DOI QR코드

DOI QR Code

Column design of cold-formed stainless steel slender circular hollow sections

  • Young, Ben (Department of Civil Engineering, The University of Hong Kong) ;
  • Ellobody, Ehab (Department of Structural Engineering, Faculty of Engineering, Tanta University)
  • 투고 : 2005.03.23
  • 심사 : 2005.10.25
  • 발행 : 2006.08.25

초록

This paper describes the design and behaviour of cold-formed stainless steel slender circular hollow section columns. The columns were compressed between fixed ends at different column lengths. The investigation focused on large diameter-to-plate thickness (D/t) ratio ranged from 100 to 200. An accurate finite element model has been developed. The initial local and overall geometric imperfections have been included in the finite element model. The material nonlinearity of the cold-formed stainless steel sections was incorporated in the model. The column strengths, load-shortening curves as well as failure modes were predicted using the finite element model. The nonlinear finite element model was verified against test results. An extensive parametric study was carried out to study the effects of cross-section geometries on the strength and behaviour of stainless steel slender circular hollow section columns with large D/t ratio. The column strengths predicted from the parametric study were compared with the design strengths calculated using the American Specification, Australian/New Zealand Standard and European Code for cold-formed stainless steel structures. It is shown that the design strengths obtained using the Australian/New Zealand and European specifications are generally unconservative for the cold-formed stainless steel slender circular hollow section columns, while the American Specification is generally quite conservative. Therefore, design equation was proposed in this study.

키워드

참고문헌

  1. ABAQUS Standard User's Manual. (2004), Hibbitt, Karlsson and Sorensen, Inc. Vol. 1, 2 and 3, Version 6.4, USA
  2. ASCE (2002), Specification for the design of cold-formed stainless steel structural members. American Society of Civil Engineers, SEI/ASCE-8-02, Reston, Virginia
  3. AS (1991), Methods for tensile testing of metals. Australian Standard, AS 1391 - 1991, Standards Association of Australia, Sydney, Australia
  4. AS/NZS (2001), Cold-formed stainless steel structures. Australian/New Zealand Standard, AS/NZS 4673:2001, Standards Australia, Sydney, Australia
  5. EC3 (1996), Eurocode 3: Design of steel structures - Part 1.4: General rules - Supplementary rules for stainless steels. European Committee for Standardization, ENV 1993-1-4, CEN, Brussels
  6. Ellobody, E. and Young, B. (2005), 'Structural performance of cold-formed high strength stainless steel columns', J Construct. Steel Res., 61(12), 1631-1649 https://doi.org/10.1016/j.jcsr.2005.05.001
  7. Gardner, L. (2002), 'A new approach to structural stainless steel design', PhD Thesis, Department of Civil and Environmental Engineering, Imperial College of Science, Technology and Medicine, London
  8. Gardner, L. and Nethercot, D. A. (2004), 'Numerical modeling of stainless steel structural components - A consistent approach', J Struct. Eng., ASCE, 130(10), 1586-1601 https://doi.org/10.1061/(ASCE)0733-9445(2004)130:10(1586)
  9. Jiao, H. and Zhao, X. L. (2003), 'Imperfection, residual stress and yield slenderness limit of very high strength (VHS) circular steel tubes', J Constrnct. Steel Res., 59, 233-249 https://doi.org/10.1016/S0143-974X(02)00025-1
  10. Macdonald, M., Rhodes, J. and Taylor, G. T. (2000), 'Mechanical properties of stainless steel lipped channels', Proc. of the Fifteenth Int. Specialty Conf on Cold-formed Steel Strnctures, Eds R. A. LaBoube and W. W. Yu, St. Louis, University of Missouri-Rolla, Mo., USA, 673-686
  11. Ramberg, W. and Osgood, W. R. (1943), 'Description of stress strain curves by three parameters', Tech. Note No 902, National Advisory committee for Aeronautics, Washington, D.C
  12. Rasmussen, K. J. R. (2000), 'Recent research on stainless steel tubular structures', J Constrnct. Steel Res., 54, 75-88 https://doi.org/10.1016/S0143-974X(99)00052-8
  13. Rasmussen, K. J. R. and Hancock, G. J. (1993), 'Design of cold-formed stainless steel tubular members. I: Columns', J Struct. Eng., ASCE, 119(8),2349-2367 https://doi.org/10.1061/(ASCE)0733-9445(1993)119:8(2349)
  14. Rasmussen, K. J. R. and Rondal, J. (1997), 'Strength curves for metal columns', J Struct. Eng., ASCE, 113(6), 721-728
  15. Talja, A. and Salmi, P. (1995), 'Design of stainless steel RHS beams, columns and beam-columns', VTT Research Notes 1619, Technical Research Centre of Finland, Espoo
  16. Young, B. (2005), 'Local buckling and shift of effective centroid of cold-formed steel columns', Steel and Composite Structures, 5(2-3), 235-246 https://doi.org/10.12989/scs.2005.5.2_3.235
  17. Young, B. and Hartono, W. (2002), 'Compression tests of stainless steel tubular members', J Struct. Eng., ASCE, 128(6), 754-761 https://doi.org/10.1061/(ASCE)0733-9445(2002)128:6(754)
  18. Young, B. and Liu, Y. (2003), 'Experimental investigation of cold-formed stainless steel columns', J Struct. Eng., ASCE, 129(2), 169-176 https://doi.org/10.1061/(ASCE)0733-9445(2003)129:2(169)
  19. Young, B. and Lui, W. M. (2005), 'Behavior of cold-formed high strength stainless steel sections', J Struct. Eng., ASCE, 131(11), 1738-1745 https://doi.org/10.1061/(ASCE)0733-9445(2005)131:11(1738)
  20. Young, B. and Rasmussen, K. J. R. (1998), 'Tests of fixed-ended plain channel columns', J Struct. Eng., ASCE, 124(2), 131-139 https://doi.org/10.1061/(ASCE)0733-9445(1998)124:2(131)
  21. Young, B. and Rasmussen, K. J. R. (1999), 'Shift of effective centroid of channel columns', J Struct. Eng., ASCE, 125(5), 524-531 https://doi.org/10.1061/(ASCE)0733-9445(1999)125:5(524)

