. and Kawashima, G. (2002). The Development of the traction drive mechanism made of the plastic magnet. Proc. Design Engineering Technical Conf. and Computers and Information in Engineering Conf., Illinois, USA
  14. Tanaka, H. and Eguchi, M. (1991). Speed ratio control of a half-toroidal traction drive CVT. JSME Int. J. Ser. C, 91-0375 B, 203−211
  15. Tanaka, H. and Machida, H. (1996). Half-toroidal traction-drive continuously variable power transmission. Engineering Tribology 210, 3, 205−2
  16. Walker, J. (1994). Three new mechanical-hydrostatic power-split transmissions unveiled at IAA. High Speed Diesels & Drives, Chicago