DOI QR코드

DOI QR Code

A Study on the Extru-Bending Process of the Angle Product with 'Λ' Section Using Two Extrusion Billets

두 개의 압출빌렛을 사용하는 'Λ' 단면 앵글 구조재의 압출굽힘가공에 관한 연구

  • 이경국 (부경대학교 대학원 설계생산자동화전공) ;
  • 진인태 (부경대학교 기계공학부)
  • Published : 2005.04.01

Abstract

In the present study about extru-bending of angle product, the bending of extruded angle products with the $'\Lambda'$ section and 'ㄱ', section can be obtained using two extrusion billets by the hot metal extru-bending machine with the two punches moving in the different velocity. The bending curvature can be controlled by the different velocity of billets through the two-hole container. This paper describes simulations and experiments of extru-bending process that can make bending during extruding by the difference of stem velocities. And they are applied to two kinds of dies, that is, one of them is conical dies with symmetry $'\Lambda'$ section and the other one is conical dies with asymmetry 'ㄱ' section. The results of the forming simulation by $DEFORM^{TM}-3D$ and results of experiments show that the bending phenomenon at the die exit during extrusion can be obtained with two extrusion billet by the two stems moving in the different velocity. And it was known that it is possible to design the structure of conical cavity of extrusion dies and to control the curvature of product through the simulation and experiment of extru-bending process.

Keywords

References

  1. 박대윤, 진인태, 2001, 다지형 압출펀치의 상대 이동속도 차이에 의한 금속 곡관의 열간금속 압출 굽힘가공에 관한 연구, 한국소성가공학회 2001 춘계 학술대회논문집,pp.102-105
  2. 박중원, 진인태, 2002, 플랜지가 붙은 비대칭 단면형상 제품의 압출가공에 관한 연구, 한국소성가공학회 2002 추계학술대회논문집, pp. 78-81
  3. 이경국, 진인태, 2003,'ㄱ' 단면 형상 제품의 압출굽힘가공에 관한 연구, 한국소성가공학회 2003 춘계학술대회논문집, pp. 371-374
  4. 윤선홍, 이경국, 진인태, 2002 'ㄷ'단면형상의 알루미늄 제품의 열간 금속 압출굽힘가공에 관한 연구, 한국소성가공학회 2002 추계학술대회논문집, p. 86-89
  5. 김진훈, 진인태, 1998, 편심압출굽힘가공법에 의한 사각형 단면을 가진 중공 튜브제품의 U형 굽힘 가공에 관한 연구, 한국소성가공학회지, Vol7, No5, pp. 496-504
  6. 박태윤, 진인태, 2002, 열간금속 압출굽힘기를 이용한 금속 곡관의 압출굽힘가공에 관한 연구, 한국소성가공학회 2002 춘계학술대회논문집, pp. 262-268

Cited by

  1. Optimal design of an extrusion process for a hinge bracket vol.30, pp.5, 2016, https://doi.org/10.1007/s12206-016-0429-6