피인용 문헌

  1. Resistance of stainless steel CHS columns based on cross-section deformation capacity vol.64, pp.9, 2008, https://doi.org/10.1016/j.jcsr.2007.10.010
  2. Investigation of cold-formed stainless steel non-slender circular hollow section columns vol.7, pp.4, 2007, https://doi.org/10.12989/scs.2007.7.4.321
  3. Optimum Unbraced Length Ratios of Slender Steel Sections 2013, https://doi.org/10.7763/IJET.2013.V5.604
  4. Structural design of stainless steel concrete filled columns vol.64, pp.11, 2008, https://doi.org/10.1016/j.jcsr.2008.04.012
  5. Numerical Investigation of the Interaction of Local and Overall Buckling of Stainless Steel I-Columns vol.135, pp.11, 2009, https://doi.org/10.1061/(ASCE)ST.1943-541X.0000052
  6. A numerical investigation of local–overall interaction buckling of stainless steel lipped channel columns vol.65, pp.8-9, 2009, https://doi.org/10.1016/j.jcsr.2009.04.027
  7. Cross-section classification for cold-formed and built-up high strength carbon and stainless steel tubes under compression vol.106, 2015, https://doi.org/10.1016/j.jcsr.2014.12.019
  8. Local–Global Interaction Buckling of Stainless Steel I-Beams. II: Numerical Study and Design vol.141, pp.8, 2015, https://doi.org/10.1061/(ASCE)ST.1943-541X.0001131
  9. A consistent nonlinear approach for analysing steel, cold-formed steel, stainless steel and composite columns at ambient and fire conditions vol.68, 2013, https://doi.org/10.1016/j.tws.2013.02.016
  10. Nonlinear behaviour of eccentrically loaded FR concrete-filled stainless steel tubular columns vol.90, 2013, https://doi.org/10.1016/j.jcsr.2013.07.018
  11. Distortional–global interaction buckling of stainless steel C-beams: Part II — Numerical study and design vol.96, 2014, https://doi.org/10.1016/j.jcsr.2014.01.008
  12. Experimental Investigation on Stub-Column Behavior of Cold-Formed High-Strength Steel Tubular Sections vol.142, pp.5, 2016, https://doi.org/10.1061/(ASCE)ST.1943-541X.0001456
  13. Numerical modelling of fibre reinforced concrete-filled stainless steel tubular columns vol.63, 2013, https://doi.org/10.1016/j.tws.2012.10.005
  14. Structural state of stress analysis of concrete-filled stainless steel tubular short columns vol.87, pp.6, 2018, https://doi.org/10.1002/stab.201810610
  15. Buckling analysis of high strength stainless steel stiffened and unstiffened slender hollow section columns vol.63, pp.2, 2006, https://doi.org/10.1016/j.jcsr.2006.04.007
  16. Design of cold-formed stainless steel circular hollow section columns using direct strength method vol.163, pp.None, 2006, https://doi.org/10.1016/j.engstruct.2018.02.012
  17. Optimisation of flange and web slenderness for pre-engineered built-up steel sections vol.172, pp.8, 2006, https://doi.org/10.1680/jstbu.17.00186
  18. An Experimental Study on the Buckling Behaviors of Stainless Steel Tubular Columns Under Concentric Axial Compression vol.31, pp.4, 2006, https://doi.org/10.7781/kjoss.2019.31.4.273
  19. An Experimental Investigation on the Buckling Behaviors of Stainless Steel Square Hollow Section Compressive Members with Different Steel Grades vol.32, pp.5, 2020, https://doi.org/10.7781/kjoss.2020.32.5.309
  20. Finite element Analysis on Buckling Strength of Stainless Steel Circular Hollow Section Columns Under Concentric Axial Compression vol.20, pp.6, 2020, https://doi.org/10.1007/s13296-020-00366-w
  21. A unified approach for austenitic and ferritic stainless steel CHS beam–columns subjected to eccentric loading vol.165, pp.None, 2006, https://doi.org/10.1016/j.tws.2021.107918
  22. Tensile behavior of stainless steel S30408 at the Arctic low temperature vol.40, pp.5, 2006, https://doi.org/10.12989/scs.2021.40.5.633
  23. Flexural buckling of stainless steel CHS columns: Reliability analysis utilizing FEM simulations vol.188, pp.None, 2006, https://doi.org/10.1016/j.jcsr.2021.107002