DOI QR코드

DOI QR Code

A method for effective beam widths of slabs in flat plate structures under gravity and lateral loads

  • Choi, Jung-Wook (Department of Civil & Environmental Engineering, University of Alberta, 3-059 Markin/CNRL Natural Resources Engineering Facility) ;
  • Song, Jin-Gyu (Division of Architecture, Chonnam National University)
  • Received : 2005.01.03
  • Accepted : 2005.10.06
  • Published : 2005.11.10

Abstract

Effective beam width models are commonly used to obtain the lateral stiffness of flat plate structures. In these models, an effective beam width is defined as the width when the flexural stiffness of the beam element equals the slab stiffness. In this present study, a method to obtain effective beam widths that considers the effects of connection geometry and slab cracking is analytically proposed. The rectangularity of the vertical member for the connection geometry and the combined effects of creep and shrinkage for the slab cracking are considered. The results from the proposed method are compared with experimental results from a test structure having nine slab-column connections.

Keywords

References

  1. Aalami, B. (1972), 'Moment-rotation relation between column and slab', ACI J., 69(5), 263-269
  2. ACI (2002), Building Code Requirements for Structural Concrete (ACI 318-02) and Commentary (ACI 3I8R-02), American Concrete Institute
  3. Allen, F.H. and Darvall, P.L. (1977), 'Lateral load equivalent frame', ACl J, 74(7), 294-299
  4. Grossman, J.S. (1997), 'Verification of proposed design methodologies for effective width of slabs in slabcolumn frames', ACl Struct. J., 94(2), 181-196
  5. Hwang, S.J. and Moehle, J.P. (1993), 'An experimental study of flat-plate structures under vertical and lateral loads', Report No. UCB/EERC-93/03, Earthquake Engineering Research Center, University of California, Berkeley
  6. Hwang, S.J. and Moehle, J.P. (2000), 'Models for laterally loaded slab-column frames', ACI Struct. J., 97(2), 345-352
  7. Hwang, S.J. and Moehle, J.P. (2000), 'Vertical and lateral load tests of nine-panel flat-plate frame', ACI Struct. J, 97(1), 193-203
  8. MIDAS/Gen Release 5.7.1 (2003), MIDAS Information Technology Co., Ltd., Seoul, Korea
  9. Moehle, J.P. and Diebold, J.w. (1984), 'Experimental study of the seismic response of a two story flat plate structure', Report No. UCB/EERC-84/08, Earthquake Engineering Research Center, University of California, Berkeley
  10. Pan, A.P. and Moehle, J.P. (1992), 'An experimental study of slab-column connections', ACI Struct. J., 89(6), 626-638
  11. Patrick, M.D. and Huo, X.S. (2004), 'Finite element modeling of slab-on-beam concrete bridge superstructures', Computers and Concrete, An Int. J., 1(3), 355-369 https://doi.org/10.12989/cac.2004.1.3.355
  12. Pecknold, D.A. (1975), 'Slab effective width for equivalent frame analysis', ACI J, 72(4), 135-137
  13. Robertson, L.N. and Durrani, A.J. (1992), 'Gravity load effect on seismic behavior of interior slab-column connections', ACl Struct. J., 89(1), 37-45
  14. Robertson, L.N. and Durrani, A.J. (1991), 'Gravity load effect on seismic behavior of exterior slab-column connections', ACl Struct. J. 88(3), 255-267
  15. Yun, Y.M. (2005), 'Strut-tie model evaluation of behavior of strength of pre-tensioned concrete deep beams', Computers and Concrete, An Int. J.,2(4),267-291 https://doi.org/10.12989/cac.2005.2.4.267

Cited by

  1. Unified equivalent frame method for flat plate slab structures under combined gravity and lateral loads - Part 1: derivation vol.7, pp.5, 2014, https://doi.org/10.12989/eas.2014.7.5.719